Nauki Techniczne

Archives of Foundry Engineering

Zawartość

Archives of Foundry Engineering | 2015 | No 4

Abstrakt

The present work focuses on the modeling and analysis of mechanical properties of structural steel. The effect of major alloying elements

namely carbon, manganese and silicon has been investigated on mechanical properties of structural steel. Design of experiments is used to

develop linear models for the responses namely Yield strength, Ultimate tensile strength and Elongation. The experiments have been

conducted as per the full factorial design where all process variables are set at two levels. The main effect plots showed that the alloying

elements Manganese and Silicon have positive contribution on Ultimate tensile strength and Yield strength. However, Carbon and

Manganese showed more contribution as compared to Silicon. All three alloying elements are found to have negative contribution

towards the response- Elongation. The present work is found to be useful to control the mechanical properties of structural steel by varying

the major alloying elements. Minitab software has been used for statistical analysis. The linear regression models have been tested for the

statistical adequacy by utilizing ANOVA and statistical significance test. Further, the prediction capability of the developed models is

tested with the help of test cases. It is found that all linear regression models are found to be statistically adequate with good prediction

capability. The work is useful to foundrymen to choose alloying elements composition to get desirable mechanical properties.

Przejdź do artykułu

Autorzy i Afiliacje

A. Bhatt
M.B. Parappagoudar

Abstrakt

The paper presents the results of research on the determination of the effect of pouring temperature on the macrostructure of the castings

subjected to complex (surface and volume) modification and double filtration. Tested castings were made of post-production scrap (gating

system parts) of IN-713C superalloy. Tests included the evaluation of the number of grains per 1 mm2

, mean grain surface area, shape

factor and tensile strength. Casting temperature below 1470 °C positively influenced the modification effect. The grains were finer and the

mechanical properties increased, especially for castings with thicker walls. On the other hand, manufacture of thin walled castings of high

quality require pouring temperature above 1480 °C.

Przejdź do artykułu

Autorzy i Afiliacje

R. Findziński
P. Gradoń
F. Binczyk
M. Mańka

Abstrakt

Paper presents the assessment of impact of heat treatment on durability in low-cycle fatigue conditions (under constant load) in castings

made using post-production scrap of MAR-247 and IN-713C superalloys. Castings were obtained using modification and filtration

methods. Additionally, casting made of MAR-247 were subjected to heat treatment consisting of solution treatment and subsequent aging.

During low-cycle fatigue test the cyclic creep process were observed. It was demonstrated that the fine-grained samples have significantly

higher durability in test conditions and , at the same time, lower values of plastic deformation to rupture Δϵpl. It has been also proven that

durability of fine-grained MAR-247 samples can be further raised by about 60% using aforementioned heat treatment.

Przejdź do artykułu

Autorzy i Afiliacje

M. Cieśla
G. Junak
P. Gradoń
F. Binczyk
M. Mańka

Abstrakt

Experiments of filling the model moulds cavity of various inner shapes inserted in rectangular cavity of the casting die (dimensions: 280

mm (height) x 190 mm (width) x 10 mm (depth) by applying model liquids of various density and viscosity are presented in the paper.

Influence of die venting as well as inlet system area and inlet velocity on the volumetric rate of filling of the model liquid – achieved by

means of filming the process in the system of a cold-chamber casting die was tested. Experiments compared with the results of simulation

performed by means of the calculation module Novacast (Novaflow&Solid) for the selected various casting conditions – are also

presented in the paper.

Przejdź do artykułu

Autorzy i Afiliacje

R. Dańko
J. Dańko
J. Stojek

Abstrakt

The article shows the influence of environment requirements on changes in different foundry moulding sands technologies such as cold

box, self-hardening moulding sands and green sands. The aim of the article is to show the possibility of using the biodegradable materials

as binders (or parts of binders’ compositions) for foundry moulding and core sands. The authors concentrated on the possibility of

preparing new binders consisting of typical synthetic resins - commonly used in foundry practice - and biodegradable materials. According

to own research it is presumed that using biodegradable materials as a part of new binders’ compositions may cause not only lower toxicity

and better ability to reclaim, but may also accelerate the biodegradation rate of used binders. What’s more, using some kinds of

biodegradable materials may improve flexibility of moulding sands with polymeric binder. The conducted research was introductory and

took into account bending strength and thermal properties of furan moulding sands with biodegradable material (PCL). The research

proved that new biodegradable additive did not decrease the tested properties.

Przejdź do artykułu

Autorzy i Afiliacje

St.M. Dobosz
A. Grabarczyk
K. Major-Gabryś

Abstrakt

The problem considered in the paper is motivated by production planning in a foundry equipped with a furnace and a casting line,

which provides a variety of castings in various grades of cast iron/steel for a large number of customers. The goal is to create the order of

the melted metal loads to prevent delays in delivery of goods to customers. This problem is generally considered as a lot-sizing and

scheduling problem. However, contrary to the classic approach, we assumed the fuzzy nature of the demand set for a given day. The paper

describes a genetic algorithm adapted to take into account the fuzzy parameters of simultaneous grouping and scheduling tasks and

presents the results achieved by the algorithm for example test problem.

Przejdź do artykułu

Autorzy i Afiliacje

J. Duda
A. Stawowy

Abstrakt

The problem related to the management of post reclamation dusts generated in the reclamation process of waste moulding sands with

organic binders is presented in the hereby paper. Waste materials generated in this process are products hazardous for the environment and

should be utilised. The prototype stand for the utilisation of this dangerous material in its co-burning with coal was developed and patented

in AGH in Krakow. The stand was installed in one of the domestic casting houses. As the utilisation result the transformed waste product

is obtained and its management in the production of ceramic materials constitutes the subject of the presented publication.

Przejdź do artykułu

Autorzy i Afiliacje

M. Holtzer
R. Dańko
J. Dańko
Z. Pytel

Abstrakt

The validation of each simulation code used in foundry domain requires individual approach due to its specificity. This validation can by

elaborated on the basis of experimental results or in particular cases by comparison the simulation results from different codes. The article

concerns the influence of grey cast iron density curve and different forms of solid fraction curve Fs=f(T) on the formation of shrinkage

discontinuities. Solid fraction curves applying Newtonian Thermal Analysis (NTA) were estimated. The experimental and numerical

simulation tests were performed on the castings, which were made with Derivative Thermal Analysis (DerTA) standard cups. The

numerical tests were realized using NovaFlow&Solid (NF&S), ProCast and Vulcan codes. In this work, the coupled influence of both

curves on the dynamics of the shrinkage-expansion phenomena and on shrinkage defects prognosis in grey cast iron castings has been

revealed. The final evaluation of the simulation systems usefulness should be based on validation experiment, preceded by comparing the

simulation results of available systems which are proposed in given technology.

Przejdź do artykułu

Autorzy i Afiliacje

Z. Ignaszak
P. Popielarski
J. Hajkowski
E. Codina

Abstrakt

The results of structure observations of Ni base superalloy subjected to long-term influence of high pressure hydrogen atmosphere at 750K

and 850K are presented. The structure investigation were carried out using conventional light-, scanning- (SEM) and transmission electron

microscopy (TEM). The results presented here are supplementary to the mechanical studies given in part I of this investigations. The

results of study concerning mechanical properties degradation and structure observations show that the differences in mechanical

properties of alloy subjected different temperature are caused by more advanced processes of structure degradation during long-term aging

at 850K, compare to that at 750K. Higher service temperature leads to formation of large precipitates of δ phase. The nucleation and

growth of needle- and/or plate-like, relative large delta precipitates proceed probably at expense strengthening γ" phases. Moreover, it can't

be excluded that the least stable γ" phase is replaced with more stable γ' precipitates. TEM observations have disclosed differences in

dislocation structure of alloy aged at 750K and 850K. The dislocation observed in alloy subjected to 750K are were seldom observed only,

while in that serviced at high stress and 850K dislocation array and dislocation cell structure was typical.

Przejdź do artykułu

Autorzy i Afiliacje

M. Kaczorowski
P. Skoczylas
A. Krzyńska

Abstrakt

The paper proposes a methodology useful in verification of results of dilatometric tests aimed at determination of temperatures defining

the start and the end of eutectoid transformation in the course of ductile cast iron cooling, based on quenching techniques and

metallographic examination. For an industrial melt of ductile cast iron, the effect of the rate of cooling after austenitization at temperature

900°C carried out for 30 minutes on temperatures TAr1

start and TAr1

end was determined. The heating rates applied in the study were the

same as the cooling rates and equaled 30, 60, 90, 150, and 300°C/h. It has been found that with increasing cooling rate, values of

temperatures TAr1

start and TAr1

end decrease by several dozen degrees.

Przejdź do artykułu

Autorzy i Afiliacje

A. Trytek
M. Tupaj
M. Mróz
A.W. Orłowicz

Abstrakt

Statistical Process Control (SPC) based on the well known Shewhart control charts, is widely used in contemporary manufacturing

industry, including many foundries. However, the classic SPC methods require that the measured quantities, e.g. process or product

parameters, are not auto-correlated, i.e. their current values do not depend on the preceding ones. For the processes which do not obey this

assumption the Special Cause Control (SCC) charts were proposed, utilizing the residual data obtained from the time-series analysis. In the

present paper the results of application of SCC charts to a green sand processing system are presented. The tests, made on real industrial

data collected in a big iron foundry, were aimed at the comparison of occurrences of out-of-control signals detected in the original data

with those appeared in the residual data. It was found that application of the SCC charts reduces numbers of the signals in almost all cases

It is concluded that it can be helpful in avoiding false signals, i.e. resulting from predictable factors.

Przejdź do artykułu

Autorzy i Afiliacje

M. Perzyk
A. Rodziewicz

Abstrakt

The chosen, typical causes of quality defects of cast-iron „alphin” rings embedded in aluminum cast are being presented in this paper.

Diffusive joint of those inserts with the pistons casts is being used, due to extreme work conditions of destructive influence of the fuel mix

and variable thermo-mechanical loads, which reign in the combustion motor working chamber.

Przejdź do artykułu

Autorzy i Afiliacje

J. Piątkowski
P. Kamiński

Abstrakt

The gas-tungsten arc (GTA) welding behaviors of a magnesium matrix composite reinforced with SiC particles were examined in terms of

microstructure characteristics and process efficiencies. This study focused on the effects of the GTAW process parameters (like welding

current in the range of 100/200 A) on the size of the fusion zone (FZ). The analyses revealed the strong influence of the GTA welding

process on the width and depth of the fusion zone and also on the refinement of the microstructure in the fusion zone. Additionally, the

results of dendrite arm size (DAS) measurements were presented.

Przejdź do artykułu

Autorzy i Afiliacje

E. Przełożyńska
M. Mróz
K.N. Braszczyńska-Malik

Abstrakt

Topic of this work is to compare metalurgy of cast irons poured into sand moulds and into shell molds at IEG Jihlava company and from it

following differencies in structures of thin- and thick-walled castings. This work is dealing with investigation and experimental

measurement on surfaces and sections suitable thin- and thick-walled investment castings at IEG Jihlava. Cast irons with flake graphite

(grey cast iron) and cast irons with spheroidal graphite (ductile cast iron). Both mechanical and physical properties are determined using

calculations from as measured values of wall thicknesses L and Lu, Vickers hardness and remanent magnetism. Measurement results are

discussed, findings are formulated and methods for castings metallurgical quality improvement are recommended finally

Przejdź do artykułu

Autorzy i Afiliacje

B. Skrbek
K. Policar

Abstrakt

The article shows results of studies of primary crystallization and wear resistance of Cr-Ni-Mo cast steel intended for work in corrosive

and abrasive conditions. The studies of primary crystallization were conducted with use of TDA method and modified tester allowing

measurement casting cooling time influence on the cooling and crystallization curves of studied alloys. After heat treatment of examined

cast steel wear tests of the samples were conducted on pin-on-disc type device.

Przejdź do artykułu

Autorzy i Afiliacje

A. Studnicki
M. Kondracki
J. Szajnar
J. Suchoń
M. Gromczyk

Abstrakt

The paper presents the results of hypoeutectic silumin 226 grade and silumin produced on its basis through the addition of V and Mo.

Vanadium and molybdenum were added as the preliminary alloy AlV10 and AlMo8 in an amount providing the concentration of 0.1; 0.2;

0.3 and 0.4% V and Mo. TDA curves of tested silumins were presented; regardless of the chemical composition there were similar thermal

effects. Pressure castings microstructure research revealed the presence in silumins with the addition of V and Mo phases do not occur in

silumin without these additives. These phases have a morphology similar to the walled, and their size increases with increasing

concentration of V and Mo. The size of the precipitates of these phases silumin containing 0.1% V and Mo does not exceed 10 microns,

while 0.4% of the content of these elements increases to about 80 microns. Tests of basic mechanical properties of silumins were carried

out. It has been shown that the highest values of tensile strength Rm = 295 MPa and elongation A = 4.2% have silumin containing

approximately 0.1% V and Mo. Increasing concentrations of these elements causes a gradual lowering of the Rm and A values.

Przejdź do artykułu

Autorzy i Afiliacje

T. Pacyniak
G. Gumienny
T. Szymczak

Abstrakt

A vertical cut at the mid-depth of the 15-ton forging steel ingot has been performed by curtesy of the CELSA – Huta Ostrowiec plant.

Some metallographic studies were able to reveal not only the chilled undersized grains under the ingot surface but columnar grains and

large equiaxed grains as well. Additionally, the structural zone within which the competition between columnar and equiaxed structure

formation was confirmed by metallography study, was also revealed. Therefore, it seemed justified to reproduce some of the observed

structural zones by means of numerical calculation of the temperature field. The formation of the chilled grains zone is the result of

unconstrained rapid solidification and was not subject of simulation. Contrary to the equiaxed structure formation, the columnar structure

or columnar branched structure formation occurs under steep thermal gradient. Thus, the performed simulation is able to separate both

discussed structural zones and indicate their localization along the ingot radius as well as their appearance in term of solidification time.

Przejdź do artykułu

Autorzy i Afiliacje

W. Skuza
B. Kania
P. Kwapisiński
W. Wołczyński
A.W. Bydałek
W. Wajda

Abstrakt

This study summarises the research efforts undertaken in iron foundry plants in which the process are mostly automated and mechanised.

The research program was limited in scope, focusing on causes of surface defects in castings products that are attributable to the

bentonite-containing sand and the mould system. One of the potential roots of surface defects is heterogeneity of sand grains, containing

lumped ball-shaped grains and irregular pellets with a layered-structure. The moisture contents of those lumped grains is different than

the moisture level required in the process, besides these grains may contain various elements and metallic compounds which, when cast

into moulds, may react with molten metals in an uncontrolled manner. As a result, surface defects are produced, such as surface blowholes,

burst penetration, sand holes, slag inclusions, pinhole porosity. This study investigated the efficiency of key sand preparation and

moulding machines and installations integrated into the casting process line. The efficiency of machines and installations is defined in

terms of quality parameters of sand mix and moulds, which are associated with the emergence of surface defects on castings.

Przejdź do artykułu

Autorzy i Afiliacje

R. Wrona
E. Ziółkowski
M. Brzeziński

Abstrakt

The obtained results of heating of sand moulds with binders by means of a thermal radiation of liquid metal are presented in this study.

Standard samples for measuring Rg made of the tested moulding sands were suspended at the lower part of the cover which was covering

the crucible with liquid metal (cast iron), placed in the induction furnace. The authors own methodology was applied in investigations. The

progressing of the samples surface layers heating process was determined as the heating time function. Samples of a few kinds of

moulding sands with chemical binders were tested. Samples without protective coatings as well as samples with such coatings were tested.

The influence of the thermal radiation on bending resistance of samples after their cooling was estimated. The influence of several

parameters such as: time of heating, distance from the metal surface, metal temperature, application of coatings, were tested. A very fast

loss of strength of moulding sands with organic binders was found, especially in cases when the distance between metal and sample

surfaces was small and equaled to 10÷15 mm. Then, already after app. 15 seconds of the radiation (at Tmet=1400o

C), the resistance

decreases by nearly 70%. Generally, moulding sands with organic binders are losing their strength very fast, while moulding sands with

water glass at first increase their strength and later slightly lose. The deposition of protective coatings increases the strength of the mould

surface layers, however does not allow to retain this strength after the metal thermal radiation.

Przejdź do artykułu

Autorzy i Afiliacje

J. Zych
J. Mocek

Abstrakt

Solidification of AlSiFe alloys was studied using a directional solidification facility and the CALPHAD technique was applied to calculate

phase diagrams and to predict occurring phases. The specimens solidified by electromagnetic stirring showed segregation across, and the

measured chemical compositions were transferred into phase diagrams. The ternary phase diagrams presented different solidification paths

caused by segregation in each selected specimen. The property diagrams showed modification in the sequence and precipitation

temperature of the phases. It is proposed in the study to use thermodynamic calculations with Thermo-Calc which enables us to visualize

the mushy zone in directional solidification. 2D maps based on property diagrams show a mushy zone with a liquid channel in the

AlSi7Fe1.0 specimen center, where significant mass fraction (33%) of β-Al5FeSi phases may precipitate before α-Al dendrites form.

Otherwise liquid channel occurred almost empty of β in AlSi7Fe0.5 specimen and completely without β in AlSi9Fe0.2. The property

diagrams revealed also possible formation of α–Al8Fe2Si phases.

Przejdź do artykułu

Autorzy i Afiliacje

P. Mikołajczak
L. Ratke

Abstrakt

Achieving control of coating thickness in foundry moulds is needed in order to guarantee uniform properties of the mould but also to

achieve control of drying time. Since drying time of water based coatings is heavily dependent on the amount of water present in the

coating layer, a stable coating process is prerequisite for a stable drying process. In this study, we analyse the effect of different variables

on the coating layer properties. We start by considering four critical variables identified in a previous study such as sand compaction,

coating density, dipping time and gravity and then we add centre points to the original experimental plans to identify possible non-linear

effects and variation in process stability. Finally, we investigate the relation between coating penetration (a variable that is relatively

simple to measure in production) and other coating layer thickness properties (relevant for the drying process design). Correlations are

found and equations are provided. In particular it is found that water thickness can be directly correlated to penetration with a simple linear

equation and without the need to account for other variables.

Przejdź do artykułu

Autorzy i Afiliacje

G.L. Di Muoio
N.S. Tiedje

Abstrakt

Turbine blades have complex geometries with free form surface. Blades have different thickness at the trailing and leading edges as well

as sharp bends at the chord-tip shroud junction and sharp fins at the tip shroud. In investment casting of blades, shrinkage at the tip-shroud

and cord junction is a common casting problem. Because of high temperature applications, grain structure is also critical in these castings

in order to avoid creep. The aim of this work is to evaluate the effect of different process parameters, such as, shell thickness, insulation

and casting temperature on shrinkage porosity and grain size. The test geometry used in this study was a thin-walled air-foil structure

which is representative of a typical hot-gas-path rotating turbine component. It was observed that, in thin sections, increased shell

thickness helps to increase the feeding distance and thus avoid interdendritic shrinkage. It was also observed that grain size is not

significantly affected by shell thickness in thin sections. Slower cooling rate due to the added insulation and steeper thermal gradient at

metal mold interface induced by the thicker shell not only helps to avoid shrinkage porosity but also increases fill-ability in thinner

sections.

Przejdź do artykułu

Autorzy i Afiliacje

M. Raza
M. Irwin
B. Fagerström

Abstrakt

At thermal junctions of aluminium alloy castings and at points where risering proves to be difficult there appear internal or external

shrinkages, which are both functionally and aesthetically inadmissible. Applying the Probat Fluss Mikro 100 agent, which is based on

nano-oxides of aluminium, results in the appearance of a large amount of fine microscopic pores, which compensate for the shrinking of

metal. Experimental tests with gravity die casting of AlSi8Cu3 and AlSi10Mg alloys have confirmed that the effect of the agent can be of

advantage in foundry practice, leading to the production of castings without local concentrations of defects and without the appearance of

shrinkages and macroscopic gas pores. Also, beneficial effect on the mechanical properties of the metal has been observed.

Przejdź do artykułu

Autorzy i Afiliacje

J. Roučka
J. Hotař

Abstrakt

Cast Hadfield steel is characterised by high abrasion resistance, provided, however, that it is exposed to the effect of dynamic loads.

During abrasion without loading, e.g. under the impact of loose sand jet, its wear resistance drops very drastically. To increase the abrasion

resistance of this alloy under the conditions where no pressure is acting, primary vanadium carbides are formed in the metallurgical

process, to obtain a composite structure after the melt solidification. The primary, very hard, carbides uniformly distributed in the

austenitic matrix are reported to double the wear resistance of samples subjected to the effect of a silicon carbide-water mixture.

Przejdź do artykułu

Autorzy i Afiliacje

G. Tęcza
J. Głownia

Abstrakt

The formation of oxide film on the surface of aluminium melts, i.e. bifilms, are known to be detrimental when they are incorporated into

the cast part. These defects causes premature fractures under stress, or aid porosity formation. In this work, Al-12 Si alloy was used to cast

a step mould under two conditions: as-received and degassed. In addition, 10 ppi filters were used in the mould in order to prevent bifilm

intrusion into the cast part. Reduced pressure test samples were collected for bifilm index measurements. Samples were machined into

standard bars for tensile testing. It was found that there was a good agreement with the bifilm index and mechanical properties.

Przejdź do artykułu

Autorzy i Afiliacje

F. Yilmaz
M. Uludağ
M. Uyaner
D. Dişpinar

Instrukcja dla autorów

Submission


To submit the article, please use the Editorial System provided here:

https://www.editorialsystem.com/afe


Papers submitted in any other way will not be accepted.



The Journal does not have submission charges.


The APC Article Processing Charge is 110 euros (500zł for Polish authors). In some cases, the APC is paid as a part of the scientific conference fee, for which the AFE journal is a supportive one. If not, it is payable after the acceptance of the final article by direct money transfer.


Bank account details:


Account holder: Stowarzyszenie Wychowankow Politechniki Slaskiej Kolo Odlewnikow
Account holder address: ul. Towarowa 7, 44-100 Gliwice, Poland
Account numbers: BIC BPKOPLPW IBAN PL17 1020 2401 0000 0202 0183 3748


Instructions for the preparation of an Archives of Foundry Engineering Paper

Zasady etyki publikacyjnej


Publication Ethics Policy

The standards of expected ethical behavior for all parties involved in publishing in the Archives of Foundry Engineering journal: the author, the journal editor and editorial board, the peer reviewers and the publisher are listed below.

All the articles submitted for publication in Archives of Foundry Engineering are peer reviewed for authenticity, ethical issues and usefulness as per Review Procedure document.

Duties of Editors
1. Monitoring the ethical standards: Editorial Board monitors the ethical standards of the submitted manuscripts and takes all possible measures against any publication malpractices.
2. Fair play: Submitted manuscripts are evaluated for their scientific content without regard to race, gender, sexual orientation, religious beliefs, citizenship, political ideology or any other issues that is a personal or human right.
3. Publication decisions: The Editor in Chief is responsible for deciding which of the submitted articles should or should not be published. The decision to accept or reject the article is based on its importance, originality, clarity, and its relevance to the scope of the journal and is made after the review process.
4. Confidentiality: The Editor in Chief and the members of the Editorial Board t ensure that all materials submitted to the journal remain confidential during the review process. They must not disclose any information about a submitted manuscript to anyone other than the parties involved in the publishing process i.e., authors, reviewers, potential reviewers, other editorial advisers, and the publisher.
5. Disclosure and conflict of interest: Unpublished materials disclosed in the submitted manuscript must not be used by the Editor and the Editorial Board in their own research without written consent of authors. Editors always precludes business needs from compromising intellectual and ethical standards.
6. Maintain the integrity of the academic record: The editors will guard the integrity of the published academic record by issuing corrections and retractions when needed and pursuing suspected or alleged research and publication misconduct. Plagiarism and fraudulent data is not acceptable. Editorial Board always be willing to publish corrections, clarifications, retractions and apologies when needed.

Retractions of the articles: the Editor in Chief will consider retracting a publication if:
- there are clear evidences that the findings are unreliable, either as a result of misconduct (e.g. data fabrication) or honest error (e.g. miscalculation or experimental error)
- the findings have previously been published elsewhere without proper cross-referencing, permission or justification (cases of redundant publication)
- it constitutes plagiarism or reports unethical research.
Notice of the retraction will be linked to the retracted article (by including the title and authors in the retraction heading), clearly identifies the retracted article and state who is retracting the article. Retraction notices should always mention the reason(s) for retraction to distinguish honest error from misconduct.
Retracted articles will not be removed from printed copies of the journal nor from electronic archives but their retracted status will be indicated as clearly as possible.

Duties of Authors
1. Reporting standards: Authors of original research should present an accurate account of the work performed as well as an objective discussion of its significance. Underlying data should be represented accurately in the paper. The paper should contain sufficient details and references to permit others to replicate the work. The fabrication of results and making of fraudulent or inaccurate statements constitute unethical behavior and will cause rejection or retraction of a manuscript or a published article.
2. Originality and plagiarism: Authors should ensure that they have written entirely original works, and if the authors have used the work and/or words of others they need to be cited or quoted. Plagiarism and fraudulent data is not acceptable.
3. Data access retention: Authors may be asked to provide the raw data for editorial review, should be prepared to provide public access to such data, and should be prepared to retain such data for a reasonable time after publication of their paper.
4. Multiple or concurrent publication: Authors should not in general publish a manuscript describing essentially the same research in more than one journal. Submitting the same manuscript to more than one journal concurrently constitutes unethical publishing behavior and is unacceptable.
5. Authorship of the manuscript: Authorship should be limited to those who have made a significant contribution to the conception, design, execution, or interpretation of the report study. All those who have made contributions should be listed as co-authors. The corresponding author should ensure that all appropriate co-authors and no inappropriate co-authors are included in the paper, and that all co-authors have seen and approved the final version of the paper and have agreed to its submission for publication.
6. Acknowledgement of sources: The proper acknowledgment of the work of others must always be given. The authors should cite publications that have been influential in determining the scope of the reported work.
7. Fundamental errors in published works: When the author discovers a significant error or inaccuracy in his/her own published work, it is the author’s obligation to promptly notify the journal editor or publisher and cooperate with the editor to retract or correct the paper.

Duties of Reviewers
1. Contribution to editorial decisions: Peer reviews assist the editor in making editorial decisions and may also help authors to improve their manuscript.
2. Promptness: Any selected reviewer who feels unqualified to review the research reported in a manuscript or knows that its timely review will be impossible should notify the editor and excuse himself/herself from the review process.
3. Confidentiality: All manuscript received for review must be treated as confidential documents. They must not be shown to or discussed with others except those authorized by the editor.
4. Standards of objectivity: Reviews should be conducted objectively. Personal criticism of the author is inappropriate. Reviewers should express their views clearly with appropriate supporting arguments.
5. Acknowledgement of sources: Reviewers should identify the relevant published work that has not been cited by authors. Any substantial similarity or overlap between the manuscript under consideration and any other published paper should be reported to the editor.
6. Disclosure and conflict of Interest: Privileged information or ideas obtained through peer review must be kept confidential and not used for personal advantage. Reviewers should not consider evaluating manuscripts in which they have conflicts of interest resulting from competitive, collaborative, or other relations with any of the authors, companies, or institutions involved in writing a paper.

Procedura recenzowania


Review Procedure


The Review Procedure for articles submitted to the Archives of Foundry Engineering agrees with the recommendations of the Ministry of Science and Higher Education published in a booklet: ‘Dobre praktyki w procedurach recenzyjnych w nauce’ (MNiSW, Dobre praktyki w procedurach recenzyjnych w nauce, Warszawa 2011).

Papers submitted to the Editorial System are primarily screened by editors with respect to scope, formal issues and used template. Texts with obvious errors (formatting other than requested, missing references, evidently low scientific quality) will be rejected at this stage or will be sent for the adjustments.

Once verified each article is checked by the anti-plagiarism system Cross Check powered by iThenticate®. After the positive response, the article is moved into: Initially verified manuscripts. When the similarity level is too high, the article will be rejected. There is no strict rule (i.e., percentage of the similarity), and it is always subject to the Editor’s decision.
Initially verified manuscripts are then sent to at least four independent referees outside the author’s institution and at least two of them outside of Poland, who:

have no conflict of interests with the author,
are not in professional relationships with the author,
are competent in a given discipline and have at least a doctorate degree and respective
scientific achievements,
have a good reputation as reviewers.


The review form is available online at the Journal’s Editorial System and contains the following sections:

1. Article number and title in the Editorial System

2. The statement of the Reviewer (to choose the right options):

I declare that I have not guessed the identity of the Author. I declare that I have guessed the identity of the Author, but there is no conflict of interest

3. Detailed evaluation of the manuscript against other researches published to this point:

Do you think that the paper title corresponds with its contents?
Yes No
Do you think that the abstract expresses the paper contents well?
Yes No
Are the results or methods presented in the paper novel?
Yes No
Do the author(s) state clearly what they have achieved?
Yes No
Do you find the terminology employed proper?
Yes No
Do you find the bibliography representative and up-to-date?
Yes No
Do you find all necessary illustrations and tables?
Yes No
Do you think that the paper will be of interest to the journal readers?
Yes No

4. Reviewer conclusion

Accept without changes
Accept after changes suggested by reviewer.
Rate manuscript once again after major changes and another review
Reject


5. Information for Editors (not visible for authors).

6. Information for Authors


Reviewing is carried out in the double blind process (authors and reviewers do not know each other’s names).

The appointed reviewers obtain summary of the text and it is his/her decision upon accepting/rejecting the paper for review within a given time period 21 days.

The reviewers are obliged to keep opinions about the paper confidential and to not use knowledge about it before publication.

The reviewers send their review to the Archives of Foundry Engineering by Editorial System. The review is archived in the system.

Editors do not accept reviews, which do not conform to merit and formal rules of scientific reviewing like short positive or negative remarks not supported by a close scrutiny or definitely critical reviews with positive final conclusion. The reviewer’s remarks are sent to the author. He/she has to consider all remarks and revise the text accordingly.

The author of the text has the right to comment on the conclusions in case he/she does not agree with them. He/she can request the article withdrawal at any step of the article processing.

The Editor-in-Chief (supported by members of the Editorial Board) decides on publication based on remarks and conclusions presented by the reviewers, author’s comments and the final version of the manuscript.

The final Editor’s decision can be as follows:
Accept without changes
Reject


The rules for acceptance or rejection of the paper and the review form are available on the Web page of the AFE publisher.

Once a year Editorial Office publishes present list of cooperating reviewers.
Reviewing is free of charge.
All articles, including those rejected and withdrawn, are archived in the Editorial System.

Recenzenci

List of Reviewers 2022

Shailee Acharya - S. V. I. T Vasad, India
Vivek Ayar - Birla Vishvakarma Mahavidyalaya Vallabh Vidyanagar, India
Mohammad Azadi - Semnan University, Iran
Azwinur Azwinur - Politeknik Negeri Lhokseumawe, Indonesia
Czesław Baron - Silesian University of Technology, Gliwice, Poland
Dariusz Bartocha - Silesian University of Technology, Gliwice, Poland
Iwona Bednarczyk - Silesian University of Technology, Gliwice, Poland
Artur Bobrowski - AGH University of Science and Technology, Kraków
Poland Łukasz Bohdal - Koszalin University of Technology, Koszalin Poland
Danka Bolibruchova - University of Zilina, Slovak Republic
Joanna Borowiecka-Jamrozek- The Kielce University of Technology, Poland
Debashish Bose - Metso Outotec India Private Limited, Vadodara, India
Andriy Burbelko - AGH University of Science and Technology, Kraków
Poland Ganesh Chate - KLS Gogte Institute of Technology, India
Murat Çolak - Bayburt University, Turkey
Adam Cwudziński - Politechnika Częstochowska, Częstochowa, Poland
Derya Dispinar- Istanbul Technical University, Turkey
Rafał Dojka - ODLEWNIA RAFAMET Sp. z o. o., Kuźnia Raciborska, Poland
Anna Dolata - Silesian University of Technology, Gliwice, Poland
Tomasz Dyl - Gdynia Maritime University, Gdynia, Poland
Maciej Dyzia - Silesian University of Technology, Gliwice, Poland
Eray Erzi - Istanbul University, Turkey
Flora Faleschini - University of Padova, Italy
Imre Felde - Obuda University, Hungary
Róbert Findorák - Technical University of Košice, Slovak Republic
Aldona Garbacz-Klempka - AGH University of Science and Technology, Kraków, Poland
Katarzyna Gawdzińska - Maritime University of Szczecin, Poland
Marek Góral - Rzeszow University of Technology, Poland
Barbara Grzegorczyk - Silesian University of Technology, Gliwice, Poland
Grzegorz Gumienny - Technical University of Lodz, Poland
Ozen Gursoy - University of Padova, Italy
Gábor Gyarmati - University of Miskolc, Hungary
Jakub Hajkowski - Poznan University of Technology, Poland
Marek Hawryluk - Wroclaw University of Science and Technology, Poland
Aleš Herman - Czech Technical University in Prague, Czech Republic
Mariusz Holtzer - AGH University of Science and Technology, Kraków, Poland
Małgorzata Hosadyna-Kondracka - Łukasiewicz Research Network - Krakow Institute of Technology, Poland
Dario Iljkić - University of Rijeka, Croatia
Magdalena Jabłońska - Silesian University of Technology, Gliwice, Poland
Nalepa Jakub - Silesian University of Technology, Gliwice, Poland
Jarosław Jakubski - AGH University of Science and Technology, Kraków, Poland
Aneta Jakubus - Akademia im. Jakuba z Paradyża w Gorzowie Wielkopolskim, Poland
Łukasz Jamrozowicz - AGH University of Science and Technology, Kraków, Poland
Krzysztof Janerka - Silesian University of Technology, Gliwice, Poland
Karolina Kaczmarska - AGH University of Science and Technology, Kraków, Poland
Jadwiga Kamińska - Łukasiewicz Research Network – Krakow Institute of Technology, Poland
Justyna Kasinska - Kielce University Technology, Poland
Magdalena Kawalec - AGH University of Science and Technology, Kraków, Poland
Gholamreza Khalaj - Islamic Azad University, Saveh Branch, Iran
Angelika Kmita - AGH University of Science and Technology, Kraków, Poland
Marcin Kondracki - Silesian University of Technology, Gliwice Poland
Vitaliy Korendiy - Lviv Polytechnic National University, Lviv, Ukraine
Aleksandra Kozłowska - Silesian University of Technology, Gliwice, Poland
Ivana Kroupová - VSB - Technical University of Ostrava, Czech Republic
Malgorzata Lagiewka - Politechnika Czestochowska, Częstochowa, Poland
Janusz Lelito - AGH University of Science and Technology, Kraków, Poland
Jingkun Li - University of Science and Technology Beijing, China
Petr Lichy - Technical University Ostrava, Czech Republic
Y.C. Lin - Central South University, China
Mariusz Łucarz - AGH University of Science and Technology, Kraków, Poland
Ewa Majchrzak - Silesian University of Technology, Gliwice, Poland
Barnali Maji - NIT-Durgapur: National Institute of Technology, Durgapur, India
Pawel Malinowski - AGH University of Science and Technology, Kraków, Poland
Marek Matejka - University of Zilina, Slovak Republic
Bohdan Mochnacki - Technical University of Occupational Safety Management, Katowice, Poland
Grzegorz Moskal - Silesian University of Technology, Poland
Kostiantyn Mykhalenkov - National Academy of Science of Ukraine, Ukraine
Dawid Myszka - Silesian University of Technology, Gliwice, Poland
Maciej Nadolski - Czestochowa University of Technology, Poland
Krzysztof Naplocha - Wrocław University of Science and Technology, Poland
Daniel Nowak - Wrocław University of Science and Technology, Poland
Tomáš Obzina - VSB - Technical University of Ostrava, Czech Republic
Peiman Omranian Mohammadi - Shahid Bahonar University of Kerman, Iran
Zenon Opiekun - Politechnika Rzeszowska, Rzeszów, Poland
Onur Özbek - Duzce University, Turkey
Richard Pastirčák - University of Žilina, Slovak Republic
Miroslawa Pawlyta - Silesian University of Technology, Gliwice, Poland
Jacek Pezda - ATH Bielsko-Biała, Poland
Bogdan Piekarski - Zachodniopomorski Uniwersytet Technologiczny, Szczecin, Poland
Jacek Pieprzyca - Silesian University of Technology, Gliwice, Poland
Bogusław Pisarek - Politechnika Łódzka, Poland
Marcela Pokusová - Slovak Technical University in Bratislava, Slovak Republic
Hartmut Polzin - TU Bergakademie Freiberg, Germany
Cezary Rapiejko - Lodz University of Technology, Poland
Arron Rimmer - ADI Treatments, Doranda Way, West Bromwich, West Midlands, United Kingdom
Jaromír Roučka - Brno University of Technology, Czech Republic
Charnnarong Saikaew - Khon Kaen University Thailand Amit Sata - MEFGI, Faculty of Engineering, India
Mariola Saternus - Silesian University of Technology, Gliwice, Poland
Vasudev Shinde - DKTE' s Textile and Engineering India Robert Sika - Politechnika Poznańska, Poznań, Poland
Bozo Smoljan - University North Croatia, Croatia
Leszek Sowa - Politechnika Częstochowska, Częstochowa, Poland
Sławomir Spadło - Kielce University of Technology, Poland
Mateusz Stachowicz - Wroclaw University of Technology, Poland
Marcin Stawarz - Silesian University of Technology, Gliwice, Poland
Grzegorz Stradomski - Czestochowa University of Technology, Poland
Roland Suba - Schaeffler Skalica, spol. s r.o., Slovak Republic
Maciej Sułowski - AGH University of Science and Technology, Kraków, Poland
Jan Szajnar - Silesian University of Technology, Gliwice, Poland
Michal Szucki - TU Bergakademie Freiberg, Germany
Tomasz Szymczak - Lodz University of Technology, Poland
Damian Słota - Silesian University of Technology, Gliwice, Poland
Grzegorz Tęcza - AGH University of Science and Technology, Kraków, Poland
Marek Tkocz - Silesian University of Technology, Gliwice, Poland
Andrzej Trytek - Rzeszow University of Technology, Poland
Mirosław Tupaj - Rzeszow University of Technology, Poland
Robert B Tuttle - Western Michigan University United States Seyed Ebrahim Vahdat - Ayatollah Amoli Branch, Islamic Azad University, Amol, Iran
Iveta Vaskova - Technical University of Kosice, Slovak Republic
Dorota Wilk-Kołodziejczyk - AGH University of Science and Technology, Kraków, Poland
Ryszard Władysiak - Lodz University of Technology, Poland
Çağlar Yüksel - Atatürk University, Turkey
Renata Zapała - AGH University of Science and Technology, Kraków, Poland
Jerzy Zych - AGH University of Science and Technology, Kraków, Poland
Andrzej Zyska - Czestochowa University of Technology, Poland



List of Reviewers 2021

Czesław Baron - Silesian University of Technology, Gliwice, Poland
Imam Basori - State University of Jakarta, Indonesia
Leszek Blacha - Silesian University of Technology, Gliwice
Poland Artur Bobrowski - AGH University of Science and Technology, Kraków, Poland
Danka Bolibruchova - University of Zilina, Slovak Republic
Pedro Brito - Pontifical Catholic University of Minas Gerais, Brazil
Marek Bruna - University of Zilina, Slovak Republic
Marcin Brzeziński - AGH University of Science and Technology, Kraków, Poland
Andriy Burbelko - AGH University of Science and Technology, Kraków, Poland
Alexandros Charitos - TU Bergakademie Freiberg, Germany
Ganesh Chate - KLS Gogte Institute of Technology, India
L.Q. Chen - Northeastern University, China
Zhipei Chen - University of Technology, Netherlands
Józef Dańko - AGH University of Science and Technology, Kraków, Poland
Brij Dhindaw - Indian Institute of Technology Bhubaneswar, India
Derya Dispinar - Istanbul Technical University, Turkey
Rafał Dojka - ODLEWNIA RAFAMET Sp. z o. o., Kuźnia Raciborska, Poland
Anna Dolata - Silesian University of Technology, Gliwice, Poland
Agnieszka Dulska - Silesian University of Technology, Gliwice, Poland
Maciej Dyzia - Silesian University of Technology, Poland
Eray Erzi - Istanbul University, Turkey
Przemysław Fima - Institute of Metallurgy and Materials Science PAN, Kraków, Poland
Aldona Garbacz-Klempka - AGH University of Science and Technology, Kraków, Poland
Dipak Ghosh - Forace Polymers P Ltd., India
Beata Grabowska - AGH University of Science and Technology, Kraków, Poland
Adam Grajcar - Silesian University of Technology, Gliwice, Poland
Grzegorz Gumienny - Technical University of Lodz, Poland
Gábor Gyarmati - Foundry Institute, University of Miskolc, Hungary
Krzysztof Herbuś - Silesian University of Technology, Gliwice, Poland
Aleš Herman - Czech Technical University in Prague, Czech Republic
Mariusz Holtzer - AGH University of Science and Technology, Kraków, Poland
Małgorzata Hosadyna-Kondracka - Łukasiewicz Research Network - Krakow Institute of Technology, Kraków, Poland
Jarosław Jakubski - AGH University of Science and Technology, Kraków, Poland
Krzysztof Janerka - Silesian University of Technology, Gliwice, Poland
Robert Jasionowski - Maritime University of Szczecin, Poland
Agata Jażdżewska - Gdansk University of Technology, Poland
Jan Jezierski - Silesian University of Technology, Gliwice, Poland
Karolina Kaczmarska - AGH University of Science and Technology, Kraków, Poland
Jadwiga Kamińska - Centre of Casting Technology, Łukasiewicz Research Network – Krakow Institute of Technology, Poland
Adrian Kampa - Silesian University of Technology, Gliwice, Poland
Wojciech Kapturkiewicz- AGH University of Science and Technology, Kraków, Poland
Tatiana Karkoszka - Silesian University of Technology, Gliwice, Poland
Gholamreza Khalaj - Islamic Azad University, Saveh Branch, Iran
Himanshu Khandelwal - National Institute of Foundry & Forging Technology, Hatia, Ranchi, India
Angelika Kmita - AGH University of Science and Technology, Kraków, Poland
Grzegorz Kokot - Silesian University of Technology, Gliwice, Poland
Ladislav Kolařík - CTU in Prague, Czech Republic
Marcin Kondracki - Silesian University of Technology, Gliwice, Poland
Dariusz Kopyciński - AGH University of Science and Technology, Kraków, Poland
Janusz Kozana - AGH University of Science and Technology, Kraków, Poland
Tomasz Kozieł - AGH University of Science and Technology, Kraków, Poland
Aleksandra Kozłowska - Silesian University of Technology, Gliwice Poland
Halina Krawiec - AGH University of Science and Technology, Kraków, Poland
Ivana Kroupová - VSB - Technical University of Ostrava, Czech Republic
Wacław Kuś - Silesian University of Technology, Gliwice, Poland
Jacques Lacaze - University of Toulouse, France
Avinash Lakshmikanthan - Nitte Meenakshi Institute of Technology, India
Jaime Lazaro-Nebreda - Brunel Centre for Advanced Solidification Technology, Brunel University London, United Kingdom
Janusz Lelito - AGH University of Science and Technology, Kraków, Poland
Tomasz Lipiński - University of Warmia and Mazury in Olsztyn, Poland
Mariusz Łucarz - AGH University of Science and Technology, Kraków, Poland
Maria Maj - AGH University of Science and Technology, Kraków, Poland
Jerzy Mendakiewicz - Silesian University of Technology, Gliwice, Poland
Hanna Myalska-Głowacka - Silesian University of Technology, Gliwice, Poland
Kostiantyn Mykhalenkov - Physics-Technological Institute of Metals and Alloys, National Academy of Science of Ukraine, Ukraine
Dawid Myszka - Politechnika Warszawska, Warszawa, Poland
Maciej Nadolski - Czestochowa University of Technology, Poland
Daniel Nowak - Wrocław University of Science and Technology, Poland
Mitsuhiro Okayasu - Okayama University, Japan
Agung Pambudi - Sebelas Maret University in Indonesia, Indonesia
Richard Pastirčák - University of Žilina, Slovak Republic
Bogdan Piekarski - Zachodniopomorski Uniwersytet Technologiczny, Szczecin, Poland
Bogusław Pisarek - Politechnika Łódzka, Poland
Seyda Polat - Kocaeli University, Turkey
Hartmut Polzin - TU Bergakademie Freiberg, Germany
Alena Pribulova - Technical University of Košice, Slovak Republic
Cezary Rapiejko - Lodz University of Technology, Poland
Arron Rimmer - ADI Treatments, Doranda Way, West Bromwich West Midlands, United Kingdom
Iulian Riposan - Politehnica University of Bucharest, Romania
Ferdynand Romankiewicz - Uniwersytet Zielonogórski, Zielona Góra, Poland
Mario Rosso - Politecnico di Torino, Italy
Jaromír Roučka - Brno University of Technology, Czech Republic
Charnnarong Saikaew - Khon Kaen University, Thailand
Mariola Saternus - Silesian University of Technology, Gliwice, Poland
Karthik Shankar - Amrita Vishwa Vidyapeetham , Amritapuri, India
Vasudev Shinde - Shivaji University, Kolhapur, Rajwada, Ichalkaranji, India
Robert Sika - Politechnika Poznańska, Poznań, Poland
Jerzy Sobczak - AGH University of Science and Technology, Kraków, Poland
Sebastian Sobula - AGH University of Science and Technology, Kraków, Poland
Marek Soiński - Akademia im. Jakuba z Paradyża w Gorzowie Wielkopolskim, Poland
Mateusz Stachowicz - Wroclaw University of Technology, Poland
Marcin Stawarz - Silesian University of Technology, Gliwice, Poland
Andrzej Studnicki - Silesian University of Technology, Gliwice, Poland
Mayur Sutaria - Charotar University of Science and Technology, CHARUSAT, Gujarat, India
Maciej Sułowski - AGH University of Science and Technology, Kraków, Poland
Sutiyoko Sutiyoko - Manufacturing Polytechnic of Ceper, Klaten, Indonesia
Tomasz Szymczak - Lodz University of Technology, Poland
Marek Tkocz - Silesian University of Technology, Gliwice, Poland
Andrzej Trytek - Rzeszow University of Technology, Poland
Jacek Trzaska - Silesian University of Technology, Gliwice, Poland
Robert B Tuttle - Western Michigan University, United States
Muhammet Uludag - Selcuk University, Turkey
Seyed Ebrahim Vahdat - Ayatollah Amoli Branch, Islamic Azad University, Amol, Iran
Tomasz Wrobel - Silesian University of Technology, Gliwice, Poland
Ryszard Władysiak - Lodz University of Technology, Poland
Antonin Zadera - Brno University of Technology, Czech Republic
Renata Zapała - AGH University of Science and Technology, Kraków, Poland
Bo Zhang - Hunan University of Technology, China
Xiang Zhang - Wuhan University of Science and Technology, China
Eugeniusz Ziółkowski - AGH University of Science and Technology, Kraków, Poland
Sylwia Żymankowska-Kumon - AGH University of Science and Technology, Kraków, Poland
Andrzej Zyska - Czestochowa University of Technology, Poland



List of Reviewers 2020

Shailee Acharya - S. V. I. T Vasad, India
Mohammad Azadi - Semnan University, Iran
Rafał Babilas - Silesian University of Technology, Gliwice, Poland
Czesław Baron - Silesian University of Technology, Gliwice, Poland
Dariusz Bartocha - Silesian University of Technology, Gliwice, Poland
Emin Bayraktar - Supmeca/LISMMA-Paris, France
Jaroslav Beňo - VSB-Technical University of Ostrava, Czech Republic
Artur Bobrowski - AGH University of Science and Technology, Kraków, Poland
Grzegorz Boczkal - AGH University of Science and Technology, Kraków, Poland
Wojciech Borek - Silesian University of Technology, Gliwice, Poland
Pedro Brito - Pontifical Catholic University of Minas Gerais, Brazil
Marek Bruna - University of Žilina, Slovak Republic
John Campbell - University of Birmingham, United Kingdom
Ganesh Chate - Gogte Institute of Technology, India
L.Q. Chen - Northeastern University, China
Mirosław Cholewa - Silesian University of Technology, Gliwice, Poland
Khanh Dang - Hanoi University of Science and Technology, Viet Nam
Vladislav Deev - Wuhan Textile University, China
Brij Dhindaw - Indian Institute of Technology Bhubaneswar, India
Derya Dispinar - Istanbul Technical University, Turkey
Malwina Dojka - Silesian University of Technology, Gliwice, Poland
Rafał Dojka - ODLEWNIA RAFAMET Sp. z o. o., Kuźnia Raciborska, Poland
Anna Dolata - Silesian University of Technology, Gliwice, Poland
Agnieszka Dulska - Silesian University of Technology, Gliwice, Poland
Tomasz Dyl - Gdynia Maritime University, Poland
Maciej Dyzia - Silesian University of Technology, Gliwice, Poland
Eray Erzi - Istanbul University, Turkey
Katarzyna Gawdzińska - Maritime University of Szczecin, Poland
Sergii Gerasin - Pryazovskyi State Technical University, Ukraine
Dipak Ghosh - Forace Polymers Ltd, India
Marcin Górny - AGH University of Science and Technology, Kraków, Poland
Marcin Gołąbczak - Lodz University of Technology, Poland
Beata Grabowska - AGH University of Science and Technology, Kraków, Poland
Adam Grajcar - Silesian University of Technology, Gliwice, Poland
Grzegorz Gumienny - Technical University of Lodz, Poland
Libor Hlavac - VSB Ostrava, Czech Republic
Mariusz Holtzer - AGH University of Science and Technology, Kraków, Poland
Philippe Jacquet - ECAM, Lyon, France
Jarosław Jakubski - AGH University of Science and Technology, Kraków, Poland
Damian Janicki - Silesian University of Technology, Gliwice, Poland
Witold Janik - Silesian University of Technology, Gliwice, Poland
Robert Jasionowski - Maritime University of Szczecin, Poland
Jan Jezierski - Silesian University of Technology, Gliwice, Poland
Jadwiga Kamińska - Łukasiewicz Research Network – Krakow Institute of Technology, Poland
Justyna Kasinska - Kielce University Technology, Poland
Magdalena Kawalec - Akademia Górniczo-Hutnicza, Kraków, Poland
Angelika Kmita - AGH University of Science and Technology, Kraków, Poland
Ladislav Kolařík -Institute of Engineering Technology CTU in Prague, Czech Republic
Marcin Kondracki - Silesian University of Technology, Gliwice, Poland
Sergey Konovalov - Samara National Research University, Russia
Aleksandra Kozłowska - Silesian University of Technology, Gliwice, Poland
Janusz Krawczyk - AGH University of Science and Technology, Kraków, Poland
Halina Krawiec - AGH University of Science and Technology, Kraków, Poland
Ivana Kroupová - VSB - Technical University of Ostrava, Czech Republic
Agnieszka Kupiec-Sobczak - Cracow University of Technology, Poland
Tomasz Lipiński - University of Warmia and Mazury in Olsztyn, Poland
Aleksander Lisiecki - Silesian University of Technology, Gliwice, Poland
Krzysztof Lukaszkowicz - Silesian University of Technology, Gliwice, Poland
Mariusz Łucarz - AGH University of Science and Technology, Kraków, Poland
Katarzyna Major-Gabryś - AGH University of Science and Technology, Kraków, Poland
Pavlo Maruschak - Ternopil Ivan Pului National Technical University, Ukraine
Sanjay Mohan - Shri Mata Vaishno Devi University, India
Marek Mróz - Politechnika Rzeszowska, Rzeszów, Poland
Sebastian Mróz - Czestochowa University of Technology, Poland
Kostiantyn Mykhalenkov - National Academy of Science of Ukraine, Ukraine
Dawid Myszka - Politechnika Warszawska, Warszawa, Poland
Maciej Nadolski - Czestochowa University of Technology, Częstochowa, Poland
Konstantin Nikitin - Samara State Technical University, Russia
Daniel Pakuła - Silesian University of Technology, Gliwice, Poland


Ta strona wykorzystuje pliki 'cookies'. Więcej informacji