Applied sciences

Archives of Environmental Protection

Content

Archives of Environmental Protection | 2017 | vol. 43 | No 1 |

Abstract

The possibilities of remote sensing techniques in the field of the Earth surface monitoring and protection specifically for the problems caused by petroleum contaminations, for the mapping of insufficiently plugged and abandoned old oil wells and for the analysis of onshore oil seeps are described. Explained is the methodology for analyzing and detection of potential hydrocarbon contaminations using the Earth observation in the area of interest in Slovakia (Korňa) and in Czech Republic (Nesyt), mainly building and calibrating the spectral library for oil seeps. The acquisition of the in-situ field data (ASD, Cropscan spectroradiometers) for this purpose, the successful building and verification of hydrocarbon spectral library, the application of hydrocarbon indexes and use of shift in red-edge part of electromagnetic spectra, the spectral analysis of input data are clarified in the paper. Described is approach which could innovate the routine methods for investigating the occurrence of hydrocarbons and can assist during the mapping and locating the potential oil seep sites. Important outcome is the successful establishment of a spectral library (database with calibration data) suitable for further application in data classification for identifying the occurrence of hydrocarbons.

Go to article

Abstract

Fire has considerable impact on vegetation and organic soils properties. As we observed that the differences between vegetation of burnt and unburnt areas on the rich fen are visible 11 years after the fire, we assumed that the post-fire changes are long lasting, yet limited exclusively to the burnt areas. In order to check this hypothesis we studied spatial differentiation of physical and chemical properties of soils, and productivity capacities of burnt and unburnt areas in the fen in Biebrza National Park. We took soil samples from the neighboring burnt and unburnt areas, from the depth of 0–30 cm and 30–50 cm. We analyzed 21 parameters of the soils including: pH, ash content, moisture, bulk density, exchangeable K, Na, Ca, available P, N-NH4+, N-NO3−, total N, C, K, Na, Ca, Mg, Fe, P; and calculated C:N, C:P ratios. Surface layer of the burnt soils differed significantly from the unburnt soils in respect of 17 out of 21 parameters. The most pronounced difference was observed for available phosphorous (on average 6 times higher for the burnt soils). The differences in the deeper layer were mostly insignificant. The burnt areas were also characterized by twofold higher plant productivity than recorded for the unburnt areas. The influence of fire on peaty soils was long lasting but mostly limited to the surface layer of the soils. In the case of particular soil features, the post-fire differences were modified by advanced muck formation (moorshing) processes in the unburnt areas. Since the fire led to long lasting increase of fertility, the recovery of fen vegetation is unlikely.

Go to article

Abstract

Surfactants after their use are discharged into aquatic ecosystems. These compounds may be harmful to fauna and flora in surface waters or can be toxic for microorganisms of the activated sludge or biofilm in WWTP. In order to determine effectiveness of different advanced oxidation processes on the degradation of surfactants, in this study the degradation of anionic surfactants in aqueous solution using photolysis by 254 nm irradiation and by advanced oxidation process in a H2O2/UVC system was investigated. Two representatives of anionic surfactants, linear alkyl benzene sulphonate (LAS-R11–14) and ether carboxylic derivate (EC-R12–14E10) were tested. The influence of pH, initial surfactant concentration and dose of hydrogen peroxide on the degradation was also studied. Results show outstanding effectiveness of the H2O2/UVC system in the removal of surfactant from aqueous solutions.

Go to article

Abstract

One of the most important problems concerning contaminant transport in the ground is the problem related to the definition of parameters characterizing the adsorption capacity of ground for the chosen contaminants relocating with groundwater. In this paper, for chloride and sulfate indicators relocating in sandy ground, the numerical values of retardation factors (Ra) (treated as average values) and pore groundwater velocities with adsorption (ux/Ra) (in micro-pore ground spaces) are taken into consideration. Based on 2D transport equation the maximal dimensionless concentration values (C*max c) in the chosen ground cross-sections were calculated. All the presented numerical calculations are related to the unpublished measurement series which was marked in this paper as: October 1982. For this measurement series the calculated concentration values are compared to the measured concentration ones (C*max m) given recently to the author of this paper. In final part of this paper the parameters characterizing adsorption capacity (Ra, ux/Ra) are also compared to the same parameters calculated for the two earlier measurement series. Such comparison also allowed for the estimation of a gradual in time depletion of adsorption capacity for the chosen sandy ground.

Go to article

Abstract

Gala Lake National Park that has an international importance is one of the most important wetland ecosystems for Turkey. As same as many aquatic habitats, Gala Lake is under a significant anthropogenic pressure originated from agricultural activities conducted around the lake and from industrial discharges by means of Ergene River.

The aim of this study was to evaluate the sediment quality of Gala Lake and Irrigation Canal by investigating some toxic element accumulations (As, B, Ni, Cr, Pb, Cd, Zn and Cu) from a statistical perspective. Pearson Correlation Index (PCI) and Factor Analysis (FA) were applied to detected data in order to determine the associated contaminants and effective factors on the system. Potential Ecological Risk Index (RI) and Biological Risk Index based sediment quality guidelines (mERM-Q) applied to detected data in order to assess the ecological and biological risks of heavy metals in the ecosystem. Also Geographic Information System (GIS) technology was used to make visual explanations by presenting distribution maps of investigated elements.

According to the results of PCI, significant positive correlations were recorded among the investigated toxic elements at 0.01 significance level. According to the results of FA, two factors, which were named as “Agricultural Factor” and “Industrial Factor”, explained 86.6% of the total variance. According to the results of Potential Ecological Risk Index, cadmium was found to be the highest risk factor and according to results of Biological Risk Index, nickel and chromium were found to be the highest risk factors for Gala Lake and Irrigation Canal. As a result of the present study, it was also determined that heavy metal contents in sediments of Gala Lake National Park reached to critical levels and the system is intensively under effect of agricultural and industrial originated pollution.

Go to article

Abstract

The paper investigates the air quality in the urban area of Warsaw, Poland. Calculations are carried out using the emissions and meteorological data from the year 2012. The modeling tool is the regional CALMET/CALPUFF system, which is used to link the emission sources with the distributions of the annual mean concentrations. Several types of polluting species that characterize the urban atmospheric environment, like PM10, PM2.5, NOx, SO2, Pb, B(a)P, are included in the analysis. The goal of the analysis is to identify the most polluted districts and polluting compounds there, to check where the concentration limits of particular pollutants are exceeded. Then, emission sources (or emission categories) which are mainly responsible for violation of air quality standards and increase the adverse health effects, are identified. The modeling results show how the major emission sources – the energy sector, industry, traffic and the municipal sector – relate to the concentrations calculated in receptor points, including the contribution of the transboundary inflow. The results allow to identify districts where the concentration limits are exceeded and action plans are needed. A quantitative source apportionment shows the emission sources which are mainly responsible for the violation of air quality standards. It is shown that the road transport and the municipal sector are the emission classes which substantially affect air quality in Warsaw. Also transboundary inflow contributes highly to concentrations of some pollutants. The results presented can be of use in analyzing emission reduction policies for the city, as a part of an integrated modeling system.

Go to article

Abstract

The decomposition of hydrocarbons using combined advanced oxidation methods is largely considered owing to abundant production of OH radicals and the potential economic advantages. In this study, the synergetic effect of ozonation on photocatalytic oxidation of chloroform and chlorobenzene over expanded graphite-TiO2&ZnO Nano composite was investigated. The effect of introduced ozone concentration and residence time was also examined on removal efficiency. The results showed that the removal efficiency was significantly enhanced by the combined system resulting from the additional oxidation process causing active species to be increased. Increasing the introduced ozone concentration which generates more reactive compounds had a greater effect on the removal efficiency than that of residence time. However, from the mineralization point of view, the residence time had a dominant effect, and the selectivity towards CO2 was dramatically declined when the flow rate increased. Based on these results, the combined system is preferred due to higher removal efficiency and complete mineralization.

Go to article

Abstract

The most common chemical’s spills in typical transportation accidents are those with petroleum products such as diesel fuel, the consequence of which is an extensive pollution of the soil. In order to plan properly fuel recovery from the soil, it is important to gain information about the soil depth which may be affected by pollutant and to predict the pollutant concentration in different soil layers. This study deals with the impact of basic atmospheric conditions, i.e. air temperature and humidity on the diesel fuel migration through the soil. The diesel fuel was spilled into columns (L = 30 cm; D = 4.6 cm) filled with sandy and clay soil samples, and its concentrations at various depths were measured after 11 days under various air temperature (20 and 40°C) and relative humidity (30–100%) conditions. The effects observed were explained by understanding physical processes, such as fuel evaporation, diffusion and adsorption on soil grains. The increase in temperature results in higher fuel evaporation loss and its faster vertical migration. The relative humidity effect is less pronounced but more complex, and it depends much on the soil type.

Go to article

Abstract

Applying pesticides to crops is one of the causes of water pollution by surface runoff, and chlorpyrifos, trifluralin and chlorothalonil are used respectively as insecticide, herbicide and fungicide for crop plants widely. To explore effects of three pesticides on aquatic organisms, superoxide dismutase (SOD) and glutathione S-transferase (GST) activities were determined after 24 h and 48 h exposure of D. magna with ages of 6–24 h to several low concentrations of chlorpyrifos (0.36, 0.72, 1.43, 2.86, 5.72 μg∙L−1), trifluralin (0.17, 0.33, 0.66, 1.33, 2.65 mg∙L−1) and chlorothalonil (0.09, 0.18, 0.36, 0.72, 1.43 mg∙L−1) respectively. Main reproductive parameters including first pregnancy time, first brood time, the number of first brood and total fecundity after 21 d exposures at the same concentrations of pesticides as described above were also measured. The results showed that the activities of GST increased in lower concentrations and decreased in higher concentrations after 24 h exposure to three pesticides, respectively. The activities of SOD showed the same changes after 48 h exposure. With the time prolonged, the activities of GST decreased while the activities of SOD increased. After 21 d exposure, the first pregnancy time and first brood time were delayed, while the number of the first brood and total fecundity per female decreased with increasing concentrations. These results corroborated that GST activity was more sensitive to those pesticides than SOD activity, and there was a significant relationship between total fecundity and pesticides-dose(r>0.94, n=6), GST activity after 48 h exposure and total fecundity after 21 d exposure (r>0.92, n=6).

Go to article

Abstract

Priority wise channelization of resources is the key to successful environmental management, especially when funds are limited. The study in hand has successfully developed an algorithmic criterion to compare hazardous effects of Municipal Solid Waste (MSW) dumping sites quantitatively. It is a Multi Criteria Analysis (MCA) that has made use of the scaling function to normalize the data values, Analytical Hierarchy Process (AHP) for assigning weights to input parameters showing their relevant importance, and Weighted Linear Combination (WLC) for aggregating the normalized scores. Input parameters have been divided into three classes namely Resident’s Concerns, Groundwater Vulnerability and Surface Facilities. Remote Sensing data and GIS analysis were used to prepare most of the input data. To elaborate the idea, four dumpsites have been chosen as case study, namely Old-FSD, New-FSD, Saggian and Mahmood Booti. The comparison has been made first at class levels and then class scores have been aggregated into environmental normalized index for environmental impact ranking. The hierarchy of goodness found for the selected sites is New-FSD > Old-FSD > Mahmood Booti > Saggian with comparative scores of goodness to environment as 36.67, 28.43, 21.26 and 13.63 respectively. Flexibility of proposed model to adjust any number of classes and parameters in one class will be very helpful for developing world where availability of data is the biggest hurdle in research based environmental sustainability planning. The model can be run even without purchasing satellite data and GIS software, with little inaccuracy, using imagery and measurement tools provided by Google Earth.

Go to article

Abstract

This paper present the data for monitoring forest conditions and forest resource management by a local community adjacent to the Doi Laung Wildlife Sanctuary, Huaimai Sub-district, Song District, Phrae Province, Thailand. This study uses quantitative forest surveys, interviews, discussions, and descriptions of the historical context of public participation in forest management including a detailed assessment of field conditions. The findings of a forest resources inventory show that (1) from the three sampled areas, Doi Laung Wildlife Sanctuary has highest richness, followed by village #16 and #14, and (2) Huaikhon #16 implied the process of framework to maintain a healthy condition and response to community needs with collective management. The conceptual model assessment that links key group indicators and drivers is presented based on previously developed assessment models. The framework focuses on the best way to provide forest management, forest fire prevention, and firefighting as well as monitoring of Check-dam construction and other activities that support the recovery of the forest community. This paper demonstrates the general of an environmental assessment framework to applying organize environmental information to facilitate policy decision making for the sustainable development.

Go to article

Editorial office

Editors

Editor-in-Chief
Czesława Rosik-Dulewska

Editorial Advisory Board
Michał Bodzek
Katarzyna Juda-Rezler
Korneliusz Miksch

Assistant Editor
Katarzyna Panz

 

Editorial Board:

President:
Lucjan Pawłowski

Members:
Brian A. Bolto (Australia)
Hubert Bril (France)
Bart Van der Bruggen (Belgium)
Zhihong Cao (China)
Pen-Chi Chiang (R.O.C.)
Wolfgang Frenzel (Germany)
Reinhard F. Hüttl (Germany)
Piotr Kowalik (Poland)
Joanna Kyzioł-Komosińska (Poland)
Rajmund Michalski (Poland)
Anuska Mosquera Corral (Spain)
Takashi Nakamura (Japan)
Józef M. Pacyna (Norway)
Wim H. Rulkens (The Nederlands)
Corrado Sarzanini (Italy)
Hans Martin Seip (Norway)
Jan Siuta (Poland)
Jerzy Sobota (Poland)
Joanna Surmacz-Górska (Poland)
Jadwiga Szczepańska (Poland)
Christopher G. Uchrin (USA)
Tomasz Winnicki (Poland)
Xiaoping Zhu (USA)
Jerzy Zwoździak (Poland) 

Contact

Institute of Environmental Engineering of the Polish Academy of Sciences
ul. M. Skłodowskiej-Curie 34, 41-819 Zabrze, Poland
Tel.: +48-32-271 64 81      Fax: +48-32-271 74 70
e-mail: aep@ipis.zabrze.pl

Instructions for authors

Instructions for Authors

Archives of Environmental Protection is a quarterly published jointly by the Institute of Environmental Engineering of the Polish Academy of Sciences and the Committee of Environmental Engineering of the Polish Academy of Sciences. Thanks to the cooperation with outstanding scientists from all over the world we are able to provide our readers with carefully selected, most interesting and most valuable texts, presenting the latest state of research in the field of engineering and environmental protection.

Scope

The Journal principally accepts for publication original research papers covering such topics as:

- Air quality, air pollution prevention and treatment;

- Wastewater treatment and utilization;

- Waste management;

- Hydrology and water quality, water treatment;

- Soil protection and remediation;

- Transformations and transport of organic/inorganic pollutants in the environment;

- Measurement techniques used in environmental engineering and monitoring;

- Other topics directly related to environmental engineering and environment protection.

The Journal accepts also authoritative and critical reviews of the current state of knowledge in the topic directly relating to the environment protection.

If unsure whether the article is within the scope of the Journal, please send an abstract via e-mail to: aep@ipis.zabrze.pl

Preparation of the manuscript

The following are the requirements for manuscripts submitted for publication:

• The manuscript (with illustrations, tables, abstract and references) should not exceed 20 pages. In case the manuscript exceeds the required number of pages, we suggest contacting the Editor.

• The manuscript should be written in English.

• The manuscript ought to be submitted in doc or docx format in three files:

– text.doc – file containing the entire text, without title, keywords, authors names and affiliations, and without tables and figures;

– figures.doc – file containing illustrations with legends;

– tables.doc – file containing tables with legends;

• The text should be prepared in A4 format, 2.5 cm margins, 1.5 spaced, preferable using Time New Roman font with no less than 12 point. The text should be divided into sections and subsections according to general rules of manuscript editing. The proposed place of tables and figures insertion should be marked in the text.

• Legends in the figures should be concise and legible, using a proper font size so as to maintain their legibility after decreasing the font size. Please avoid using descriptions in figures, these should be used in legends or in the text of the article. Figures should be placed without the box. Legends should be placed under the figure and also without box.

• Tables should always be divided into columns. When there are many results presented in the table it should also be divided into lines.

• References should be cited in the text of an article by providing the name and publication year in brackets, e.g. (Nowak 2019). When a cited paper has two authors, both surnames connected with the word “and” should be provided, e.g. (Nowak and Kowalski 2019). When a cited paper has more than one author, surname of its first author, abbreviation ‘et al.’ and publication year should be provided, e.g. (Kowalski et al. 2019). When there are more than two publications cited in one place they should be divided with coma, e.g. (Kowalski et al. 2019, Nowak 2019, Nowak and Kowalski 2019). Internet sources should be cited like other texts - providing the name and publication year in brackets.

• References should be listed at the end of the article ordered alphabetically by surname of the first author. References should be made according to the following rules:

1. Journal:

Surnames and initials. (publication year). Title of the article, Journal Name, volume, number, pages, DOI.

For example:

Nowak, S.W., Smith, A.J. & Taylor, K.T. (2019). Title of the article, Archives of Environmental Protection, 10, 2, pp. 93–98, DOI: 10.24425/aep.2019.126330.

2. Book:

Surnames and initials. (publication year). Title, Publisher, Place and publishing year.

For example:

Kraszewski, J. & Kinecki, K. (2019). Title of book, Work & Sudies, Zabrze 2019.

3. Edited book:

Surnames and initials of text authors. (publishing year). Title of cited chapter, in: Title of the book, Surnames and initials of editor(s). (Ed.)/(Eds.). Publisher, Place, pages.

For example:

Reynor, J. & Taylor, K.T. (2019). Title of chapter, in: Title of the cited book, Kaźmierski, I. & Jasiński, C. (Eds.). Work & Studies, Zabrze, pp. 145–189.

4. Internet sources:

Surnames and initials or the name of the institution which published the text. (publication year). Title, (website address (accessed on)).

For example:

Kowalski, M. (2018). Title, (http://www.krakow.pios.gov.pl/publikacje/2009/ (03.12.2018)).

5. Patents:

Orszulik, E. (2009). Palenisko fluidalne, Patent polski: nr PL20070383311 20070910 z 16 marca 2009.

Smith, I.M. (1988). U.S. Patent No. 123,445. Washington, D.C.: U.S. Patent and Trademark Office.

6. Materials published in language other than English:

Titles of cited materials should be translated into English. Information of the language the materials were published in should be provided at the end.

For example:

Nowak, S.W. & Taylor, K.T. (2019). Title of article, Journal Name, 10, 2, pp. 93–98, DOI: 10.24425/aep.2019.126330. (in Polish)

Not more than 30 references should be cited in the original research paper.

Submission of the manuscript

By submitting the manuscript Author(s) warrant(s) that the article has not been previously published and is not under consideration by another journal. Authors claim responsibility and liability for the submitted article. The manuscripts should be submitted on-line using the Editorial System available at http://www.editorialsystem.com/aep. Authors are asked to propose at least 4 potential reviewers, including 2 from Poland, together with their e-mail addresses. The journal does not have article processing charges (APCs) nor article submission charges.

Review Process

All the submitted articles are assessed by the Editorial Board. If positively assessed by at least two editors, Editor in Chief, along with department editors selects two independent reviewers from recognized authorities in the discipline. Reviewers receive a text of the article (without personal data of Authors) and review forms applicable in the journal. In justified cases, reviewers receive additional questions regarding the article. Review process usually lasts from 1 to 4 months.

After completion of the review process Authors are informed of the results and - if both reviews are positive - asked to correct the text according to reviewers’ comments. Next, the revised work is verified by the editorial staff for factual and editorial content.

Acceptance of the manuscript

The manuscript is accepted for publication on grounds of the opinions of independent reviewers and approval of Editorial Board. Authors are informed about the decision and also asked to pay processing charges and to send completed declaration of the transfer of copyright to the editorial office.

Proofreading and Author Correction

All articles published in the Archives of Environmental Protection go through professional proofreading process. If there are too many language errors that prevent understanding of the text, the article is sent back to Authors with a request to correct the indicated fragments or - in extreme cases – to re-translate the text.

After proofreading the manuscript is prepared for publishing. The final stage of the publishing process is Author correction. Authors receive a page proof copy of the article with a request to make final corrections.

Article publication charges

The publication fee of an article in the Journal is:

• 20 EUR/80 zł per page (black and white or in gray scale),

• 30 EUR/120 zł per page (color).

Payments in Polish zlotys

Bank BGK

Account no.: 20 1130 1091 0003 9111 7820 0001

Payments in Euros

Bank BGK

Account no.: 20 1130 1091 0003 9111 7820 0001

IBAN: PL 20 1130 1091 0003 9111 7820 0001

SWIFT: GOSKPLPW

Authors are kindly requested to inform the editorial office of making payment for the publication, as well as to send all necessary data for issuing an invoice.

Open Access policy

Archives of Environmental Protection jest czasopismem wydawanym w wolnym dostępie na licencji CC BY-NC-SA 4.0.

Archives of Environmental Protection is an open access journal with all content available with no charge in full text version. The journal content is available under the licencse CC BY-NC-SA 4.

Additional information

Abstracting & Indexing

Archives of Environmental Protection is covered by the following services:

AGRICOLA (National Agricultural Library)

AGRIS

Arianta

Baidu Scholar

BazTech

CABI (over 50 subsections)

Chemical Abstracts Service (CAS) - CAplus

Chemical Abstracts Service (CAS) - SciFinder

CNKI Scholar (China National Knowledge Infrastructure)

CNPIEC

Dimensions

DOAJ (Directory of Open Access Journals)

EBSCO (relevant databases)

EBSCO Discovery Service

Engineering Village

FSTA - Food Science & Technology Abstracts

Genamics JournalSeek

GeoArchive

GeoRef

Google Scholar

Index Copernicus

Inspec

Japan Science and Technology Agency (JST)

J-Gate

Journal Citation Reports/Science Edition

JournalTOCs

KESLI-NDSL (Korean National Discovery for Science Leaders)

Microsoft Academic

Naviga (Softweco)

Primo Central (ExLibris)

ProQuest (relevant databases)

Publons

ReadCube

Reaxys

SCOPUS

Sherpa/RoMEO

Summon (Serials Solutions/ProQuest)

TDNet

TEMA Technik und Management

Ulrich's Periodicals Directory/ulrichsweb

WanFang Data

Web of Science - Biological Abstracts

Web of Science - BIOSIS Previews

Web of Science - Science Citation Index Expanded

WorldCat (OCLC)

This page uses 'cookies'. Learn more