Applied sciences

Archive of Mechanical Engineering

Content

Archive of Mechanical Engineering | 2015 | vol. 62 | No 1 |

Abstract

A thermoelastic boundary value problem of a hollow circular disc made of functionally graded materials with arbitrary gradient is analysed. The steady-state temperature distribution is assumed to be the function of the radial coordinate with prescribed temperature at the inner and outer cylindrical boundary surfaces. The material properties are assumed to be arbitrary smooth functions of the radial coordinate. A coupled system of ordinary differential equations containing the radial displacement and stress function is derived and used to get the distribution of thermal stresses and radial displacements caused by axisymmetric mechanical and thermal loads. General analytical solutions of functionally graded disc with thermal loads are not available. The results obtained by the presented numerical method are verified by an analytical solution. The considered analytical solution is valid if the material properties, except the Poisson ratio, are expressed as power functions of the radial coordinate.

Go to article

Abstract

The paper deals with experimental investigations of a set of metal wave-ring gaskets of different thickness and different assembly interference. The gaskets were examined under assembly conditions, i.e. pressed in their seats with no operating pressure applied. The electric resistance wire strain gauges were used to measure the circumferential and axial strains at the inner surface of the gaskets. The traces of contact at the working surface of the gaskets were measured after disassembly the gaskets from their seats. The material tests were carried out to determine the real mechanical properties of materials applied for the gaskets and the seats. The results of experiment were verified by FEM calculations and compared with the analytical approach based on the simplified shell model proposed for the gasket.

Go to article

Abstract

The box wing system is an unconventional way to connect the lifting surfaces that the designers willingly to use in prototypes of new aircrafts. The article present a way to quickly optimize the wing structure of box wing airplane that can be useful during conceptual design. At the beginning, there is presented theory and methods used to code optimization program. Structure analysis is based on FEM beam model, which is sufficient in conceptual design. Optimization is performed using hybrid method, connection of simple iteration and gradient descent methods. Finally, the program is validated by case study.

Go to article

Abstract

In multi-stage wire drawing machines productivity growth can be achieved at higher drawing speeds by preventing wire breakage during the process. One disadvantage of high-speed wire drawing is the requirement imposed by machine dynamics in terms of its stability and reliability during operation. Tensile forces in the wire must maintained by fast synchronization of all capstans speed. In this process, the displacement sensors play the main role in providing the control system with feedback information about the wire condition. In this study, the influences between the sensors and actuator driven capstans have been studied, and tuner roll concept of a wire drawing machine was experimentally investigated. To this aim, measurements were carried out on two drawing stages at different drawing speeds and obtained results were presented. These results clearly show the fast changes of the capstans speed and the angular displacements of the rollers that tighten the wire, which only confirms the high dynamics of the wire drawing machine.

Go to article

Abstract

The aim of the study is to identify the relevant aspects of numerical analysis of impact of projectiles with soft cores into a package composed of thin flexible plies located on the plastic backing. In order to illustrate the problem, normal impact of 7.62 mm TT projectile into an unclamped package comprising 36 plies of Dyneema SB71 supported on the plastic backing was selected. The problem was solved with the use of the finite element method (FEM) with the explicit integration scheme (central difference method) of motion equations in the matrix form. Based on the conducted numerical computations, it was revealed that obtaining the extreme deformations of a projectile soft core and the backing material in Lagrangian description requires employment of adaptive methods. The proposed R-adaptive method performs its role but must be used carefully due to the mass loss which may appear during calculations.

Go to article

Abstract

The paper presents a solution of the control system for fatigue test stand MZGS-100 PL, comprising the integrated Real-Time controller based on FPGA (Field-Programmable Gate Array) technology with LabVIEW software. The described control system performs functions such as continuous regulation of speed induction motor, measuring strain of the lever machine and the test specimen, displacement of the polyharmonic vibrator, as well as the elimination of interferences, overload protection and emergency stop of the machine. The fatigue test stand also allows to set the pseudo-random history of energy parameter W(t).

Go to article

Abstract

The rigid finite element method (RFEM) has been used mainly for modelling systems with beam-like links. This paper deals with modelling of a single set of electrodes consisting of an upper beam with electrodes, which are shells with complicated shapes, and an anvil beam. Discretisation of the whole system, both the beams and the electrodes, is carried out by means of the rigid finite element method. The results of calculations concerned with free vibrations of the plates are compared with those obtained from a commercial package of the finite element method (FEM), while forced vibrations of the set of electrodes are compared with those obtained by means of the hybrid finite element method (HFEM) and experimental measurements obtained on a special test stand.

Go to article

Abstract

The paper focuses on the influence of the longitudinal and lateral suspension damping in correlation with the velocity upon the vibration behaviour of the railway vehicles while moving on a tangent track. The numerical simulations are developed based on a linear model of a 17-degree of freedom vehicle that allows the evaluation of the dynamic behaviour of the vehicle in a sub-critical velocity. Based on the response frequency functions of the vehicle in a harmonic and in a random behaviour, a series of basic properties of the stable behaviour of the forced lateral vibrations has been made evident, as well as the opportunities to lower the level of the carbody vibrations by changing the suspension damping.

Go to article

Editorial office

Editor-in-Chief

Prof. Marek Wojtyra, Warsaw University of Technology, Poland

 

Editorial Board

Prof. Krzysztof Arczewski, Warsaw University of Technology, Poland

Prof. Janusz T. Cieśliński, Gdańsk University of Technology, Poland

Prof. Antonio Delgado, LSTM University of Erlangen-Nuremberg, Germany

Prof. Peter Eberhard, University of Stuttgart, Germany

Prof. Jerzy Maciej Floryan, The University of Western Ontario, Canada

Prof. Janusz Frączek, Warsaw University of Technology, Poland

Prof. Tadeusz Ryszard Fodemski, Technical University of Lodz, Poland

Prof. Zbigniew Kowalewski, Institute of Fundamental Technological Research, Polish Academy of Sciences, Poland

Prof. Zenon Mróz, Institute of Fundamental Technological Research, Polish Academy of Sciences, Poland

Prof. Andrzej J. Nowak, Silesian University of Technology, Poland

Dr. Andrzej F. Nowakowski, The University of Sheffield, United Kingdom

Prof. Jerzy Sąsiadek, Carleton University, Canada

Prof. Jacek Szumbarski, Warsaw University of Technology, Poland

Prof. Tomasz Wiśniewski, Warsaw University of Technology, Poland

Prof. Günter Wozniak, Chemnitz University of Technology, Germany

 

Assistant to the Editor

Małgorzata Broszkiewicz, Warsaw University of Technology, Poland

 

Editorial Advisory Board

Prof. Alberto Carpinteri, Politecnico di Torino, Italy

Prof. Fernand Ellyin, University of Alberta, Canada

Prof. Feng Gao, Shanghai Jiao Tong University, P.R. China

Prof. Emmanuel E. Gdoutos, Democritus University of Thrace, Greece

Prof. Gregory Glinka, University of Waterloo, Ontario, Canada

Prof. Andrius Marcinkevicius, Vilnius Gedeminas Technical University, Lithuania

Prof. Manuel José Moreira De Freitas, Instituto Superior Tecnico, Portugal

Prof. Andrzej Neimitz, Kielce University of Technology, Poland

Prof. Thierry Palin-Luc, Arts et Métiers ParisTech, Institut Carnot Arts, France

Prof. Andre Pineau, Centre des Matériaux, Ecole des Mines de Paris, France

Prof. Narayanaswami Ranganathan, LMR, Ecole Polytechnique de l'Université de Tours, France

Prof. Jan Ryś, Cracow University of Technology, Poland

Prof. Adelia Sequeira, Technical University of Lisbon, Portugal,

Prof. Józef Szala, University of Technology and Life Sciences in Bydgoszcz, Poland

Prof. Edmund Wittbrodt, Gdańsk University of Technology, Poland

Prof. Jens Wittenburg, Karlsruhe Institute of Technology, Germany

Prof. Stanisław Wojciech, University of Bielsko-Biała, Poland

 

Language Editor

Lech Śliwa, Institute of Physiology and Pathology of Hearing, Warsaw, Poland

  

Contact

ARCHIVE OF MECHANICAL ENGINEERING

Editorial Office:

Institute of Aeronautics and Applied Mechanics, Warsaw University of Technology

Nowowiejska 24, Room 132, 00-665 Warsaw, Poland

Phone:  (+48) 22 234 7448, fax: (+48) 22 628 25 87,

E-mail: ame.eo@meil.pw.edu.pl

https://www.editorialsystem.com/ame

www.journals.pan.pl/ame

Instructions for authors

About the Journal
Archive of Mechanical Engineering is an international journal publishing works of wide significance, originality and relevance in most branches of mechanical engineering. The journal is peer-reviewed and is published both in electronic and printed form. Archive of Mechanical Engineering publishes original papers which have not been previously published in other journal, and are not being prepared for publication elsewhere. The publisher will not be held legally responsible should there be any claims for compensation. The journal accepts papers in English.

Archive of Mechanical Engineering is an Open Access journal. The journal does not have article processing charges (APCs) nor article submission charges.

Original high quality papers on the following topics are preferred:

  • Mechanics of Solids and Structures,
  • Fluid Dynamics,
  • Thermodynamics, Heat Transfer and Combustion,
  • Machine Design,
  • Computational Methods in Mechanical Engineering,
  • Robotics, Automation and Control,
  • Mechatronics and Micro-mechanical Systems,
  • Aeronautics and Aerospace Engineering,
  • Heat and Power Engineering.

All submissions to the AME should be made electronically via Editorial System - an online submission and peer review system at: https://www.editorialsystem.com/ame

More detailed instructions for Authors can be found there.

This page uses 'cookies'. Learn more