Applied sciences

Archives of Acoustics

Content

Archives of Acoustics | 2010 | vol. 35 | No 4

Download PDF Download RIS Download Bibtex

Abstract

In this paper, a new lifting wavelet domain audio watermarking algorithm based on the statistical characteristics of sub-band coefficients is proposed. First of all, an original audio signal was segmented and each segment was divided into two sections. Then, the Barker code was used for synchronization, the LWT (lifting wavelet transform) was performed on each section, a synchronization code and a watermark were embedded into the first section and the second section, respectively, by modifying the statistical average value of the sub-band coefficients. The embed strength was determined adaptively according to the auditory masking property. Experiments show that the embedded watermark has better robustness against common signal processing attacks than present algorithms based on LWT and can resist random cropping in particular.

Go to article

Authors and Affiliations

Zhi Tao
He-ming Zhao
Jun Wu
Ji-hua Gu
Yi-shen Xu
Di Wu
Download PDF Download RIS Download Bibtex

Abstract

Acoustical attenuation spectra in the frequency range 12 kHz - 2 GHz and nonequilibrium time domain measurements are briefly reviewed for aqueous solutions of various mono- and disaccharides as well as alkyl glycosides. Several relaxation regimes emerge with relaxation times between 10-11 s and 103 s. In this paper relaxation terms reflecting conformational changes are discussed, particularly mutarotation (103 s), chair-chair ring inversion (1 μs), two modes of pseudorotation (100 ns, 10 ns), disaccharide ring isomerisation (10 ns), and exocyclic side group rotation (1 ns).

Go to article

Authors and Affiliations

Udo Kaatze
Download PDF Download RIS Download Bibtex

Abstract

Results from broadband acoustical spectroscopy for aqueous solutions of mono- and disaccharides with salts added, of various alkyl glycosides, and of α-cyclodextrin with n-octyl-β-D-glucopyranoside added are briefly summarized in view of their relevance in the study of molecular association and complexation processes. Mono- and tridentate complexes of alkali earth ions with saccharides are discussed as well as the monomer exchange between micellar structures and the suspending phase in the alkyl glycoside surfactant solutions. Particular attention is given to the behaviour at solute concentrations close to the critical micelle concentration or aggregate concentration, respectively. Also described is the competition between inclusion complex formation and self-aggregation in solutions containing cyclodextrin and alkyl glycoside surfactant.

Go to article

Authors and Affiliations

Udo Kaatze
Download PDF Download RIS Download Bibtex

Abstract

This paper proposes an improved method of solving the permutation problem inherent in frequency-domain of convolutive blind source separation (BSS). It combines a novel inter-frequency dependence measure: the power ratio of separated signals, and a simple but effective bin-wise permutation alignment scheme. The proposed method is easy to implement and surpasses the conventional ones. Simulations have shown that it can provide an almost ideal solution of the permutation problem for a case where two or three sources were mixed in a room with a reverberation time of 130 ms.

Go to article

Authors and Affiliations

Lin Wang
Heping Ding
Fuliang Yin
Download PDF Download RIS Download Bibtex

Abstract

The use of therapeutic ultrasound continues to grow. A focused ultrasonic wave can increase the tissue temperature locally for the non-invasive cancer treatment or other medical applications. The authors have designed a seven-element annular array transducer operating at 2.4 MHz. Each element was excited by sine burst supplied by a linear amplifier and FPGA control circuits. The acoustic field, generated by a transducer was initially numerically simulated in a computer and next compared to water tank hydrophone measurements performed at 20, 40 and 60 mm focal depth. The results showed good agreement of the measurements with theory and the possibility to focus the ultrasound in the preselected area. The total acoustic power radiated by the annular array was equal to 2.4 W.

Go to article

Authors and Affiliations

Wojciech Secomski
Marcin Lewandowski
Andrzej Nowicki
Janusz Wójcik
Mateusz Walczak
Ryszard Tymkiewicz
Download PDF Download RIS Download Bibtex

Abstract

The assessment of teachers' exposure to noise in primary schools was carried out on the basis of: questionnaire studies (covering 187 teachers in 3 schools), noise measurements at the teachers' workplaces, measurements of the school rooms acoustic properties (reverberation time and speech transmission index STI in 72 classrooms), analysis of statistical data regarding hazards and occupational diseases in the education sector. The studies have shown that noise is the main factor of annoyance in the school environment. Over 50% of questioned teachers consider noise as annoying and near 40% as very annoying or unbearable. A-weighted equivalent continuous sound pressure levels measured in classrooms, teacher rooms and common rooms are in the range of 58-80 dB and they exceed 55 dB (criteria of noise annoyance). The most frequently reported subjective feelings and complaints (over 90%) are: growth of psychical and emotional tension, irritation, difficulties in concentrating, hoarseness, cough. Noise in schools is also a harmful factor. High A-weighted equivalent continuous sound pressure levels ranging from 80 to 85 dB, measured in corridors during pauses and in sports halls, can cause the risk of hearing damage among PE teachers and persons oversensitive to noise. The latter concerns both teachers and pupils. High background noise levels (55-65 dB) force teachers to raise their voice. It can lead to the development of an occupational disease - chronic voice disorders due to excessive vocal effort lasting for at least 15 years. In the education sector 785 new cases of this disease were reported only in 2008. Poor acoustics in classrooms (reverberation time ranging from 0.8 to 1.7 s, STI < 0.6 in 50% of classrooms) have an adverse influence on speech reception and make the teaching and learning processes difficult.

Go to article

Authors and Affiliations

Danuta Augustyńska
Anna Kaczmarska
Witold Mikulski
Jan Radosz
Download PDF Download RIS Download Bibtex

Abstract

This paper proposes a new approach for calculating the impulse response of room acoustics. Impulse response provides unique characterization of any discrete lineartime invariant (LTI) systems. We assume that the room is a linear time-invariant system and the impulse response is calculated simply by sending a Dirac Impulse into the system as input and getting the response from the output. Then, the output of the system is represented as a sum of time-shifted weighted impulse responses. Both mathematical justifications for the proposed method and results from simulation software developed to evaluate the proposed approach are presented in detail.

Go to article

Authors and Affiliations

Adil Alpkocak
Malik Sis
Download PDF Download RIS Download Bibtex

Abstract

Ultrasonic methods of human body internal structures imaging are being continuously enhanced. New algorithms are created to improve certain output parameters. A synthetic aperture method (SA) is an example which allows to display images at higher frame-rate than in case of conventional beam-forming method.

Higher computational complexity is a limitation of SA method and it can prevent from obtaining a desired reconstruction time. This problem can be solved by neglecting a part of data. Obviously it implies a decrease of imaging quality, however a proper data reduction technique would minimize the image degradation.

A proposed way of data reduction can be used with synthetic transmit aperture method (STA) and it bases on an assumption that a signal obtained from any pair of transducers is the same, no matter which transducer transmits and which receives. According to this postulate, nearly a half of the data can be ignored without image quality decrease.

The presented results of simulations and measurements with use of wire and tissue phantom prove that the proposed data reduction technique reduces the amount of data to be processed by half, while maintaining resolution and allowing only a small decrease of SNR and contrast of resulting images.

Go to article

Authors and Affiliations

Piotr Karwat
Marcin Lewandowski
Ziemowit Klimonda
Andrzej Nowicki
Michał Sęklewski
Download PDF Download RIS Download Bibtex

Abstract

Assessment of several noise indicators are determined by the logarithmic mean <img src="/fulltext-image.asp?format=htmlnonpaginated&src=P42524002G141TV8_html\05_paper.gif" alt=""/>, from the sum of independent random results L1; L2; : : : ; Ln of the sound level, being under testing. The estimation of uncertainty of such averaging requires knowledge of probability distribution of the function form of their calculations. The developed solution, leading to the recurrent determination of the probability distribution function for the estimation of the mean value of noise levels and its variance, is shown in this paper.

Go to article

Authors and Affiliations

Wojciech Batko
Bartosz Przysucha
Download PDF Download RIS Download Bibtex

Abstract

A trabecular bone consists of trabeculae whose mechanical properties differ significantly from the surrounding marrow, therefore an ultrasonic wave propagating within the bone structure is strongly scattered. The aim of this paper was to evaluate the contribution of the first, second and higher order scattering (multiple scattering) into the total scattering of ultrasound in a trabecular bone. The scattering due to the interconnections between thick trabeculae, usually neglected in trabecular bone models, has been also studied. The basic element in our model of the trabecular bone was an elastic cylinder with a various finite-length and diameter as well as orientation. The applied model was taking into account variation of both, elements size and their spatial configuration. The field scattered on the bone model was evaluated by solving numerically the integral form of the generalized Sturm-Liouville equation describing a scalar wave in inhomogeneous and lossy media. For the scattered fields calculated numerically the effective cross-sections were determined. The influence of absorption on the scattering coefficients was demonstrated. The results allowed to conclude that within the frequency range from 0.5 to 1.5 MHz contribution of the second order scattering to the effective backscattering cross-section is at least 500 times lower than that due to the first order scattering. It was noticed that for a frequency higher than 1.5 MHz fast growth of the backscattering (reflection) coefficients, calculated for the second order scattering, occurs.

Go to article

Authors and Affiliations

Andrzej Nowicki
Janusz Wójcik
Jerzy Litniewski
Download PDF Download RIS Download Bibtex

Abstract

Mixed boundary-value problem for periodic baffles in acoustic medium is solved with help of the method developed earlier in electrostatics. The nice feature of the method is that the resulting matrices are relatively easy for computations and that the results satisfy exactly the energy conservation law. Illustrative numerical examples present the wave-beam steering (in the far-field) in a baffle system that may be considered as a model of one-dimensional ultrasonic transducer array.

Go to article

Authors and Affiliations

Yuriy Tasinkevych
Eugeniusz Danicki
Download PDF Download RIS Download Bibtex

Abstract

Pure-tone audiometry (PTA) and transient-evoked otoacoustic emissions (TEOAEs) were determined in 57 classical orchestral musicians along with a questionnaire inquiry using a modified Amsterdam Inventory for Auditory Disability and Handicap ((m)AIADH). Data on musicians' working experience and sound pressure levels produced by various groups of instruments were also collected. Measured hearing threshold levels (HTLs) were compared with the theoretical predictions calculated according to ISO 1999:1990. High frequency notched audiograms typical for noise-induced hearing loss were found in 28% of the subjects. PTA and TEOAE consistently showed a tendency toward better hearing in females vs. males, younger vs. older subjects, and lower- vs. higher-exposed to orchestral noise subjects. Audiometric HTLs were better than theoretical predictions in the frequency range of 2000-4000 Hz. The (m)AIADH scores indicated some hearing difficulties in relation to intelligibility in noisy environment in 26% of the players. Our results indicated a need to implement a hearing conservation program for this professional group.

Go to article

Authors and Affiliations

Małgorzata Pawlaczyk-Łuszczyńska
Adam Dudarewicz
Małgorzata Zamojska
Mariola Śliwińska-Kowalska
Download PDF Download RIS Download Bibtex

Abstract

The results of long-term continuous noise measurements in two selected schools are presented in the paper. Noise characteristics were measured continuously there for approximately 16 months. Measurements started eight months prior to the acoustic treatment of the school corridors of both schools. An evaluation of the acoustic climates in both schools, before and after the acoustic treatment, was performed based on comparison of these two periods of continuous measurements. The autonomous noise monitoring stations, engineered at the Multimedia Systems Department of the Gdańsk University of Technology were used for this purpose. Investigations of measured noise, especially its influence on hearing sense, assessed on ground of spectral analyses in critical bands, is discussed. Effects of occupational noise exposure, including the Temporary Threshold Shift simulation, are determined. The correlation of the above said measurement results with respective instantaneous noise levels is discussed, and concluding remarks are presented. Some additional indicators such as air pollution or video analysis aiming at the analysis of corridor occupancy are also measured. It should be remembered that excessive noise, or air pollution may be evidence of a dangerous event and may pose health risks.

Go to article

Authors and Affiliations

Józef Kotus
Andrzej Czyżewski
Bożena Kostek
Maciej Szczodrak
Download PDF Download RIS Download Bibtex

Abstract

Synthetic aperture (SA) technique is a novel approach to present day commercial systems and has previously not been used in medical ultrasound imaging. The basic idea of SA is to combine information acquired simultaneously from all directions over a number of emissions and to reconstruct the full image from these data.

The paper presents the multi-element STA (MSTA) method for medical ultrasound imaging. The main difference with the STA approach is the use of a few elements in the transmit mode in contrast to a single element aperture. This allows increasing the system frame rate, decreasing the number of emissions, and provides the best compromise between the penetration depth and lateral resolution. Besides, a modified MSTA is proposed with a corresponding RF signal correction in the receive mode, which accounts for the element directivity property.

In the experiments a 32-element linear transducer array with 0.48 mm inter-element spacing and a burst pulse of 100 ns duration were used. Two elements wide transmission aperture was used to generate an ultrasound wave covering the full image region. The comparison of 2D ultrasound images of a tissue mimicking phantom obtained using the STA and MSTA methods is presented to demonstrate the benefits of the second one.

Go to article

Authors and Affiliations

Ihor Trots
Marcin Lewandowski
Yuriy Tasinkevych
Andrzej Nowicki
Download PDF Download RIS Download Bibtex

Abstract

There is a considerable increase in the use of noise barriers in recent years. Noise barriers as a control noise solution can increase the insertion loss to protect receivers. This paper presents the results of an investigation about the acoustic efficiency of primitive root sequence diffuser (PRD) on an environmental single T-shape barrier design. A 2D boundary element method (BEM) is used to predict the insertion loss of the tested barriers. The results of rigid and with a different sequence diffuser coverage are also predicted for comparison. Employing PRD on the top surface of T-shape barrier has been found to improve the performance of barriers in comparison with the use of rigid and QRD coverage at the examined receiver locations. It has been found that decreasing the design frequency of PRD shifts the frequency effects towards lower frequencies, and therefore the overall A-weighted insertion loss is improved. It was also found that using wire mesh with reasonably efficient resistivity on the top surface of PRD improves the efficiency of the reactive barriers; however utilizing wire meshes with flow resistivity higher than the specific acoustic impedance of air on the PRD top of a diffuser barrier significantly reduces the performance of the barrier within the frequency bandwidth of the diffuser. The performance of a PRD covered T-shape barrier at 200 Hz was found to be higher than that of its equivalent QRD barriers in both the far field and in areas close to the ground. The amount of improvement compared made by PRD barrier compared with its equivalent rigid barrier at far field is about 2 to 3 dB, while this improvement relative to the barrier model "QR4" can reach up to 4-6 dB.

Go to article

Authors and Affiliations

Mohammad Monazzam
Mahdiyeh Naderzadeh
Parvin Nassiri
Samaneh Fard
Download PDF Download RIS Download Bibtex

Abstract

n the paper, the simulation PROP5 program with the road model defined as a noise source and road surroundings model, is used to predict the efficiency of noise protecting means for the chosen building. The appropriate models of verified accuracy have been chosen by comparison of the simulation results with field measurements (Walerian et al., 2010). Here, using the pre-tested simulation program, the possibility of acoustic climate improvement has been analyzed in the ranges of practical variations of the input parameters. The road parameters: its geometry (number of lanes and their positions) and traffic structure over lanes (vehicle flow rates and their average speeds) have been taken under consideration as changeable parameters, that could be corrected to obtain acoustical climate improvement. Moreover, an acoustical screen designing has been considered. The screen efficiency has been evaluated under conditions defined by the input parameters of the road and its surroundings.

Go to article

Authors and Affiliations

Elżbieta Walerian
Ryszard Janczur
Mieczysław Czechowicz
Yulija Smyrnova
Download PDF Download RIS Download Bibtex

Abstract

The sound speed and parameters of nonlinearity B/A, C/A in a fluid are expressed in terms of coefficients in the Taylor series expansion of an excess internal energy, in powers of excess pressure and density. That allows to conclude about features of the sound propagation in fluids, the internal energy of which is known as a function of pressure and density. The sound speed and parameters of nonlinearity in the mixture consisting of boiling water and its vapor under different temperatures, are evaluated as functions of mass concentration of the vapor. The relations analogous to that in the Riemann wave in an ideal gas are obtained in a fluid obeying an arbitrary equation of state. An example concerns the van der Waals gases. An excess pressure in the reflected wave, which appears when standard or nonlinear absorption in a fluid takes place, is evaluated in an arbitrary fluid.

Go to article

Authors and Affiliations

Anna Perelomova
Paweł Wojda
Download PDF Download RIS Download Bibtex

Abstract

The pathological states of biological tissue are often resulted in attenuation changes. Thus, information about attenuating properties of tissue is valuable for the physician and could be useful in ultrasonic diagnosis. We are currently developing a technique for parametric imaging of attenuation and we intend to apply it for in vivo characterization of tissue. The attenuation estimation method based on the echoes mean frequency changes due to tissue attenuation dispersion, is presented. The Doppler IQ technique was adopted to estimate the mean frequency directly from the raw RF data. The Singular Spectrum Analysis technique was used for the extraction of mean frequency trends. These trends were converted into attenuation distribution and finally the parametric images were computed. In order to reduce variation of attenuation estimates the spatial compounding method was applied. Operation and accuracy of attenuation extracting procedure was verified by calculating the attenuation coefficient distribution using the data from the tissue phantom (DFS, Denmark) with uniform echogenicity while attenuation coefficient underwent variation.

Go to article

Authors and Affiliations

Andrzej Nowicki
Ziemowit Klimonda
Jerzy Litniewski
Download PDF Download RIS Download Bibtex

Abstract

Directional excitation of sound in an aperiodic finite baffle system is analyzed using a method developed earlier in electrostatics. The solution to the corresponding boundary value problem is obtained in the spatial-frequency domain. The acoustic pressure and normal particle velocity distribution in acoustic media can be easily computed by the inverse Fourier transform from their spatial spectra on the baffle plane. The presented method can be used for linear acoustic phased arrays modeling with finite element size and inter-element interactions taken into account. Some illustrative numerical examples presenting the far-field radiation pattern and wave-beam steering are given.

Go to article

Authors and Affiliations

Yuriy Tasinkevych

Instructions for authors

Author Guidelines
• Manuscripts intended for publication in Archives of Acoustics should be submitted in pdf format by an on-line procedure.
• Manuscript should be original, and should not be submitted either previously or simultaneously elsewhere, neither in whole, nor in part.
• Submitted papers must be written in good English and proofread by a native speaker.
• Basically, the papers should not exceed 40 000 typographic signs.
• Postal addresses, affiliations and email addresses for each author are required.
• Detailed information see Article Requirements.
• Manuscript should be accompanied by a cover letter containing the information:
o why the paper is submitted to ARCHIVES OF ACOUSTICS,
o suggestion on the field of acoustics related to the topic of the submitted paper,
o the statement that the manuscript is original, the submission has not been previously published, nor was sent to another journal for consideration,
o 3–5 names of suggested reviewers together with their affiliations, full postal and e-mail addresses; at least 3 suggested reviewers should be affiliated with other scientific institutions than the affiliations of the authors,
o author’s suggestion to classification of the paper as the research paper, review paper or technical note.

Article Requirements
1. At submission time only a PDF file is required. After acceptance, authors must submit all source material (see information about Figures). Authors can use their preferred manuscript-preparation software. The journal itself is produced in LaTeX, so accepted articles will be converted to LaTeX at production time.
2. The title of the paper should be as short as possible.
3. Full names and surnames should be given.
4. The full postal address of each affiliation, including the country name should be provided. Affiliations should contain the full postal address, as well as an e-mail address of one author designated as corresponding author.
5. The text should be preceded by a concise abstract (less than 200 words).
6. Keywords should be given.
7. The formulae to be numbered are those referred to in the paper, as well as the final formulae.
8. All notations should be written very distinctly.
9. References in the text (author(s) and year of publication) are to be cited between parentheses.
Items appearing in the reference list should be complete, including surname and the initials of the first name of the author, the full title of the paper/book in English followed by the information on the original paper language. In case of a book, the publisher's name, the place and year of publication should be given. In case of a periodical, the full title of the periodical, consecutive volume number, current issue number, pages, and year of publication should be given. All references in the bibliography should be cited in the text, and arranged in alphabetical order by authors' last name.
For more information on references see http://acoustics.ippt.gov.pl/public/Instructions.pdf.
10. Figures must be of publication quality. Each figure should be saved in separate file and captioned and numbered so that it can float. After acceptance, Authors will need to submit the original source files for all photos, diagrams and graphs in manuscript.
For diagrams and graphs vector EPS or vector PDF files are the most useful. Make sure that what you're saving is vector graphics and not a bitmap. Please also include the original data for any plots. This is particularly important if you are unable to save Excel-generated plots in vector format. Saving them as bitmaps is not useful; please send the Excel (.xls) spreadsheets instead.
Photographs should be high-quality – with resolution no lower than 300 dpi.
Pack all figure files into a single archive (zip, tar, rar or other format) and then upload on the magazine web site.

This page uses 'cookies'. Learn more