Applied sciences

Chemical and Process Engineering: New Frontiers

Content

Chemical and Process Engineering | 2012 | No 3 October

Download PDF Download RIS Download Bibtex

Abstract

The possibility of scaling viscoelastic properties of starch solutions in relation to biopolymer concentration was presented in this study. An application of this empirical method enabled to widen the observation horizon of viscoelastic properties. It was also determined that the scope of its applicability is limited by amylose content in the solution. In high amylose solutions, for which up to 40% (w/w) concentration was the highest one obtained, calibration caused the formation of master curve in the widest frequency range. Determined values of scaling coefficients aC changed exponentially in starch concentration function in the solution. For waxy starch solutions of maximum concentration equal to 20% (w/w), scaling did not significantly widen the observation window. Based on master curves constructed in such way, continuous relaxation spectra H(λ) were determined using Tikhonov regularisation method. Their structure indicates advantageous of viscous elements in the process of viscoelastic phenomena formation.

Go to article

Authors and Affiliations

Marcin Łukasiewicz
Paweł Ptaszek
Anna Ptaszek
Mirosław Grzesik
Download PDF Download RIS Download Bibtex

Abstract

The porous structure of cylindrical and ring-shaped char material was developed by partial steam gasification. Micropore and mesopore structures of active carbons with various forms of burn-off were evaluated by nitrogen adsorption/desorption isotherms. Parameters of the Dubinin- Radushkevich equation were calculated as well as the micropore size distribution by the Horvath- Kawazoe method. The results of textural investigations showed that more uniform micropore structure and better mechanical properties were found for ring-shaped active carbons.

Go to article

Authors and Affiliations

Bronisław Buczek
Download PDF Download RIS Download Bibtex

Abstract

The paper presents results of experimental studies on removal of NOx from flue gas via NO ozonation and wet scrubbing of products of NO oxidation in NaOH solutions. The experiment was conducted in a pilot plant installation supplied with flue gas from a coal-fired boiler at the flow rate 200 m3/h. The initial mole fraction of NOx,ref in flue gas was approx. 220 ppm, the molar ratio X = O3/NOref varied between 0 and 2.5. Ozone (O3 content 1÷5% in oxygen) was injected into the flue gas channel before the wet scrubber. The effect of the mole ratio X, the NaOH concentration in the absorbent, the liquid-to-gas ratio (L/G) and the initial NOx concentration on the efficiency of NOx removal was examined. Two domains of the molar ratio X were distinguished in which denitrification was governed by different mechanisms: for X ≤ 1.0 oxidation of NO to NO2 predominates with slow absorption of NO2, for X >> 1.0 NO2 undergoes further oxidation to higher oxides being efficiently absorbed in the scrubber. At the stoichiometric conditions (X = 1) the effectiveness of NO oxidation was better than 90%. However, the effectiveness of NOx removal reached only 25%. When ozonation was intensified (X ≥ 2.25) about 95% of NOx was removed from flue gas. The concentration of sodium hydroxide in the aqueous solution and the liquid-to-gas ratio in the absorber had little effect on the effectiveness of NOx removal for X > 2.

Go to article

Authors and Affiliations

Maciej P. Jakubiak
Włodzimierz K. Kordylewski
Download PDF Download RIS Download Bibtex

Abstract

The article presents tests carried out on three selected samples of limestone originating from three commercially exploited deposits. The tests of sorbents included desulphurisation in different atmospheres and a physicochemical analysis of desulphurisation products. The aim of the tests was to determine desulphurisation efficiency and conversion degree as dependent on the concentration of O2 and CO2.

Go to article

Authors and Affiliations

Angelika Kochel
Aleksandra Cieplińska
Arkadiusz Szymanek
Download PDF Download RIS Download Bibtex

Abstract

The pressure drop in microreactors for the gas - liquid Taylor flow was measured for 4 different microreactor geometries and 3 different gas - liquid systems. The results have been compared with the existing literature correlations. A selection of the best correlations has been made.

Go to article

Authors and Affiliations

Paweł Cygański
Paweł Sobieszuk
Ryszard Pohorecki
Download PDF Download RIS Download Bibtex

Abstract

Some studies show that cells are able to penetrate through pores that are smaller than cell size. It concerns especially Red Blood Cells but it also may concern different types of biological cells. Such penetration of small pores is a very significant problem in the filtration process, for example in micro- or ultrafiltration. Deformability of cells allows them to go through the porous membrane and contaminate permeate. This paper shows how cells can penetrate small cylindrical holes and tries to assess mechanical stress in a cell during this process. A new mathematical approach to this phenomenon was presented, based on assumptions that were made during the microscopic observation of Red Blood Cell aspiration into a small capillary. The computational model concerns Red Blood Cell geometry. The mathematical model allows to obtain geometrical relation as well as mechanical stress relations.

Go to article

Authors and Affiliations

Maciej Szwast
Teresa Suchecka
Wojciech Piątkiewicz
Download PDF Download RIS Download Bibtex

Abstract

The homogeneous stirred reactor designed for kinetic studies of the combustion of hydrocarbons with intensive internal recirculation in high temperature combustion chamber is described. The originality of our reactor lies in its construction which allows to intensively mix fuel and flue gases, measure gas temperature as well as obtain samples which can be used to investigate diffusion flames. The cylindrical construction enables to use the reactor in laboratory cylindrical electrically heated ovens. The CFD analysis of the reactors, the mixing parameters (turbulent Peclet number and mixing level) and the volume average temperature in the reactors were elaborated on the basis of the typical dimensions of classical reactors to kinetics research as well as the own reactor design. The results of the analysis allow to reveal advantages of our construction.

Go to article

Authors and Affiliations

Iwona Gil
Piotr Mocek
Download PDF Download RIS Download Bibtex

Abstract

The application of aqueous two-phase systems (ATPS) is a cost-effective and simple method of protein separation (including enzymes) from complex systems. The first stage of designing the protein purification process in an ATPS involves the identification of the conditions for the formation of a given extraction system. For this purpose, the conditions for the formation of ATPSs in a thermoseparating EO50PO50 polymer/potassium phosphates system have been studied. Factors determining the ATPS formation comprised: separation temperature (4ºC or 20ºC), phosphate solution pH (6, 7.5 or 9) as well as the concentration of NaCl introduced into the systems (0.085 M, 0.475 M and 0.85 M). ATPS without NaCl were prepared as well. The conditions for the formation of the primary EO50PO50/potassium phosphate ATPS were determined with their phase diagrams. It was observed that with an increase of phosphate pH and NaCl concentration in the system, there was a decrease of the EO50PO50 and phosphate concentrations necessary to form a primary ATPS. After the primary two-phase separation, the top phase (rich in the EO50PO50 polymer) was partitioned from the bottom phase (rich in phosphates). Next, by means of polymer phase thermoseparation, a secondary two-phase system was formed. In the secondary EO50PO50/phosphate ATPS, the bottom phase was formed by the concentrated EO50PO50 polymer (30-80% concentration), while the top phase by a solution composed mainly of water, containing phosphate ions and remains of EO50PO50 polymer (3-7%).

Go to article

Authors and Affiliations

Radosław Dembczyński
Wojciech Białas
Tomasz Jankowski
Download PDF Download RIS Download Bibtex

Abstract

Based on hydrodynamic data, Kato-Wen and Kunii-Levenspiel bubbling-bed model parameters, supplemented with assumptions characteristic for tested confined fluidised bed, were analysed. The calculated bubble diameters and the bed composition proved essential influence of inter-particle space of packed compacted component onto fluidisation character. The usability of the conducted model analysis was also confirmed. Finally, it can be concluded that Kunii-Levenspiel and Kato- Wen models with characteristic assumptions (for the tested bed) can be applied for calculation of the confined fluidised bed layer porosity. Discrepancies of ε f value, determined on the basis of the above mentioned bubbling-bed models do not exceed 8% of the error. The model parameters obtained from the matching the model relations to experimental data εf = f(u0) allow an analysis of the fluidisation character as well as gas velocity regime and the fluidised bed structural composition identification. A description of the regime of the process in which confined fluidised bed is characterised with an increase of mass and heat transfer rate is also possible using relation (17) derived in the present study.

Go to article

Authors and Affiliations

Piotr Zabierowski
Download PDF Download RIS Download Bibtex

Abstract

Based on mathematical modelling and numerical simulations, a control strategy for a Molten Carbonate Fuel Cell Hybrid System (MCFC-HS) is presented. Adequate maps of performances with three independent parameters are shown. The independent parameters are as follows: stack current, fuel mass flow and compressor outlet pressure. Those parameters can be controlled by external load, fuel valve and turbine-compressor shaft speed, respectively. The control system is purposed to meet many constraints: e.g. stack temperature, steam-to-carbon ratio, compressor surge limitation, etc. The aim is to achieve maximum efficiency of power generated within these constraints. Governing equations of MCFC-HS modelling are given. An operational line of the MCFC-GT system is presented which fulfils several constraints (temperature difference, cell temperature, etc.) The system is able to achieve efficiency of more than 62% even in part-load operation.

Go to article

Authors and Affiliations

Jarosław Milewski
Andrzej Miller
Download PDF Download RIS Download Bibtex

Abstract

A method of parameters fitting to the experimental vapour - liquid - liquid equilibrium (VLLE) data is presented for the NRTL and the Uniquac equations for six quaternary mixtures. The same equations but with coefficients taken from the simulator Chemcad database were also used for calculation of the VLLE for the same mixtures. The calculated equilibrium temperatures and compositions for all the three phases were compared with the experimental data for these four cases. The investigated models were also applied for calculation of the compositions and temperatures of ternary azeotropes occurring in the considered quaternary mixtures. The computed values were compared with the experimental ones to appreciate the model's accuracy and to confirm whether the model correctly predicts the presence of homo- or heteroazeotrope. The NRTL equation with coefficients fitted to the VLLE data proved to be the most accurate model. For the mixtures containing water, ethanol and two different hydrocarbons this model shows particularly high accuracy. In three cases the mean deviations between the calculated and measured temperatures do not exceed 0.25 K, and for the fourth mixture the difference equals 0.33. Besides, the mean deviations between the calculated and the measured concentrations in the gas and liquid phases, with one exception do not exceed 1 mole %.

Go to article

Authors and Affiliations

Andrzej Wyczesany
Download PDF Download RIS Download Bibtex

Abstract

The paper presents the properties of surface oxide layers with an increased content of carbon for tribological applications. The composite surface oxide layers were produced using a two-step technology through hard anodising of the surface of an aluminium alloy, followed by thermochemical treatment of anodic oxide coatings. The surface oxide layers were subjected to tribological tests in an oil-less sliding couple with T5W plastic. The presented test results confirm the usefulness of the proposed modifications of surface oxide layers for the purpose of enhancing the operational durability of oil-less sliding couples in a reciprocating motion.

Go to article

Authors and Affiliations

Tomasz Kmita
Marek Bara
Download PDF Download RIS Download Bibtex

Abstract

One of the methods of obtaining energy from renewable sources is the technology of indirect cofiring of biomass. It consists in the gasification of secondary fuel and combustion of the generated gas in the boiler together with its primary fuel. The paper presents a thermodynamic analysis of the use of the boiler flue gases as the converting medium in the process of indirect co-firing - a technology which is being developed at the Institute of Power Engineering and Turbomachinery of the Silesian University of Technology. The basis of the analysis are the data resulting from variant calculations conducted with the use of the Gaseq program. The calculations were made for various compositions of gasified fuel and the converting medium, variable fuel/oxidiser ratios and variable gasification temperatures. As a result, the equilibrium composition and the calorific value of the generated gas were obtained. The main optimisation objective adopted here was the nondimensional efficiency coefficient, which is the ratio of the chemical energy of products to the chemical energy of the process reactants.

Go to article

Authors and Affiliations

Rafał Litka
Sylwester Kalisz

Instructions for authors

All manuscripts submitted for publication in Chemical and Process Engineering: New Frontiers must comprise a description of original research that has neither been published nor submitted for publication elsewhere.

The content, aim and scope of the proposals have to comply with the main topics of the journal, i.e. discuss at least one of the four main areas, namely:
• New Advanced (Nano) Materials
• Environment & Water Processing (including circular economy)
• Biochemical & Biomedical Engineering (including pharmaceuticals)
• Climate & Energy (including energy conversion & storage, electrification, decarbonization)

Chemical and Process Engineering: New Frontiers publishes: i) experimental and theoretical research papers, ii) short communications, iii) critical reviews, and iv) perspective articles. Each publication form is peer-reviewed by at least two independent referees.

New Submissions

Manuscripts are submitted for publication via Editorial System. When writing a manuscript, you may choose to submit it as a single Word file to be used in the refereeing process. The manuscript needs to be written in a clear way. The minimum requirements are:
• Please use clear fonts, at least 12 points large, with at least 1.5-line spacing.
• Figures should be placed in relevant places within the manuscript. All figures and tables should be numbered and provided with appropriate caption and legend, if necessary.


Language requirements

• Use Simple Past to talk about your experiment and your results as they were finished before you wrote the paper. Use Simple Past to describe what you did.
Example: Two samples were taken. Temperature increased to 200K at the end of the process.
• Use Simple Present to refer to figures and tables.
Example: Table 2 shows nitrogen concentration changes in the process.
• Use Simple Present to talk about your conclusions. You move here from describing your results to stating what is generally true.
Example: The process is caused by changes of nitrogen concentration.
• Capitalise words like ‘Table 2’, ‘Equation 11’.
• If a sentence is longer than three lines, break down your writing into logically divided parts (paragraphs). Start a new paragraph to discuss a new concept.
• Check noun/verb agreement (singular/plural).
• It is fine to choose either British or American English but you should avoid mixing the two.
• Avoid empty language (it is worth pointing out that, etc.).



Revised Submission

After the first revision, authors will be requested to put their paper in the correct format, using the below guidelines and template for articles.


Manuscript outline

1. Header details
a. Title,
b. Names (first name and further initials) and surnames of authors,
c. Institution(s) (affiliation),
d. Address(es) of authors,
e. ORCID number of all authors.
f. Information about the corresponding author: name and surname, email address.

2. Abstract – should contain a short summary of the proposed paper. In the maximum of 200 words the authors should present the main assumptions, results and conclusions drawn from the presented study.

3. Keywords – up to 5 characteristic keyword items should be provided.

4. Text
a. Introduction. In this part, the rationale for research and formulation of the scientific problem should be included and supported by a concise review of recent literature.
b. Main text. It should contain all important elements of the scientific investigations, such as presentation of experimental setup, mathematical models, results and their discussion. This part may be divided into the following sections: Methods, Results, Discussion.
c. Conclusions. The major conclusions can be put forward in a concise style in a separate chapter. A presentation of conclusions from the reported research work accompanied by a short commentary is also acceptable.
d. Figures: drawings, diagrams and photographs can be in colour and should be located in appropriate places in the manuscript. Their form should be of a vector or raster type with the minimum resolution of 900 dpi. In addition, all figures, including drawings, graphs and photos should be uploaded in a separate file via Editorial System in one of the following formats: bmp, tiff, jpg or eps. For editorial reasons, graphic elements created with MS Word or Excel will not be accepted. They should be saved as image files in the source program. Screen shots will not be accepted. The basic font size of letters used in figures should be at least 10 pts after adjusting graphs to the final size.
e. Tables should be made according to the format shown in the template.
f. All figures and tables should be numbered and provided with an appropriate caption and legend, if necessary. They have to be properly referenced to and commented in the text of the manuscript.

5. List of symbols should be accompanied by their units

6. Acknowledgements may be included before the list of literature references

7. Literature citations
The method of quoting literature source in the manuscript depends on the number of its authors:
single author – their surname and year of publication should be given, e.g. Marquardt (1996) or (Marquardt, 1996),
two authors – the two surnames separated by the conjunction “and” with the publication year should be given, e.g. Charpentier and McKenna (2004) or (Charpentier and McKenna, 2004),
three and more authors – the surname of the first author followed by the abbreviation “et al.” and year of publication should be given, e.g. Bird et al. (1960) or (Bird et al., 1960).

In the case of citing more sources in one bracket, they should be listed in alphabetical order using semicolon for separation, e.g. (Bird et al., 1960; Charpentier and McKenna, 2004; Marquardt, 1996). Should more citations of the same author(s) and year appear in the manuscript then letters “a, b, c, ...” should be successively applied after the publication year.

Bibliographic data of the quoted literature should be arranged at the end of the manuscript in alphabetical order of surnames of the first author. It is obligatory to indicate the DOI number of those literature items, whose numbers have already been assigned. Journal titles should be specified by typing their right abbreviations or, when in doubts, according to the Science and Engineering Journal Abbreviations.

Examples of citation for:

Articles
Charpentier J. C., McKenna T. F., 2004. Managing complex systems: some trends for the future of chemical and process engineering. Chem. Eng. Sci., 59, 1617-1640. DOI: 10.1016/j.ces.2004.01.044.
Information from books (we suggest adding the page numbers where the quoted information can be found)
Bird R. B., Stewart W.E., Lightfood E.N., 2002. Transport Phenomena. 2nd edition, Wiley, New York, 415-421.
Chapters in books
Hanjalić K., Jakirlić S., 2002. Second-moment turbulence closure modelling, In: Launder B.E., Sandham N.D. (Eds.), Closure strategies for turbulent and transitional flows. Cambridge University Press, Cambridge, 47-101.
Conferences
ten Cate A., Bermingham S.K., Derksen J.J., Kramer H.M.J., 2000. Compartmental modeling of an 1100L DTB crystallizer based on Large Eddy flow simulation. 10th European Conference on Mixing. Delft, the Netherlands, 2-5 July 2000, 255-264.



Cover letter


Authors are kindly asked to provide a cover letter which signifies the novelty and most important findings of the manuscript as well as the significance to the field.


Author contributions

During submission, authors will be asked to provide the individual contributions to the paper using the relevant CRediT roles: Conceptualization; Data curation; Formal analysis; Funding acquisition; Investigation; Methodology; Project administration; Resources; Software; Supervision; Validation; Visualization; Roles/Writing - original draft; Writing - review & editing.


Suggested Reviewers

Authors are kindly requested to include a list of 4 potential reviewers for their manuscript, with complete contact information. Suggested reviewers may not reside in the same country as the corresponding author and remain subject to the Editors' discretion in appointing manuscripts for review.


Payments

Starting from 2014 a principle of publishing articles against payment is introduced, assuming non-profit making editorial office. According to the principle, authors or institutions will have to cover the expenses amounting to 1500 PLN netto (excl. VAT) per published article. The above amount will be used to supplement the limited financial means received from the Polish Academy of Sciences for the editorial and publishing expenses. The method of payment will be indicated in an invoice sent to the authors or institutions after acceptance of their manuscripts to be published.

Publication Ethics Policy

ETHICAL PRINCIPLES

Editors of the "Chemical and Process Engineering: New Frontiers" pay attention to maintain ethical standards in scientific publications and undertake any possible measure to counteract neglecting the standards. Papers submitted for publication are evaluated with respect to reliability, conforming to ethical standards and the advancement of science. Principles given below are based on COPE's Best Practice Guidelines for Journal Editors, which may be found at:
http://publicationethics.org/files/u2/Best_Practice.pdf

Authors’ duties

Authorship
Authorship should be limited to persons, who markedly contributed to the idea, project, realization and interpretation of results. All of them have to be listed as co-authors. Other persons, who affected some important parts of the study should be listed or mentioned as co-workers. Author should be certain that all co-authors were enlisted, saw and accepted final version of the paper and agreed upon its publication.

Disclosure and conflict of interests
Author should disclose all sources of financing of his/her study, the input of scientific institutions, associations and other subjects and all important conflicts of interests that might affect results and interpretation of the study.

Standards in reporting
Authors of papers based on original studies should present precise description of performed work and objective discussion on its importance. Source data should be accurately presented in the paper. The paper should contain detailed information and references that would enable others to use it. False or intentionally not true declarations are not ethical and are not accepted by the editors.

Access to and storage of data
Authors may be asked for providing raw data used in the paper for editorial assessment and should be prepared to store them within the reasonable time period after publication.

Multiple, unnecessary and competitive publications
As a rule author should not publish papers describing the same studies in more than one journal or primary publication. Submission of the same paper to more than one journal at the same time is not ethical and prohibited.

Confirmation of sources
Author should cite papers that affected the creation of submitted manuscript and every time he/she should confirm the use of other authors’ work.

Important errors in published papers
When author finds an important error or inaccuracy in his/her paper, he/she is obliged to inform Editorial Office about this as soon as possible.

Originality and plagiarism
Author may submit only original papers. He/she should be certain that the names of authors referred to in the paper and/or fragments of their texts are properly cited or mentioned.

Ghostwriting
Ghost writing/guest authorship are manifestation of scientific unreliability and all such cases will be revealed including notification of appropriate subjects. Signs of scientific unreliability, especially violation of ethical principles in science will be documented by the Editorial Office.


Duties of the Editorial Office


Editors’ duties
Editors know the rules of journal editing including the procedures applied in case of uncovering non-ethical practices.

Decisions on publication
Editor-in Chief is obliged to apply present legal status as to defamation, violation of author’s rights and plagiarism and bears the responsibility for decisions. He/she may consult thematic editors and/or referees in that matter.

Selection of referees
Editorial Office provides appropriate selection of referees and takes care about appropriate course of peer –reviewing (the review has to be substantive).

Confidentiality
Every member of editorial team is not allowed to disclose information about submitted paper to any person except its author, referees, other advisors and editors.

Discrimination
To counteract discrimination the Editorial Office obeys the legally binding rules.

Disclosure and conflict of interests
Not published papers or their fragments cannot be used in the studies of editorial team or ref-erees without written consent of the author.


Referees' duties

Editorial decisions

Referee supports Editor-in-Chief in taking editorial decisions and may also support author in improving the paper.

Back information
In case a selected referee is not able to review the paper or cannot do it in due time period, he/she should inform secretary of the Editorial Office about this fact.

Objectivity standards
Reviews should be objective. Personal criticism is inappropriate. Referees should clearly ex-press their opinions and support them with proper arguments.

Confidentiality
All reviewed papers should be dealt with as confidential. They should not be discussed or revealed to persons other than the secretary of the Editorial Office.

Anonymity
All reviews should be made anonymously and the Editorial Office does not disclose names of the authors to referees.

Disclosure and conflict of interests
Confidential information or ideas resulting from reviewing procedure should be kept secret and should not be used to gain personal benefits. Referees should not review papers, which might generate conflict of interests resulting from relationships with the author, firm or institution involved in the study.

Confirmation of sources
Referees should indicate publications which are not referred to in the paper. Any statement that the observation, source or argument was described previously should be supported by appropriate citation. Referee should also inform the secretary of the Editorial Office about significant similarity to or partial overlapping of the reviewed paper with any other published paper and about suspected plagiarism.



This page uses 'cookies'. Learn more