Applied sciences

Archives of Civil Engineering

Content

Archives of Civil Engineering | 2011 | No 2 |

Abstract

The article describes how to identify the boundary and yield surface for hypoplastic constitutive equations proposed by Wu, Gudehus and Bauer. It is shown how to identify and plot the surfaces for any equation in this class. Calculation errors are analyzed characteristic for applied set of numerical formulas. In the paper there are computer links to the source code prepared in the MATLAB system, based on instructions in the article. A sample consitutive domains are shown, plotted using the attached computer program.

Go to article

Abstract

Green-geo-engineering with geosynthetic reinforced soil structures is of increasing practice around the world. Poland is among the leading countries with the third biggest geogrid market in Europe. The German EBGEO 2010 Guideline for Soil Reinforcement with Geosynthetics as first European Guideline for Geosynthetics linked to the Eurocode 7, and the new design code for Japanese railway structures under seismic loading are introduced. New research results from the Geotechnical Institute of the RWTH Aachen, Germany, dealing with the soil/reinforcement interaction and new approaches for design codes for the reinforcement of base courses in traffic areas based on lab and field tests in the USA are presented.

Go to article

Abstract

The problem of consolidation of soil has been widely investigated. The basic approach was given by Terzaghi who assumed soil of constant physical and mechanical parameters. In the case of peat consolidation, the permeability coefficient of soil and the elasticity modulus are functions of the settlement which is an important additional factor. The model proposed here assumes varying the elasticity and permeability coefficients. Moreover, the settlement is described by the so-called elementary curve which was approximated empirically based upon laboratory tests. The model allows to consider the case when the filtration in the peat body goes in horizontal direction. It happens so when the charging layer does not receive outgoing water from the pores. The model includes also the case when the load involving consolidation varies in time i.e. the charging layer grows up gradually. The model has been applied practically in several cases and it comes that there is a good agreement between calculated and measured settlement of the consolidated peat layer.

Go to article

Abstract

A certain non-linear differential equation containing a power of unknown function being the solution is considered with application to selected geotechnical problems. The equation can be derived to a linear differential equation by a proper substitution and properties of operations G and S.

Go to article

Abstract

This paper presents simulation results of the consolidation process of the flotation waste landfill “Żelazny Most”. The mathematical model used in presented research is based on Biot’s model of consolidation and is extended with rheological skeleton. The load is the mass pressure of the landfill itself. The initial point selected for calculations was based on the ground water level calculated in a landfill. The creeping process in this waste landfill was analyzed along the north – south section. The solution is therefore 2D with the assumption of a plane strain state. Effective model parameters data were obtained in laboratory tests on the material from the waste landfill. Results obtained for a stress state in a storage state can help to determine whether the adopted linear model of visco-elastic medium does not lead to changes in the Coulomb – Mohr potential yield, showing the emergence of plasticity of material storage areas.

Go to article

Abstract

This paper compares numerical solutions of transient two-dimensional unsaturated flow equation by using different averaging schemes for internodal conductivities. Averaging methods such as arithmetic mean, geometric mean, upstream weighting, and integrated mean are taken into account, as well as a recent approach based on steady-state approximation. The latter method proved the most flexible, producing relatively accurate solutions for both downward and upward flow cases.

Go to article

Abstract

The paper deals with the properties and microstructure of Reactive Powder Concrete (RPC), which was developed at Cracow University of Technology. The influence of three different curing conditions: water (W), steam (S) and autoclave (A) and also steel fibres content on selected properties of RPC was analyzed. The composite characterized by w/s ratio equal to 0.20 and silica fume to cement ratio 20%, depending on curing conditions and fibres content, obtained compressive strength was in the range from 200 to 315 MPa, while modulus of elasticity determined during compression was about 50 GPa. During three-point bending test load-deflection curves were registered. Base on aforementioned measurements following parameters were calculated: flexural strength, stress at limit of proportionality (LOP), stress at modulus of rapture (MOR), work of fracture (WF), and toughness indices I₅, I₁₀ and I₂₀. Both amount of steel fibres and curing conditions influence the deflection of RPC during bending.

Go to article

Editorial office

Editor-in-Chief
Henryk Zobel


Deputy Editor-in-Chief
Mariola Książek


Scientific Advisory Committee
:
Andrzej M. Brandt
Werner Brilon (Germany)
Jacek Chróścielewski
Luc Courard (Belgium)
Andrzej Garbacz
Andrzej Garstecki
Wojciech Gilewski
Marian Giżejowski
Oleg Kapliński
Piotr Konderla
Aleksander Kozłowski
Marian Kwietniewski
Zbigniew Młynarek
Andrzej S. Nowak (USA)
Anna Siemińska-Lewandowska
Jan Szwabowski
Waldemar Świdziński
Andrew P. Tarko (USA)
Marian Tracz
Edmundas K. Zavadskas (Lithuania)
Jerzy Ziółko

Secretary
Katarzyna Orzeł

Contact

 

Politechnika Warszawska

Wydział Inżynierii Lądowej

Al. Armii Ludowej 16, 00-637 Warszawa, Polska Pokój 618; Telefon 22 234 62 84

e-mail: ace@il.pw.edu.pl;

website: http://ace.il.pw.edu.pl

 

 

 

Instructions for authors

GUIDELINES FOR AUTHORS

1. Preparation of the paper

General: Author is responsible for the Paper contents including copyrights and text formatting. The manuscript should be written in English. It should be typed using 12 p TNR font with 1.5 line spacing, on single-sided A4 sheets with 2 cm margins. The paper should not exceed 10 pages including tables and figures plus 2 pages of an extended summary (TNR 10 pt. justify align), started from new page at the end of the manuscript. Summary in Polish for Polish natives only, others - summary in English.

The first page and the main text: The first page of the article should contain: (1) the title of the article, (2) the name, academic merits, affiliation and e-mail of each author, (3) the name and the address of the author to whom correspondence, proofs and reprints should be sent, (4) a summary of 50-150 words, (5) a list of key words (not to exceed 8). The main text should be divided into numbered (1, 2, etc.) and titled sections and, if needed, into subsections (1.1, 1.2, ... in Section 1, 2.1, 2.2, ... in Section 2, etc.). The abstract of 50-150 words is required on a separate sheet. Polish natives authors only are requested to enclose Polish translation of the abstract, others - abstract in English.

Tables and figures: Tables and figures should be inserted into the text (black-and-white figures and glossy photographs),numbered consecutively and titled. They should be referred to in the text as Fig. 1, Fig. 2, ..., Table 1, Table 2. A list of figures and tables captions (TNR 11 pt. left align, in Polish - for Polish natives only and in English) should be provided on separate sheet(s) at the end of the manuscript beforean extended summary. Colour figures will be accepted only if the colour is essential for the explanation.

Units and mathematical formulae: SI units and abbreviations are obligatory. Mathematical formulae should be typewritten and centred. The formulae referred to in the text are to be numbered consecutively in each Section, i.e. (1.1), (1.2), ... in Section 1, (2.1), (2.2), ... in Section 2, etc. The numbers should be placed in parentheses ( ) at the left margin. The formulae are to be referred to in the text as Eq. (1.1),, Eq. (1.2), ..., Eq. (2.1), Eq. (2.2), ..., etc. The formulae not referred to in the text should not be numbered.

Bibliography: References are to be listed at the end of the paper in the alphabetical order and consecutively numbered. A reference to a published paper should be referred to in the text by the last name(s) of author(s) and the reference's number in brackets [ ]. Each item should contain full bibliographical data in the format illustrated by the following examples:

[1] M. Abramowitz and I. A. Stegun, Eds. Handbook of Mathematical Functions (Applied Mathematics Series 55). Washington, DC: NBS, 1964, pp. 32-33.

[2] M. Gorkii, “Optimal design”, Dokl. Akad. Nauk SSSR, vol. 12, pp. 111-122, 1961.

(Transl.: in L. Pontryagin, Ed., The Mathematical Theory of Optimal Processes. New York: INTERSCIENCE, 1962, Ch. 2, sec. 3, pp. 127-135).

[3] B. Klaus and P. Horn, Robot Vision. Cambridge, MA: MIT Press, 1986.

[4] E. F. Moore, “Gedanken-experiments on sequential machines”, in Automata Studies

(Ann. of Mathematical Studies, no. 1), C. E. Shannon and J. McCarthy, Eds. Princeton, NJ: Princeton Univ. Press, 1965, pp. 129-153.

[5] R. L. Myer, “Parametric oscillators and nonlinear materials”, in Nonlinear Optics, vol. 4, P. G. Harper and B. S. Wherret, Eds. San Francisco, CA: Academic, 1977, pp. 47-160.

[6] L. Stein, “Random patterns”, in Computers and You, J. S. Brake, Ed. New York: Wiley, 1994, pp. 55-70.

[7] Westinghouse Electric Corporation (Staff of Technology and Science, Aerospace Div.), Integrated Electronic Systems. Englewood Cliffs, NJ: Prentice-Hall, 1970.

[8] G. O. Young, “Synthetic structure of industrial plastics”, in Plastics, vol. 3, Polymers of Hexadromicon, J. Peters, Ed., 2nd ed. New York: McGraw-Hill, 1964, pp. 15-64.

In special cases, other formats related to codes, reports, dissertations, etc. will be accepted.

Layout of the text can be downloaded from ace website: http://ace.il.pw.edu.pl

2. Submission of the paper

Two electronic versions of the manuscript (DOC and PDF file) and License to publish should be submitted and sent directly to the Editor-in-chief by e-mail to: ace@il.pw.edu.pl

Signing license agreement is required.

3. Proof read: Proofs will be sent to the corresponding author to correct any typesetting errors. Alterations to the original manuscript at this stage will not be accepted. Corrected proofs page must be mailed to the Editorial Office as soon as possible.

4. Copyright: Submission of a paper to Archives of Civil Engineering implies that the material is an original and unpublished work, not under consideration for publication elsewhere. If permission for publication of any material is required, it should be obtained from appropriate sources by the author. The corresponding author is responsible for the other authors' approval of the paper publication.

5. Reprints: The corresponding author will receive ten reprints and PDF file of the published paper free of charge.

6. Other information: Apart from research papers, other articles such as review papers, brief notes, discussions and reports may be published in the journal. Monographic papers and state-of-the-art papers are accepted after prior approval of the Editor. Reports on important conferences held in Poland may also be published. Editor decides whether the paper fulfil all requirements i.e. formal and scientific. Editor nominates two reviewers, who shall forward reviews of the accepted publication.

The paper will be published in ACE provided that the reviews are positive. If reviewers have some comments authors have to correct the paper. Papers are subject to open discussion. All letters should be addressed to the Editorial Office and will be published together with the authors' response.

7. Fees: Submission of the paper is free of charge. Submitted papers are accepted for publication after a positive opinion of two independent reviewers. When publication accepted Author will be informed by email about article processing charge incl. amount and payment deadline. ACE is non for profit and all fees are calculated to cover operational costs only. Payment is required to the following bank account:

OFICYNA WYDAWNICZA POLITECHNIKI WARSZAWSKIEJ

ul. Polna 50, 00-644 WARSAW

PKO IV Department in WARSAW

Number: PL 84 1240 1053 1111 0000 0500 5707

with annotation: "Author(s) name and surname, ACE"

This page uses 'cookies'. Learn more