Nauki Techniczne

Archives of Civil Engineering

Zawartość

Archives of Civil Engineering | 2016 | No 2

Abstrakt

Self-curing concrete SC is a concrete type that can be cured without using any external curing regimes. It can perform by several methods such as using lightweight aggregate or chemical agents. In this research chemical curing agent is used to produce SC. This paper reports the results of a research study conducted to evaluate the effect of sulfates on the performance of self-curing concrete compared to ordinary concrete. Samples are immersed in sodium sulfate Na2S04 solution of 4% concentration. Results are measured in terms of compressive strength, tensile strength, flexural strength and mass loss. It was found that the rate of strength loss is noticed at ordinary concrete compared to SC concrete. Sulfate resistance is improved when using self-curing concrete. This improvement appears to be dependent on using a chemical curing agent.

Przejdź do artykułu

Autorzy i Afiliacje

A.A. Bashandy

Abstrakt

This paper presents application of optical microscope for evaluation of microtexture changes of coarse aggregate during simulated polishing in laboratory. Observations of the apparent changes on surfaces of seven different aggregates are presented. Simulation polishing of aggregate was performed in accordance with PN-EN 1097-8:2009. lmages of the aggregate surface were taken with the optical microscope in the reflection mode in particular stages of polishing. Digital images were analyzed. Standard deviation was determined on the basis of the histogram of intensities from digital images of the surfaces of aggregate grains which was assurned as the measure of changes in microtexture during simulated polishing (namely the σh parameter). Statistical analysis has shown that the changes of the σh parameter between the particular stages of polishing confirm certain trends related to the petrographic characteristic of the rocks. Aggregates which included minerals of similar hardness (granodiorite, dolomile, basalt) were more prone to polishing than gabbro and postglacial. Regeneration of the microtexture, the recovery to its original asperity, occurred in the case of quartz sandstone and steelmaking slag.

Przejdź do artykułu

Autorzy i Afiliacje

W. Gardziejczyk
M. Wasilewska

Abstrakt

The need to modify conventional pavement rises due to high maintenance cost of the highway systems. With the continuously increased consumption, a large amount of waste glass materials is generated annually in the world. This paper aims to study the performance of pavement asphalt in which a fractional aggregate is replaced with crushed glass. In this paper, some important properties of asphalt mix, including stability, flow, specific gravity and air voids are investigated. The original sample is prepared without adding glass for different percentages of bitumen. Other samples are prepared by adding crushed glass to the mix with 5%, 10%, and 15% by aggregate weight. The results show that the properties of glass-asphalt mixture are improved in comparison with normal asphalt pavement. lt is concluded that the use of waste glass in asphalt pavement is desirable.

Przejdź do artykułu

Autorzy i Afiliacje

Y. Issa

Abstrakt

Author explains a necessity of supply optimization to construction sites with small storage areas. This paper takes account of conditions existing in Poland. From among all factors discussed by the author, first of all, we should point at construction works on plots located in densely built-up areas, obtained by demolition of existing buildings, as well as a necessity of plots utilization after demolished buildings that technical conditions do not allow for further exploitation.

Przejdź do artykułu

Autorzy i Afiliacje

K.M. Kaczorek

Abstrakt

The aim of this paper is to present an assessment of the slip influence on the deflection of the steel plate-concrete composite beams, which are a new type of a design concept. The proposed method is based on the procedure included in the PN-EN 1992-1-1, which has been modified with taking into consideration interface slip. The theoretical analysis was verified by experimental studies.

Przejdź do artykułu

Autorzy i Afiliacje

D. Kisała
K. Furtak

Abstrakt

The article presents the ideas of flexible design in the construction sector. Flexibility in the construction sector was discussed and defined between typical and flexible approaches to design. The idea applied during the economic effectiveness analysis of construction projects was introduced. The issue of flexibility was discussed based on the example of construction of a sports facility - The National Stadium in Warsaw. An effectiveness analysis was applied for variant solutions.

Przejdź do artykułu

Autorzy i Afiliacje

M. Kośmieja
J. Pasławski

Abstrakt

The paper present the concept of stability assessing the of solutions which are construction schedules. Rank have been obtained through the use of task scheduling rules and the application of the KASS software. The aim of the work is the choice of the equivalent solution in terms of the total time of the project. The selected solution optimization task should be characterized by the highest resistance to harmful environmental risk factors. To asses the stability of schedule simulation technique was used.

Przejdź do artykułu

Autorzy i Afiliacje

M. Krzemiński

Abstrakt

Introduction of polymers into the cement composites improves same of the properties of concretes and mortars. Therefore, the polymer-cement composites are successfully used in construction. The model of microstructure formation in cement composites modified with thermoplastic polymer (pre-mix modifiers) has already been developed and successfully implemented. However, the formation of microstructure in the case of epoxy-cement composites (containing post-mix modifier) demonstrates same peculiarities which should be taken into account when modelling the process. The microstructure of epoxy-cement composites and its formation is discussed in the paper. The model is offered, formulated on the basis of the microscopic observations and results of testing.

Przejdź do artykułu

Autorzy i Afiliacje

P. Łukowski

Abstrakt

The subject of the analytical and experimental studies therein is of two metal seven-layer beam - plate bands. The first beam - plate band is composed of a lengthwise trapezoidally corrugated main core and two crosswise trapezoidally corrugated cores of faces. The second beam - plate band is composed of a crosswise trapezoidally corrugated main core and two lengthwise trapezoidally corrugated cores offaces. The hypotheses of deformation of a normal to the middle surface of the beams after bending are formulated. Equations of equilibrium are derived based on the theorem of minimum total potential energy. Three-point bending of the simply supported beams is theoretically and experimentally studied. The deflections of the two beams are determined with two methods, compared and presented.

Przejdź do artykułu

Autorzy i Afiliacje

E. Magnucka-Blandzi
P. Paczos
P. Wasilewicz
A. Wypych

Abstrakt

Accommodation tourist industry is characterized by high variability. For this category of services not only the location is crucial- that does not change, but also the standard, prices and seasonality of services. In the recent years, leisure centers performing functions only during the summer time have seen the possibility to extend their activities beyond the summer months. The reasons for this are the local investments requiring qualified staff which comes from different parts of the country, Europe and the world while creating dernand for accommodations. To meet the possible demand needs and to adapt to cold season, performing thermo-modernization works is necessary. In order to find the best solution and answer those needs, analysis of the profitability of the investrnents in a chosen holiday resort was carried out. The article presents the results of the analysis based on the payback period, LCC analysis and assessment of the investments risk.

Przejdź do artykułu

Autorzy i Afiliacje

R. Milwicz
P. Nowotarski

Abstrakt

The paper presents an approach to evaluating a building throughout its whole life cycle in relation to its sustainable development. It describes basic tools and techniques of evaluating and analysing the costs in the whole life cycle of the building, such as Life Cycle Assessment, Life Cycle Management, Life Cycle Cost and Social Life Cycle Assessment. The aim of the paper is to propose a model of cost evaluation throughout the building life cycle. The model is based on the fuzzy sets theory which allows the calculations to include the risks associated with the sustainable development, with the management of the investment and with social costs. Costs incurred in the subsequent phases of the building life cycle are analysed and modelled separately by means of a membership function. However, the effect of the analysis is a global cost evaluation for the whole life cycle of the building.

Przejdź do artykułu

Autorzy i Afiliacje

E. Plebankiewicz
K. Zima
D. Wieczorek

Abstrakt

The influence that general contractors and subcontractors have on the operation of a company is immense. Keeping this in mind, the authors have decided to develop and algorithm based on the analysis of partnering relations between construction companies that would select the best possible construction company for the purposes of cooperation. This algorithm, developed for a given construction company, is meant to support its decision-making system in the field of the selection of another construction company to cooperate with. The author has made references to earlier research, in which she had used the ELECTRE III method, and in which she bad analysed the possibility of applying the BIPOLAR method in order to solve the problem of the selection of a construction company to develop partnering relations with. The author provided an example of the calculations performed for a selection of construction companies.

Przejdź do artykułu

Autorzy i Afiliacje

E. Radziszewska-Zielina

Abstrakt

This article aims to identify potential risk factors affecting the implementation and synchronisation of surveying and construction works during building and operation of roads. The task was executed on the basis of literature studies and experience. The article is an introduction to the research that has been conducted by the authors on the reasonably precise index of factors which one may deal with during the implementation of facilities of this type. The raised issue is crucial for financial and time reasons, but what is important in the roads construction - also for social ones, as prolonged traffic disruption adversely affects the environment.

Przejdź do artykułu

Autorzy i Afiliacje

D. Skorupka
M. Kowacka

Abstrakt

Statistical conformity criteria for the compressive strength of concrete are a matter of debate. The criteria can have prejudicial effects on construction quality and reliability. Hence, the usefulness of statistical criteria for the small sample size n = 3 is questioned. These defects can cause a reduction in the quality of produced concrete and, consequently, too much risk for the recipient (investor). For this reason, the influence of conformity control on the value of the reliability index of concrete and reinforced concrete has been determined. The authors limited their consideration to the recommended standards PN-EN 206-1, PN-EN 1992 and ISO 2394 method of reliability index, which belongs to the analytical methods FORM (First Order Reliability Method). It assumes that the random variables are defined by two parameters of the normal distribution or an equivalent normal: the mean and the standard deviation. The impact of conformity control for n = 3 for concrete structures, designed according to the Eurocode 1992, for which the compressive strength of concrete is the capacity dominant parameter (sensitivity factor of dominating resistance parameter according to the FORM is 0.8), has been determined by evaluation of the reliability index.

Przejdź do artykułu

Autorzy i Afiliacje

I. Skrzypczak
L. Buda-Ożóg

Abstrakt

Planning a construction project, the investor frequently faces the choice of the option of the planned investment. Assessment of options is difficult due to the complex nature of construction projects. Various methods of multicriteria evaluation are successfully applied in the assessment and analysis of options. For those methods to work, a handful of information must be prepared beforehand. Among others, it is necessary to establish the assessment criteria and determine their weight for specific cases. This stage is implemented in cooperation with experts. The results of evaluations, obtained on the basis of the experts' opinions, must be processed and prepared. The paper will discuss one possible option for assessing the experts' opinion.

Przejdź do artykułu

Autorzy i Afiliacje

E. Szafranko

Abstrakt

Decision-making processes, including the ones related to ill-structured problems, are of considerable significance in the area of construction projects. Computer-aided inference under such conditions requires the employment of specific methods and tools (non-algorithmic ones), the best recognized and successfully used in practice represented by expert systems. The knowledge indispensable for such systems to perform inference is most frequently acquired directly from experts (through a dialogue: a domain expert - a knowledge engineer) and from various source documents. Little is known, however, about the possibility of automating knowledge acquisition in this area and as a result, in practice it is scarcely ever used. lt has to be noted that in numerous areas of management more and more attention is paid to the issue of acquiring knowledge from available data. What is known and successfully employed in the practice of aiding the decision-making is the different methods and tools. The paper attempts to select methods for knowledge discovery in data and presents possible ways of representing the acquired knowledge as well as sample tools (including programming ones), allowing for the use of this knowledge in the area under consideration.

Przejdź do artykułu

Autorzy i Afiliacje

J. Szelka
Z. Wrona

Abstrakt

Thin-walled bars currently applied in metal construction engineering belong to a group of members, the cross-section resistance of which is affected by the phenomena of local or distortional stability loss. This results from the fact that the cross-section of such a bar consists of slender-plate elements. The study presents the method of calculating the resistance of the cross-section susceptible to local buckling which is based on the loss of stability of the weakest plate (wall). The "Critical Plate" (CP) was identified by comparing critical stress in cross-section component plates under a given stress condition. Then, the CP showing the lowest critical stress was modelled, depending on boundary conditions, as an internal or cantilever element elastically restrained in the restraining plate (RP). Longitudinal stress distribution was accounted for by means of a constant, linear or non-linear (acc. the second degree parabola) function. For the critical buckling stress, as calculated above, the local critical resistance of the cross-section was determined, which sets a limit on the validity of the Vlasov theory. In order to determine the design ultimate resistance of the cross-section, the effective width theory was applied, while taking into consideration the assumptions specified in the study. The application of the Critical Plate Method (CPM) was presented in the examples. Analytical calculation results were compared with selected experimental findings. lt was demonstrated that taking into consideration the CP elastic restraint and longitudinal stress variation results in a more accurate representation of thin-walled element behaviour in the engineering computational model

Przejdź do artykułu

Autorzy i Afiliacje

A. Szychowski

Abstrakt

The paper presents selected aspects of dynamic numerical simulations of an orthotropic steel railway bridge loaded by high-speed trains. The model of moving loads was adopted in accordance with the models set out in the applicable standards. The current European code requirements are referred in which the computer calculations of the dynamic response of the structure are the basis for assessing the suitability of the structure to carry high-speed rail traffic ( v > 160 km/h ). In this research the calculations are based on the author's method of generating traffic roads in Abaqus FEM environment. lt is emphasized in the paper that in most commercial FEM codes (including Abaqus), moving loads are not implemented in modules responsible for defining of loads. The author's approach to this issue allowed to obtain results confirming its adequacy. In the longer term, the authors will develop a plan to adapt this algorithm in order to generale traftic loads on bridges discretized as spatial and plane numerical models.

Przejdź do artykułu

Autorzy i Afiliacje

A. Zbiciak
R. Oleszek
R. Michalczyk

Zasady etyki publikacyjnej

ETHICS POLICY

”Archives of Civil Engineering” respects and promotes the principles of publishing ethics. Being guided by COPE’s Guidelines ( https://publicationethics.org/resources/guidelines) we ensure that all participants of the publishing process comply with these rules, the journal pays special attention to:

Editor Responsibilities
1. Qualifying individual manuscripts for publication only on the basis of: (a) compliance with the guidelines provided to the authors, (b) substantive value, (c) originality, (d) transparency of presentation
2. Deciding whether the paper fulfills all requirements i.e. formal and scientific and which articles submitted to the journal should be published. In making these decisions, the editor may be guided by the policies of the journal’s editorial board as well as by legal requirements regarding libel, copyright infringement, and plagiarism.
3. Evaluating manuscripts for intellectual content without regard to race, gender, sexual orientation, religious belief, ethnic origin, citizenship, or political philosophy of the author(s).
4. Ensuring scientific accuracy and complying with the principle of authorship; making sure that individual authors who contribute to the publication accept its form after the scientific editing
5. Providing a fair and appropriate peer review process.
6. Withdrawing manuscripts from publication, if any information about its unreliability appeared, also as a result of unintentional errors, features of plagiarism or violation of the rules of publishing ethics were identified.
7. Requiring all contributors to disclose relevant competing interests and publish corrections if competing interests are revealed after publication. If needed, other appropriate action should be taken, such as the publication of a retraction or expression of concern.
8. Maintaining the integrity of the academic record, precludes business needs from compromising intellectual and ethical standards, and is always willing to publish corrections, clarifications, retractions, and apologies when needed.
9. Not disclosing any information about a manuscript under consideration to anyone other than the author(s), reviewers and potential reviewers, and in some instances the editorial board members, as appropriate.

Reviewer Responsibilities
1. Cooperating with the scientific editor and / or editorial office and the authors in the field of improving the reviewed material;
2. Being objective and expressing the views clearly with appropriate supporting arguments.
3. Assessing of the entrusted works in a careful and objective manner, if possible with an assessment of their scientific reliability and with appropriate justification of the comments submitted;
4. identifying relevant published work that has not been cited by the authors
5. calling to the editor's attention any substantial similarity or overlap between the manuscript under consideration and any other published data of which they have personal knowledge
6. Maintaining the principle of fair play, excluding personal criticism of the author (s)
7. Maintaining confidentiality, which is not showing or discussing with others except those authorized by the editor. Any manuscripts received for review are treated as confidential documents.
8. Performing a review within the set time limit or accepting another solution jointly with ACE in the event of failure to meet this deadline.
9. Notifying the editor if the invited reviewer feels unqualified to review the manuscript or knows that its timely review will be impossible.
10. identifying relevant published work that has not been cited by the authors
11. Not considering evaluating manuscripts in which they have conflicts of interest resulting from competitive, collaborative, or other relationships or connections with any of the authors, companies, or institutions connected to the submission.

Author Responsibilities
1. Results of original research should present an accurate account of the work performed as well as an objective discussion of its significance. Underlying data should be represented accurately in the manuscript. A paper should contain sufficient detail and references to permit others to replicate the work. Fraudulent or knowingly inaccurate statements constitute unethical behaviour and are unacceptable.
2. The authors should follow the principle of originality, which is submitting only their own original works, and in the case of using the works of other authors, marking them in accordance with the rules of quotation, or obtaining consent for the publication of previously published materials from their owners or administrators;
3. An author should not in general publish manuscripts describing essentially the same research in more than one journal or primary publication. Parallel submission of the same manuscript to more than one journal constitutes unethical publishing behaviour and is unacceptable.
4. Authorship should be limited to those who have made a significant contribution to the conception, design, execution, or interpretation of the reported study and phenomena such as ghostwriting or guest authorship in the event of their detection must be actively counteracted.
5. All authors should report in a Reliable manner the sources they used to create their own study and their inclusion in the attachment bibliography;
6. All those who have made significant contributions should be listed as co-authors. Where there are others who have participated in certain substantive aspects of the research project, they should be named in an Acknowledgement section.
7. The corresponding author should ensure that all appropriate co-authors (according to the above definition) and no inappropriate co-authors are included in the author list of the manuscript, and that all co-authors have seen and approved the final version of the paper and have agreed to its submission for publication.
8. All authors should disclose in their manuscript any financial or other substantive conflict of interest that might be construed to influence the results or their interpretation in the manuscript. All sources of financial support for the project should be disclosed.
9. When an author discovers a significant error or inaccuracy in his/her own published work, it is the author’s obligation to promptly notify the journal’s editor or publisher and cooperate with them to either retract the paper or to publish an appropriate erratum.

Publisher’s Confirmation
In cases of alleged or proven scientific misconduct, fraudulent publication or plagiarism the publisher, in close collaboration with the editors, will take all appropriate measures to clarify the situation and to amend the article in question. This includes the prompt publication of an erratum or, in the most severe cases, the complete retraction of the affected work.

Procedura recenzowania

Manuscript Peer-Review Procedure

”Archives of Civil Engineering” makes sure to provide transparent policies for peer-review, and reviewers have an obligation to conduct reviews in an ethical and accountable manner. There is clear communication between the journal and the reviewers which facilitates consistent, fair, and timely review.

-The model of peer-review is double-blind: the reviewers do not know the names of the authors, and the authors do not know who reviewed their manuscript (but if the research is published reviewers can eventually know the names of the authors). A complete list of reviewers is published in a traditional version of the journal: in-print.
-It is the editor who appoints two reviewers; however, if there are discrepancies in the assessment the third reviewer can be appointed.
-After having accepted to review the manuscript (one-week deadline), the reviewers have approximately 6 weeks to finish the process.
-The paper is published in ACE provided that the reviews are positive. All manuscripts receive grades from 1-5, 5 being positive, 1 negative, the authors receive reviews to read and consider the comments.
-Manuscript evaluations are assigned one of five outcomes: accept without changes, accept after changes suggested by the reviewer, rate manuscript once again after major changes and another review, reject, withdraw.
-Manuscripts requiring minor revision (accept after changes suggested by the reviewer) does not require a second review. All manuscripts receiving a "Rate manuscript once again after major changes and another review " evaluation must be subjected to a second review. Rejected manuscripts are given no further consideration. There are cases when the article can be withdrawn, often upon the request of an author, technical reason (e.g. names of authors are placed in the text, lack of references, or inappropriate structure of the text), or plagiarism.
-The revised version of the manuscript should be uploaded to the Editorial System within six weeks. If the author(s) failed to make satisfactory changes, the manuscript is rejected.
-On acceptance, manuscripts are subject to editorial amendment to suit house style.
-Paper publication requires the author's final approval.
- As soon as the publication appears in print and in electronic forms on the Internet there is no possibility to change the content of the article.

Editor’s responsibilities
-The editor decides whether the paper fulfills all requirements i.e. formal and scientific and which articles submitted to the journal should be published.
-In making these decisions, the editor may be guided by the policies of the journal’s editorial board as well as by legal requirements regarding libel, copyright infringement, and plagiarism.
-The editor maintains the integrity of the academic record, precludes business needs from compromising intellectual and ethical standards, and is always willing to publish corrections, clarifications, retractions, and apologies when needed.
-The editor evaluates manuscripts for intellectual content without regard to race, gender, sexual orientation, religious belief, ethnic origin, citizenship, or political philosophy of the author(s).
-The editor does not disclose any information about a manuscript under consideration to anyone other than the author(s), reviewers and potential reviewers, and in some instances the editorial board members, as appropriate.

Reviewers' responsibilities
Any manuscripts received for review are treated as confidential documents. They must not be shown to or discussed with others except if authorized by the editor. Privileged information or ideas obtained through peer review is kept confidential and not used for personal advantage Any invited reviewer who feels unqualified to review the manuscript or knows that its timely review will be impossible should immediately notify the editor so that alternative reviewers can be contacted. Reviewers should identify relevant published work that has not been cited by the authors. Any statement that an observation, derivation, or argument had been previously reported should be accompanied by the relevant citation. A reviewer should also call to the editor's attention any substantial similarity or overlap between the manuscript under consideration and any other published data of which they have personal knowledge. Reviewers should not consider evaluating manuscripts in which they have conflicts of interest resulting from competitive, collaborative, or other relationships or connections with any of the authors, companies, or institutions connected to the submission. Reviews should be conducted objectively. Personal criticism of the author is unacceptable. Referees should express their views clearly with appropriate supporting arguments. All reviews must be carried out on a special form available in the Editorial System.

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji