Nauki Techniczne

Archive of Mechanical Engineering

Zawartość

Archive of Mechanical Engineering | 2014 | vol. 61 | No 3 |

Abstrakt

With widespread use of pesticides in modern agriculture, the impacts of spray drift have become a topic of considerable interest. The drifting of sprays is a highly complex process influenced by many factors. The paper presents results of experimental research on a drifting cloud of droplets dispersing from aircraft. Experiments were conducted to quantify spray drift from aerial applications of pesticide. Parallel to the blowing wind, the measurement line 800 m long was disposed. The relationships between the relative dose and the distance of drift as well as spray density and its structure on the measuring length have been established.

Przejdź do artykułu

Autorzy i Afiliacje

Tomasz Seredyn
Robert Rowiński

Abstrakt

In this paper, by using a semi-analytical solution based on multi-layered approach, the authors present the solutions of temperature, displacements, and transient thermal stresses in functionally graded circular hollow cylinders subjected to transient thermal boundary conditions. The cylinder has finite length and is subjected to axisymmetric thermal loads. It is assumed that the functionally graded circular hollow cylinder is composed of N fictitious layers and the properties of each layer are assumed to be homogeneous and isotropic. Time variations of the temperature, displacements, and stresses are obtained by employing series solving method for ordinary differential equation, Laplace transform techniques and a numerical Laplace inversion.

Przejdź do artykułu

Autorzy i Afiliacje

Jafar Eskandari Jam
Y. Rahmati Nezhad

Abstrakt

Limb physical movements disability is the result of illnesses or serious injuries, impaired execution of daily activities and limitations or even inability to perform working activity. Restoration of fitness in such cases is possible through rehabilitation that requires arduous repetition of appropriate exercises with participation of an experienced physiotherapist. Exercises using the robot to repeat movements would speed up the process of rehabilitation. The paper presents the concept of rehabilitation robot control system realizing a specified purpose.

Przejdź do artykułu

Autorzy i Afiliacje

Andrzej Michnik
Jacek Brandt
Zbyszek Szczurek
Michał Bachorz
Zbigniew Paszenda
Robert Michnik
Jacek Jurkojć
Wiesław Rycerski
Jan Janota

Abstrakt

The paper presents the results of measurements and predictions of radial thrust in centrifugal pump with specific speed ns = 26. In the pump tested, a volute with rectangular cross-section was used. The tests were carried out for several rotational speeds, including speeds above and below the nominal one. Commercial code ANSYS Fluent was used for the calculations. Apart from the predictions of the radial force, the calculations of axial thrust were also conducted, and correlation between thrust and the radial force was found. In the range of the measured rotational speeds, similarity of radial forces was checked.

Przejdź do artykułu

Autorzy i Afiliacje

Krzysztof Karaskiewicz
Marek Szlaga

Abstrakt

Friction stir welding is a solid state innovative joining technique, widely being used for joining aluminium alloys in aerospace, marine automotive and many other applications of commercial importance. The welding parameters and tool pin profile play a major role in deciding the weld quality. In this paper, an attempt has been made to understand the influences of welding speed and pin profile of the tool on friction stir welded joints of AA6082-T6 alloy. Three different tool pin profiles (tapered cylindrical four flutes, triangular and hexagonal) have been used to fabricate the joints at different welding speeds in the range of 30 to 74 mm/min. Microhardness (HV) and tensile tests performed at room temperature were used to evaluate the mechanical properties of the joints. In order to analyse the microstructural evolution of the material, the weld’s cross-sections were observed optically and SEM observations were made of the fracture surfaces. From this investigation it is found that the hexagonal tool pin profile produces mechanically sound and metallurgically defect free welds compared to other tool pin profiles.

Przejdź do artykułu

Autorzy i Afiliacje

Hiralal Subhash Patil
Sanjay N. Soman

Abstrakt

On the basis of Euler-Bernoulli beam theory, the large-amplitude free vibration analysis of functionally graded beams is investigated by means of a finite element formulation. The von Karman type nonlinear strain-displacement relationship is employed where the ends of the beam are constrained to move axially. The material properties are assumed to be graded in the thickness direction according to the power-law and sigmoid distributions. The finite element method is employed to discretize the nonlinear governing equations, which are then solved by the direct numerical integration technique in order to obtain the nonlinear vibration frequencies of functionally graded beams with different boundary conditions. The influences of power-law index, vibration amplitude, beam geometrical parameters and end supports on the free vibration frequencies are studied. The present numerical results compare very well with the results available from the literature where possible.

Przejdź do artykułu

Autorzy i Afiliacje

Mehdi Javid
Milad Hemmatnezhad

Abstrakt

Considering the developing role of the friction stir welding in manufacturing industry, a complete study on the process is necessary. Studies on each stage of the process in particular, provide a better understanding of friction stir welding, and specially friction stir spot welding. In this study, plunge stage has been studied by experimental methods for investigating the temperature distribution around the tool during the plunge stage and microstructure changes of the workpiece. Experiments were performed on aluminium 7050 plates with coincident measurement of temperature. In the study, the tool which has a triangle pin is used. The results of this study are used as initial conditions for theoretical analysis of welding process. The results show that the temperature distribution around the tool is quite asymmetric. The asymmetric distribution of temperature is due to nonuniform load distribution underneath the tool and tilt angle of it. The temperatures of the points behind the tool are higher compared with points located forward the tool. Microstructural studies showed that four regions with different microstructures are formed around the tool during the process. These areas were separated based on differences in grain size and elongations. Grains near the tool are elongated in a particular direction that show the material flow direction.

Przejdź do artykułu

Autorzy i Afiliacje

Hossain Bisadi
Sajad Rasaee
Mohammad Farahmand

Abstrakt

In this article, the thick truncated cone shell is divided into disk-layers form with their thickness corresponding to the thickness of the cone. Due to the existence of shear stress in the truncated cone, the equations governing disk layers are obtained based on first shear deformation theory. These equations are in the form of a set of general differential equations. Given that the truncated cone is divided into n disks, n sets of differential equations are obtained. The solution of this set of equations, applying the boundary conditions and continuity conditions between the layers, yields displacements and stresses. The results obtained have been compared with those obtained through the analytical solution and the numerical solution. For the purpose of the analytical solution, use has been made of matched asymptotic method (MAM) and for the numerical solution, the finite element method (FEM).

Przejdź do artykułu

Autorzy i Afiliacje

Mohammad Zamani Nejad
Mehdi Jabbari
Mehdi Ghannad

Redakcja

Editor-in-Chief

Prof. Marek Wojtyra, Warsaw University of Technology, Poland

 

Editorial Board

Prof. Krzysztof Arczewski, Warsaw University of Technology, Poland

Prof. Janusz T. Cieśliński, Gdańsk University of Technology, Poland

Prof. Antonio Delgado, LSTM University of Erlangen-Nuremberg, Germany

Prof. Peter Eberhard, University of Stuttgart, Germany

Prof. Jerzy Maciej Floryan, The University of Western Ontario, Canada

Prof. Janusz Frączek, Warsaw University of Technology, Poland

Prof. Zbigniew Kowalewski, Institute of Fundamental Technological Research, Polish Academy of Sciences, Poland

Prof. Zenon Mróz, Institute of Fundamental Technological Research, Polish Academy of Sciences, Poland

Prof. Andrzej J. Nowak, Silesian University of Technology, Poland

Dr. Andrzej F. Nowakowski, The University of Sheffield, United Kingdom

Prof. Jerzy Sąsiadek, Carleton University, Canada

Prof. Jacek Szumbarski, Warsaw University of Technology, Poland

Prof. Tomasz Wiśniewski, Warsaw University of Technology, Poland

Prof. Günter Wozniak, Chemnitz University of Technology, Germany

 

Assistant to the Editor

Małgorzata Broszkiewicz, Warsaw University of Technology, Poland

 

Editorial Advisory Board

Prof. Alberto Carpinteri, Politecnico di Torino, Italy

Prof. Fernand Ellyin, University of Alberta, Canada

Prof. Feng Gao, Shanghai Jiao Tong University, P.R. China

Prof. Emmanuel E. Gdoutos, Democritus University of Thrace, Greece

Prof. Gregory Glinka, University of Waterloo, Ontario, Canada

Prof. Andrius Marcinkevicius, Vilnius Gedeminas Technical University, Lithuania

Prof. Manuel José Moreira De Freitas, Instituto Superior Tecnico, Portugal

Prof. Andrzej Neimitz, Kielce University of Technology, Poland

Prof. Thierry Palin-Luc, Arts et Métiers ParisTech, Institut Carnot Arts, France

Prof. Andre Pineau, Centre des Matériaux, Ecole des Mines de Paris, France

Prof. Narayanaswami Ranganathan, LMR, Ecole Polytechnique de l'Université de Tours, France

Prof. Jan Ryś, Cracow University of Technology, Poland

Prof. Adelia Sequeira, Technical University of Lisbon, Portugal,

Prof. Józef Szala, University of Technology and Life Sciences in Bydgoszcz, Poland

Prof. Edmund Wittbrodt, Gdańsk University of Technology, Poland

Prof. Jens Wittenburg, Karlsruhe Institute of Technology, Germany

Prof. Stanisław Wojciech, University of Bielsko-Biała, Poland

 

Language Editor

Lech Śliwa, Institute of Physiology and Pathology of Hearing, Warsaw, Poland

  

Kontakt

ARCHIVE OF MECHANICAL ENGINEERING

Editorial Office:

Institute of Aeronautics and Applied Mechanics, Warsaw University of Technology

Nowowiejska 24, Room 132, 00-665 Warsaw, Poland

Phone:  (+48) 22 234 7448, fax: (+48) 22 628 25 87,

E-mail: ame.eo@meil.pw.edu.pl

https://www.editorialsystem.com/ame

www.journals.pan.pl/ame

Instrukcje dla autorów

About the Journal
Archive of Mechanical Engineering is an international journal publishing works of wide significance, originality and relevance in most branches of mechanical engineering. The journal is peer-reviewed and is published both in electronic and printed form. Archive of Mechanical Engineering publishes original papers which have not been previously published in other journal, and are not being prepared for publication elsewhere. The publisher will not be held legally responsible should there be any claims for compensation. The journal accepts papers in English.

Archive of Mechanical Engineering is an Open Access journal. The journal does not have article processing charges (APCs) nor article submission charges.

Original high quality papers on the following topics are preferred:

  • Mechanics of Solids and Structures,
  • Fluid Dynamics,
  • Thermodynamics, Heat Transfer and Combustion,
  • Machine Design,
  • Computational Methods in Mechanical Engineering,
  • Robotics, Automation and Control,
  • Mechatronics and Micro-mechanical Systems,
  • Aeronautics and Aerospace Engineering,
  • Heat and Power Engineering.

All submissions to the AME should be made electronically via Editorial System - an online submission and peer review system at: https://www.editorialsystem.com/ame

More detailed instructions for Authors can be found there.

Polityka Open Access

Archive of Mechanical Engineering jest czasopismem wydawanym w wolnym dostępie na licencji CC BY-NC-ND 4.0. https://creativecommons.org/licenses/by-nc-nd/4.0/

Archive of Mechanical Engineering is an open access journal with all content available with no charge in full text version. The journal content is available under the licencse CC BY-NC-ND 4.0 https://creativecommons.org/licenses/by-nc-nd/4.0/.

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji