Nauki Techniczne

Opto-Electronics Review


Opto-Electronics Review | 2020 | vol. 28 | No. 1 |


Determining the dependence of phase difference modulations between light pulses in a modified Mach-Zehnder interferometer was used to develop an optical system coding the information and working as an eavesdropping sensor for an optical fibre information exchange system. The basic challenge in the system development is to maintain stable operation in changing environmental conditions, as well as to ensure optimal parameters of the phase modulator. The system was tested for various many-kilometer long transmission lines of single-mode fibres. The research was focused on achieving the normative Bit Error Rate for the system in the 100 Mbit/s range (STM-1). Such a system can be used in commercial applications for the code key secure transmission in the physical layer of the link.
Przejdź do artykułu

Autorzy i Afiliacje

M. Życzkowski
M. Karol
N. Pałka


The perovskites XBiO3 (X = Al, Ga, In) have been studied in terms of mechanical, optical and thermoelectric behavior for energy harvesting application. Density functional theory is applied to study electronic, optical and thermoelectric properties of the studied materials. Structural, mechanical and thermodynamic stabilities are confirmed from the tolerance factor, Born mechanical stability and formation energy/specific heat capacity. Poisson and Plough ratios show the studied materials are ductile and have ability to withstand pressure. Band structure analysis shows the indirect band gap 3.0/2.1/1.0 eV for ABO/GBO/IBO. A complete set of optical spectra is reported by dielectric constants, refractive index, optical conduction, absorption of light and optical loss energy. Shifting of maximum absorption band to visible region increases the potential of perovskites XBiO3. Transport characteristics are also investigated by electrical conductivity, Seebeck coefficient and figure of merit.

Przejdź do artykułu

Autorzy i Afiliacje

Q. Mahmood
S. A. Rouf
E. Algrafy
G. Murtaza
S. M. Ramay
A. Mahmood


The presented article examines aspects of a PV module testing using natural sunlight in outdoor conditions. The article discusses the physical sense of indexes: atmosphere purity, diffused component content, beam clear sky index. Procedures for their determination are given in relation to both instantaneous and daily values. Their close connection with the values of solar irradiance spectral distribution such as Average Photon Energy and Useful Fraction is demonstrated, as well as their usefulness in module testing in outdoor conditions. Their influence on the conversion of modules made from various absorbers and various technologies is demonstrated

Przejdź do artykułu

Autorzy i Afiliacje

T. Rodziewicz
M. Rajfur


This article proposes and examines a solution in which the base-station for the fifth generation radio access network is simplified by using a single millimeter-wave oscillator in the central-station and distributing its millimeter-wave signal to the base-stations. The system is designed in such a way that the low-phase-noise signal generated by an opto-electronic oscillator is transmitted from the central-station to multiple base-stations via a passive optical network infrastructure. A novel flexible approach with a single-loop opto-electronic oscillator at the transmitting end and a tunable dispersion-compensation module at the receiving end(s) is proposed to distribute a power-penalty-free millimeter-wave signal in the radio access network. Power-penalty-free signal transmission from 10 MHz up to 45 GHz with an optical length of 20 km is achieved by a combination of a tunable dispersion-compensation module and an optical delay line. In addition, measurements with a fixed modulation frequency of 39 GHz and discretely incrementing optical fiber lengths from 0.625 km to 20 km are shown. Finally, a preliminary idea for an automatically controlled feedback-loop tuning system is proposed as a further research entry point.

Przejdź do artykułu

Autorzy i Afiliacje

M. A. Ilgaz
K. Vuk Baliž
B. Batagelj


The solar photovoltaic technology is one of the renewable technologies with the potential to shape a future-proof, reliable, scalable and affordable electricity system. It is important to provide better resources for any upcoming technology. CdS/CdTe thin films have long been considered as one enticing option for reliable and cost-effective solar cells to be developed. N-type CdS as a transparent window layer in heterojunction structures is one of the best choices for CdTe cells. In a solar cell structure, window layer material plays a very crucial role to improve its performance. For this reason, this review focuses on the basic and significant aspects such as importance of the window layer thickness, degradation effect, use of nano-wire arrays, and an ammonia-free process to deposit the window layer. Also, an attempt has been made to analyze various processes improving window layer properties. Necessary discussions have been included to review the impact of solar cell parameters on the above aspects. It is anticipated that this review article will fulfill the requirement of knowledge to be used in the fabrication of CdS/CdTe solar cells.

Przejdź do artykułu

Autorzy i Afiliacje

D. Lilhare
A. Khare


Opto-Electronics Review - Editorial Board

L. R. JAROSZEWICZ, Military University of Technology, Warsaw, Poland

Deputy Editor-in Chief:
P. MARTYNIUK, Military University of Technology, Warsaw, Poland

Board of Co-editors:

Optical Design and Applications
V.O. ANGELSKY, Chernivtsi National University, Chernivtsi, Ukraine

Image Processing
M. JÓŹWIK, Warsaw University of Technology, Warsaw, Poland

T. ANTOSIEWICZ, Warsaw University, Warsaw, Poland

Modelling of Optoelectronic Devices. Semiconductor Lasers
M. DEMS, Łódź Technical University, Łódź, Poland

Optoelectronics Materials
D. DOROSZ, AGH University of Science and Technology, Cracow, Poland

Micro-Opto-Electro-Mechanical Systems
T.P. GOTSZALK, Wrocław University of Technology, Wrocław, Poland

Infrared Physics and Technology <
M. KOPYTKO, Military University of Technology, Warsaw, Poland

Technology and Fabrication of Optoelectronic Devices
J. MUSZALSKI, Institute of Electron Technology, Warsaw, Poland

Photonic Crystals
K. PANAJOTOV, Vrije Universiteit Brussels, Brussels, Belgium

Laser Physics, Technology and Applications
J. ŚWIDERSKI, Warsaw University of Technology, Warsaw, Poland

Optical Sensors and Applications
M. ŚMIETANA, Warsaw University of Technology, Warsaw, Poland

A. IWAN, Military Institute of Engineer Technology, Wroclaw, Poland

Biomedical Optics and Photonics
A. LIEBERT, Institute of Biocybernetics and Biomedical Engineering, Warsaw, Poland

International Editorial Advisory Board

D. BIMBERG, Technische Universitaet Berlin, Berlin, Germany

F. CAPASSO, Harvard University, Cambridge, USA

A.I. DIROCHKA, Production Center ORION, Moscow, Russia

P.G. ELISEEV, University of New Mexico, Albuquerque, USA

P. HARING−BOLIVAR, University of Siegen, Siegen, Germany

M. HENINI, University of Nottingham, Nottingham, England

B. JASKORZYNSKA, Royal Institute of Technology, Kista, Sweden

M. KIMATA, Ritsumeikan University, Shiga, Japan

R. KLETTE, University of Auckland, Auckland, New Zealand

S. KRISHNA, University of New Mexico, Albuquerque, USA

H.C. LIU, Shanghai Jiao Tong University, Shanghai, China

J. MISIEWICZ, Wrocław University of Technology, Wrocław, Poland

E. OZBAY, Bilkent University, Ankara, Turkey

J.G. PELLEGRINI, Night Vision and Electronic Sensors Directorate, Fort Belvoir, USA

M. RAZEGHI, Northwestern University, Evanston, USA

A. ROGALSKI, Military University of Technology, Warsaw, Poland

P. RUSSELL, Max Planck Institute for the Science of Light, Erlangen, Germany

V. RYZHII, University of Aizu, Aizu, Japan

C. SIBILIA, Universita' di Roma “La Sapienza”, Roma, Italy

A. TORRICELLI, Politecnico di Milano, Milano, Italy

T. WOLIŃSKI, Warsaw University of Technology, Warsaw, Poland

W. WOLIŃSKI, Warsaw University of Technology, Warsaw, Poland

S.−T. WU, University of Central Florida, Orlando, USA

Y.P. YAKOVLEV, Ioffe Physicotechnical Institute, St. Petersburg, Russia

J. ZIELŃSKI, Military University of Technology, Warsaw, Poland

Language Editor

J. Kulesza, e-mail:

Technical Editors:

R.Podraza, e-mail:

E.Sadowska, e-mail:


Military University of Technology,

Gen. Sylwestra Kaliskiego St. 2,

00 – 908 Warsaw, Poland

Instrukcje dla autorów

Polityka Open Access

Opto-Electronics Review is an open access journal with all content available with no charge for readers in full text version. The journal content is available under the licencse CC BY-SA 4.0

Dodatkowe informacje

Opto-Electronics Review was established in 1992 for the publication of scientific papers concerning optoelectronics and photonics materials, system and signal processing. This journal covers the whole field of theory, experimental verification, techniques and instrumentation and brings together, within one journal, contributions from a wide range of disciplines. Papers covering novel topics extending the frontiers in optoelectronics and photonics are very encourage. The main goal of this magazine is promotion of papers presented by European scientific teams, especially those submitted by important team from Central and Eastern Europe. However, contributions from other parts of the world are by no means excluded.

Articles are published in OPELRE in the following categories:

-invited reviews presenting the current state of the knowledge,

-specialized topics at the forefront of optoelectronics and photonics and their applications,

-refereed research contributions reporting on original scientific or technological achievements,

-conference papers printed in normal issues as invited or contributed papers.

Authors of review papers are encouraged to write articles of relevance to a wide readership including both those established in this field of research and non-specialists working in related areas. Papers considered as “letters” are not published in OPELRE.

Opto-Electronics Review is published quarterly as a journal of the Association of Polish Electrical Engineers (SEP) and Polish Academy of Sciences (PAS) in cooperation with the Military University of Technology and under the auspices of the Polish Optoelectronics Committee of SEP.

Abstracting and Indexing:

Current Contents - Physical, Chemical & Earth Sciences

Current Contents - Engineering, Technology & Applied Sciences

Science Citation Index Expanded

Journal Citation Reports - Science Edition



Policies and ethics:

The editors of the journal place particular emphasis on compliance with the following principles:

Authorship of the paper: Authorship should be limited to those who have made a significant contribution to the conception, design, execution, or interpretation of the reported study.

Originality and plagiarism: The authors should ensure that they have written entirely original works, and if the authors have used the work and/or words of others, that this has been appropriately cited or quoted.

Data access and retention: Authors may be asked to provide the raw data in connection with a paper for editorial review, and should be prepared to provide public access to such data.

Multiple, redundant or concurrent publication: An author should not in general publish manuscripts describing essentially the same research in more than one journal or primary publication.

Acknowledgement of sources: Proper acknowledgment of the work of others must always be given.

Disclosure and conflicts of interest: All submissions must include disclosure of all relationships that could be viewed as presenting a potential conflict of interest.

Fundamental errors in published works: When an author discovers a significant error or inaccuracy in his/her own published work, it is the author's obligation to promptly notify the journal editor or publisher and cooperate with the editor to retract or correct the paper.

Reporting standards: Authors of reports of original research should present an accurate account of the work performed as well as an objective discussion of its significance.

Hazards and human or animal subjects: Statements of compliance are required if the work involves chemicals, procedures or equipment that have any unusual hazards inherent in their use, or if it involves the use of animal or human subjects.

Use of patient images or case details: Studies on patients or volunteers require ethics committee approval and informed consent, which should be documented in the paper.

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji