Nauki Techniczne

Archives of Foundry Engineering

Zawartość

Archives of Foundry Engineering | 2020 | vol. 20 | Ahead of print |

Abstrakt

This paper presents practical capabilities of a system for ceramic mould quality forecasting implemented in an industrial plant (foundry). The main assumption of the developed solution is the possibility of eliminating a faulty mould from a production line just before the casting operation. It allows relative savings to be achieved, and faulty moulds, and thus faulty castings occurrence in the production cycle to be minimized. The numerical computing module (the DEFFEM 3D package), based on the smoothed particle hydrodynamics (SPH) is one of key solutions of the system implemented. Due to very long computing times, the developed numerical module cannot be effectively used to carry out multi-variant simulations of mould filling and solidification of castings. To utilize the benefits from application of the CUDA architecture to improve the computing effectiveness, the most time consuming procedure of looking for neighbours was parallelized (cell-linked list method). The study is complemented by examples of results of performance tests and their analysis.

Przejdź do artykułu

Autorzy i Afiliacje

M. Hojny
K. Żaba
T. Dębiński
J. Porada

Abstrakt

The research paper presents the results of testing the strength and technological properties of molding sand with gypsum binder, the bonding process proceeded: naturally or conventionally. The tests included mass containing (parts by weight): 78 pbw. Grudzeń-Las quartz sand, 22 pbw. plaster gypsum "Dolina Nidy” and 9 pbw. water. Measurements of compressive strength, shear, tensile and bending as well as permeability and looseness were carried out on standard cylindrical samples kept in the air for 1 - 96 hours or dried at 110 oC for 1 - 8 hours. The results of the analysis were analyzed in connection with the mass structure and construction binding bridges warp grains observed with a scanning microscope (SEM). The influence of drying intensity on the bonding process and related mass properties has been demonstrated, especially from the point of view of the possibility of selection and / or intensification of a specific curing method for use in the production of gypsum binger molds and cores.

Przejdź do artykułu

Autorzy i Afiliacje

K. Granat
P. Paduchowicz
A. Dziedzic
M. Jamka
P. Biały

Abstrakt

APNB (alkaline phenolic no bake), widely known as Alphaset is one of the major sand binder systems used in foundries to make molds and cores without application of heat or gas. This is a two part system comprising of a phenol-formaldehyde resin in alkaline medium as binder and range of esters of dibasic acids and/or polyhydric alcohols as hardeners.

Resin performance varies depending upon formulations. Major variables in formulations are mole ratio of phenol: formaldehyde, total alkali content, ratio of two alkalis (NaOH & KOH) and molecular weight of polymers i.e. chain length.

In present work, one mole ratio of phenol & formaldehyde has been chosen to prepare 8 resins with following details.

Table 1.

Physical and chemical properties of eight (fresh) resins, A to H

Properties A B C D E F G H
Viscosity at 30°C (mPs-a) 56 47 66 51 39 44 49 52
Na (%) 5.94 3.21 5.94 3.21 nil 2.73 nil 2.73
K (%) nil 3.31 nil 3.31 7.18 3.87 7.18 3.87
Molecular weight Low Low High High Low Low High High
Gel Time at 121°C, mt-sec 27-0 29-30 24-0 30-0 30-0 27-30 26-30 26-0
Moisture (%) 52.43 52.42 53.01 53.75 55.58 54.12 51.61 54.03
Non-volatile Content (%) 48.74 47.25 49.10 49.35 47.63 47.32 48.06 48.29
Specific Gravity 1.182 1.177 1.183 1.180 1.172 1.184 1.178 1.188
Free Phenol (%) 0.47 0.42 0.44 0.43 0.37 0.27 0.41 0.20

Properties of these 8 formulations have been studied for strength and viscosity over a period of 12 weeks in 4 week interval.

Attempt has been made to develop a simple test for simulating hot & retained strength of molds in laboratory. Process followed for chasing hot and retained strength is described under clause 2.

With more and more understanding of the chemistry of alphaset system in last three & half decades it has been possible to identify role of variables contributing towards specific properties vis a vis developing tailor made formulations to fulfill requirements of individual foundries right from mold making to de coring.

Przejdź do artykułu

Autorzy i Afiliacje

D.K. Ghosh

Abstrakt

Surface phenomena play a major role in metallurgical processes; their operation results, among others, from the surface tension of liquid oxidic systems. One of the methods of determining surface tension of oxidic systems is performing calculations with Butler’s method. Surface tension was calculated for two- and three-component liquid oxidic systems typical of metallurgical processes. The determined dependence of surface tension in FeO-SiO2 at temp. 1773 K and CaO-SiO2 at temp.1873 K showed that with the growing participation of SiO2 surface tension decreased. Analogous calculations were performed for three-component systems: CaO-Al2O3-SiO2 and MnO-Al2O3- SiO2. The results of calculations of surface tension were determined for temp. 1873 K and compared with the results obtained by T. Tanaka et al. [19]. In both cases the increase of Al2O3 content resulted in a growth of surface tension. The simulation results were higher than experimental result, as compared to the literature data.

Przejdź do artykułu

Autorzy i Afiliacje

D. Kalisz

Abstrakt

The paper presents results of a study on the effect of passage of time on magnesium content in iron alloys and the effect of magnesium content on the number of vermicular graphite precipitations per unit surface area and value of the longitudinal ultrasonic wave velocity for two different vermicularization methods. The study was carried out with the use of inspection bar castings. For specific production conditions, it has been found that in case of application of both the cored wire injection method and the method of pouring liquid metal over magnesium master alloy on ladle bottom, the satisfactory level of magnesium content in the bottom-pour ladle, for which it was still possible to obtain castings with vermicular graphite, was 0.018% Mg. In case of the cored wire injection method, the “time window” available to a pouring station at which castings of vermicular cast iron are expected to be obtained, was about 5 minutes. This corresponds to the longitudinal ultrasonic wave velocity values exceeding 5500 m/s and the number of graphite precipitations per unit surface area above 320 mm–2. In case of the master alloy method, the respective “time window” allowing to obtain castings of vermicular cast iron was only about 3 minutes long. This corresponds to the longitudinal ultrasonic wave velocity value above 5400 m/s and the number of graphite precipitations per unit surface area above 380 mm–2.

Przejdź do artykułu

Autorzy i Afiliacje

M. Tupaj
A.W. Orłowicz
M. Mróz
B. Kupiec
D. Pająk
M. Kawiński

Abstrakt

This article is devoted to basalt reprocessing together with magnetite concentrate in order to obtain ferrous alloy and calcium carbide. The studies have been based on thermodynamic simulation and electric smelting in arc furnace. The thermodynamic simulation has been performed using HSC-5.1 software based on the principle of minimum Gibbs energy. The blend was smelted in arc furnaces. On the basis of the obtained results of combined processing of basalt, it has been established that under equilibrium conditions, the increase in carbon content from 36 to 42 wt % of basalt and concentrate mixture makes it possible to increase the aluminum extraction into the alloy up to 81.4%, calcium into calcium carbide – up to 51.4%, and silicon into the alloy – up to 78.5%. Increase in the amount of lime to 32% allows to increase the content of calcium carbide to 278 dm3/kg. Electric smelting of the blend under laboratory conditions in the presence of 17-32% of lime makes it possible to extract ferrous alloy containing 69.5-72.8% of silicon, 69.1-70.2% of aluminum, and to obtain ferrous alloy containing 49-53% of ΣSi and Al and calcium carbide in the amount of 233-278 dm3/kg. During large-scale laboratory smelting of blend comprised of basalt (38.5%), magnetite concentrate (13.4%), lime (15.4%), and coke fines (32.7%), the ferrous alloy has been produced containing 48-53% of ΣSi and Al, calcium carbide in amount of 240-260 dm3/kg. Extraction of Si and Al into the alloy was 70.4 and 68.6%, respectively; Ca into carbide – 60.3%; Zn and Pb into sublimates – 99.6 and 92.8%, respectively.

Przejdź do artykułu

Autorzy i Afiliacje

V.M. Shevko
G.E. Karataeva
A.D. Badikova
M.A. Tuleev
R.A. Uteeva

Abstrakt

The paper presents the properties of plastics under the trade names of PMMA and Midas, and of Formowax, Romocast 305 and Romocast 930 casting waxes. Their effect on the quality of foundry patterns used in the manufacture of ceramic moulds for precision casting is also discussed. From the selected materials for foundry patterns, samples were made for testing using the following methods: (i) 3D printing in the case of plastics, and (ii) conventional method based on tooling in the form of metal moulds (dies) in the case of casting waxes.

The most important physico-mechanical properties of materials for foundry patterns were determined, i.e. linear shrinkage, softening temperature, relative elongation and coefficient of thermal linear expansion. Bending tests were carried out on samples of patterns printed and made in metal moulds, including determination of the surface roughness of patterns.

After the process of melting out patterns from the cavities of ceramic moulds in an autoclave, the degree of their melting out was visually assessed (i.e. the residues from pattern removal were evaluated). The ash content after burning out of foundry patterns was also determined. The conducted tests allowed comparing the important parameters of materials used for foundry patterns and assessing the suitability of selected plastics as a material for foundry patterns used in the manufacture of high-quality precision castings.

Przejdź do artykułu

Autorzy i Afiliacje

A. Dydak
M. Książek

Abstrakt

Recyclability is one of the great features of aluminium and its alloys. However, it has been typically considered that the secondary aluminium quality is low and bad. This is only because aluminium is so sensitive to turbulence. Uncontrolled transfer and handling of the liquid aluminium results in formation of double oxide defects known as bifilms. Bifilms are detrimental defects. They form porosity and deteriorate the properties. The detection and quantification of bifilms in liquid aluminium can be carried out by bifilm index measured in millimetres as an indication of melt cleanliness using Reduced Pressure Test (RPT). In this work, recycling efficiency and quality change of A356 alloy with various Ti additions have been investigated. The charge was recycled three times and change in bifilm index and bifilm number was evaluated. It was found that when high amount of Ti grain refiner was added, the melt quality was increased due to sedimentation of bifilms with Ti. When low amount of Ti is added, the melt quality was degraded.

Przejdź do artykułu

Autorzy i Afiliacje

O. Gursoy
E. Erzi
K. Tur
D. Dispinar

Abstrakt

This article is a description of the progress of research and development in the area of massive large-scale castings - slag ladles implemented in cooperation with the Faculty of Foundry Engineering of UST in Krakow. Slag ladles are the one of the major castings that has been developed by the Krakodlew (massive castings foundry) for many years. Quality requirements are constantly increasing in relation to the slag ladles. Slag ladles are an integral tool in the logistics of enterprises in the metallurgical industry in the process of well-organized slag management and other by-products and input materials. The need to increase the volume of slag ladles is still growing. Metallurgical production is expected to be achieved in Poland by 2022 at the level of 9.4 million Mg/year for the baseline scenario - 2016 - 9 million Mg/year. This article describes the research work carried out to date in the field of technology for the production of massive slag ladles of ductile cast iron and cast steel.

Przejdź do artykułu

Autorzy i Afiliacje

M. Paszkiewicz
E. Guzik
D. Kopyciński
B. Kalandyk
A. Burbelko
D. Gurgul
S. Sobula
A. Ziółko
K. Piotrowski
P. Bednarczyk

Abstrakt

The paper presents an example of the application of vibratory machining for castings based on the results of visual testing. The purpose of the work is to popularize non-destructive testing and vibratory machining as finishing process, especially in the case of cast objects. Visual testing is one of the obligatory non-destructive tests used for castings and welded joints. The basic requirements concerning the dimensional accuracy and surface texture of cast components are not met if visible surface flaws are detected. The tested castings, which had characteristic traces of the casting process, were subjected to vibratory machining. The machining with loose abrasive media in vibrating containers is aimed at smoothing the surface and reducing or completely removing flashes. To complement the visual testing were also conducted research on the contact profilometer Taylor Hobson PGI 1200. Particular attention was focused on measuring the height of flashes and changes in the surface of smoothed details based on BNIF No. 359 touch-visual patterns. Based on the work, it can be concluded that vibratory machining allows for removal flashes and smoothing of the surface of aluminum alloy cast objects.

Przejdź do artykułu

Autorzy i Afiliacje

D. Bańkowski
P. Młynarczyk

Redakcja

CHIEF EDITORS
Editor
J. Szajnar
Deputy Editor
J. Jezierski

SUBJECT EDITORS
Theoretical Aspects of Casting Processes
K. Eigenfeld – Freiberg, Germany
E. Guzik – Kraków, Poland
T. G. Mathia - Lyon, France
W. Wołczyński – Kraków, Poland
Innovative Foundry Technologies and Materials
T. Elbel – Ostrava, Czech Republic
Z. Ignaszak – Poznań, Poland
O. P. Pandey – Punjab, India
A. Pereira - Vigo, Spain
Foundry Processes Computer Aiding
B. Mochnacki – Częstochowa, Poland
J. Roučka – Brno, Czech Republic
J.S. Suchy – Kraków, Poland
Mechanization, Automation and Robotics in Foundry
J. Bast – Freiberg, Germany
R. Wrona – Kraków, Poland
Transport Systems in Foundry
J. Dańko – Kraków, Poland
Z. Li – Shijiazhuang, China
Castings Quality Management
D. Bolibruchova– Żilina, Slovak Republic
J. D. B. de Mello - Santa Monica, Brazil
M. Perzyk – Warszawa, Poland
Environment Protection
M. Holtzer – Kraków, Poland
H. Polzin – Freiberg, Germany
J. Sobczak – Kraków, Poland
I. Volchok – Zaporizhzhya, Ukraine

EDITORIAL ADVISORY BOARD
J. Braszczyński – Częstochowa, Poland
B. K. Dhindaw – Rupnagar, India
L. A. Dobrzański – Gliwice, Poland
W. A. Hufenbach – Dresden, Germany
P. Jelínek – Ostrava, Czech Republic
L. Jeziorski – Częstochowa, Poland
J. Lacaze – Toulouse, France
V. L. Naydek – Kiev, Ukraine
A. Passerone – Genova, Italy
I. Riposan – Bucharest, Romania
F. Romankiewicz – Zielona Góra, Poland
A. Sládek – Żilina, Slovak Republic

INTERNATIONAL SCIENTIFIC REVIEW COMMITTEE
S. A. Argyropoulos – Toronto, Canada
M. Azadi – Tehran, Iran
Y. Babaskin – Kiev, Ukraine
K. Bako – Miskolc, Hungary
E. Bayraktar – Paris, France
L. Bechný – Zilina, Slovak Republic
V. Bednarova - Ostrava, Czech Republic
F. Bińczyk – Katowice, Poland
A. Bokota – Częstochowa, Poland
G.P. Borisov – Kiev, Ukraine
A. Bydałek – Kraków, Poland
C. H. Cáceres – Brisbane, Australia
J. Čech – Brno, Czech Republic
L. Q. Chen – Shenyang, China
A. Chojecki – Kraków, Poland
M. Cholewa – Gliwice, Poland
I. A. Dibrov – Moscow, Russia
D. Dispinar – Istanbul, Turkey
S. M. Dobosz – Kraków, Poland
V. I. Dubodelov – Kiev, Ukraine
A. Fedoryszyn – Krakow, Poland
J. Głownia – Kraków, Poland
K. Granat – Wrocław, Poland
J. Hampl – Ostrava, Czech Republic
J. Helber – Düsseldorf, Germany
M. Hetmańczyk – Katowice, Poland
M. Horáček – Brno, Czech Republic
M. Kaczorowski – Warszawa, Poland
W. Kapturkiewicz – Kraków, Poland
R. Kawalla – Freiberg, Germany
Z. Konopka – Czestochowa, Poland
D. Kopyciński – Kraków, Poland
W. K. Krajewski – Kraków, Poland
Z. Libo – Beijing, China
P. Lichy – Ostrava, Czech Republic
Y. P. Lim – Setapak, Malaysia
T. Lipiński – Olsztyn, Poland
E. Majchrzak – Gliwice, Poland
A. Mityayev - Zaporizhzhya, Ukraine
M. Murgaš – Trnava, Slovak Republic
I. Nová – Liberec, Czech Republic
W. Orłowicz – Rzeszów, Poland
T. Pacyniak – Łódź, Poland
B. Piekarski – Szczecin, Poland
A. Rimmer – West Bromwich, United Kingdom
S. Samavedam – Hyderabad, India
P. Schumacher – Leoben, Austria
N. Sczygiol – Częstochowa, Poland
P. Skočovský – Żilina, Slovak Republic
M.S. Soiński – Częstochowa, Poland
J. Sokolowski – Ottawa, Kanada
K. V. Sudhakar – Butte, USA
B. G. Thomas - Champaign, USA
M. Trbižan – Ljubljana, Slovenia
J. Vuorinen – Tampere, Finland
E. Ziółkowski – Kraków, Poland
J. Zych – Kraków, Poland

ASSOCIATE EDITORS
D. Bartocha – Gliwice, Poland, - editorial secretary
J. Suchoń – Gliwice, Poland - editorial secretary
J. Szymszal – Katowice, Poland, Statistic Editor
A. Dulska – Gliwice, Poland
M. Kondracki – Gliwice, Poland
C. Borek –Chicago, USA, Language Editor

 

Kontakt

ul. Towarowa 7,
44-100 Gliwice, Poland
e-mail: kikm@polsl.pl

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji