Nauki Techniczne

Opto-Electronics Review

Zawartość

Opto-Electronics Review | 2020 | vol. 28 | No. 4 |

Abstrakt

ZnO thin layers were deposited on p-type silicon substrates by the sol-gel spin-coating method and, then, annealed at various temperatures in the range of 573–873 K. Photoluminescence was carried out in the temperature range of 20–300 K. All samples showed two dominant peaks that have UV emissions from 300 nm to 400 nm and visible emissions from 400 nm to 800 nm. Influence of temperature on morphology and chemical composition of fabricated thin layers was examined by XRD, SEM, FTIR, and Raman spectroscopy. These measurements indicate that ZnO structure is obtained for samples annealed at temperatures above 573 K. It means that below this temperature, the obtained thin films are not pure zinc oxide. Thus, annealing temperature significantly affected crystallinity of the thin films.

Przejdź do artykułu

Autorzy i Afiliacje

M. Sypniewska
R. Szczesny
P. Popielarski
K. Strzalkowski
B. Derkowska-Zielinska

Abstrakt

In this article, synthesis, electronic and optical properties of an N-cyclohexyl-acrylamide (NCA) molecule are described based on different solvent environments and supported by theoretical calculations. Theoretical calculations have been carried out using a density function theory (DFT). Temperature dependence of the sample electrical resistance has been obtained by a four-point probe technique. Experimental and semi-theoretical parameters such as optical density, transmittance, optical band gap, refractive index of the NCA for different solvents were obtained. Both optical values and electrical resistance values have shown that NCA is a semiconductor material. The values of HOMO and LUMO energy levels of the headline molecule indicate that it can be used as the electron transfer material in OLEDs. All results obtained confirm that the NCA is a candidate molecule for OLED and optoelectronic applications.

Przejdź do artykułu

Autorzy i Afiliacje

E. Tanış
N. Çankaya

Abstrakt

The paper describes a research on assessing the quality of edges resulting from the interaction of laser pulses with a material of rigid and flexible printed circuits. A modern Nd:YVO4 crystal diode-pumped solid-state laser generating a 532 nm wavelength radiation with a nanosecond pulse time was used for the research. Influence of laser parameters such as beam power and pulse repetition frequency on a heat affected zone and carbonization was investigated. Quality and morphology of laser-cut substrates were analyzed by optical microscopy. High quality laser cutting of printed circuit board substrates was obtained without delamination and surface damage, with a minimal carbonization and heat affected zone. The developed process was implemented on the printed circuit assembly line.

Przejdź do artykułu

Autorzy i Afiliacje

P. Ciszewski
M. Sochacki

Abstrakt

The presented work proposes a new dimming control schemes for indoor visible light communication which combines variable pulse-position modulation, colour shift keying as key schemes of IEEE 802.15.7 standard, and sub carrier-pulse-position modulation as a pulse-position modulation variant with orthogonal frequency division multiplexing. These schemes are then compared with traditional merging schemes utilizing pulse-width modulation and multiple pulse-position modulation with m-ary quadrature amplitude modulation OFDM. The proposed schemes are investigated in a typical room with a different lighting layout (i.e., distinctive and uniform lighting layout), followed by an illumination investigation to evaluate the performance of the proposed schemes, especially the enhanced achieved data rates, and to determine their limitations as reliable visible light communication systems that can satisfy both communication and illumination requirements.

Przejdź do artykułu

Autorzy i Afiliacje

Nazmi A. Mohammed
Kareem A. Badawi
Ashraf A. M. Khalaf
S. El-Rabaie

Abstrakt

This paper presents a detailed review on a present confused situation related to defining and measurement of the eyepiece diopter range of optical/electro-optical devices to be used for a direct observation by human observers. On the basis of this review three precise definitions of a direct view imagers eyepiece diopter are presented. One of these definitions is determined as optimal fit to describe the perception of human observers. Further on, design and measurement uncertainties of diopter meters are discussed and rules of accurate measurements are formulated. Finally, recommendations for the maximum acceptable errors of the diopter scale of eyepieces of classic types of direct view imagers are presented, as well.

Przejdź do artykułu

Autorzy i Afiliacje

K. Chrzanowski

Redakcja

Opto-Electronics Review - Editorial Board

Editor-in-Chief:
L. R. JAROSZEWICZ, Military University of Technology, Warsaw, Poland

Deputy Editor-in Chief:
P. MARTYNIUK, Military University of Technology, Warsaw, Poland


Board of Co-editors:

Optical Design and Applications
V.O. ANGELSKY, Chernivtsi National University, Chernivtsi, Ukraine

Image Processing
M. JÓŹWIK, Warsaw University of Technology, Warsaw, Poland

Metamaterials
T. ANTOSIEWICZ, Warsaw University, Warsaw, Poland

Modelling of Optoelectronic Devices. Semiconductor Lasers
M. DEMS, Łódź Technical University, Łódź, Poland

Optoelectronics Materials
D. DOROSZ, AGH University of Science and Technology, Cracow, Poland

Micro-Opto-Electro-Mechanical Systems
T.P. GOTSZALK, Wrocław University of Technology, Wrocław, Poland

Infrared Physics and Technology <
M. KOPYTKO, Military University of Technology, Warsaw, Poland

Technology and Fabrication of Optoelectronic Devices
J. MUSZALSKI, Institute of Electron Technology, Warsaw, Poland

Photonic Crystals
K. PANAJOTOV, Vrije Universiteit Brussels, Brussels, Belgium

Laser Physics, Technology and Applications
J. ŚWIDERSKI, Warsaw University of Technology, Warsaw, Poland

Optical Sensors and Applications
M. ŚMIETANA, Warsaw University of Technology, Warsaw, Poland

Photovoltaics
A. IWAN, Military Institute of Engineer Technology, Wroclaw, Poland

Biomedical Optics and Photonics
A. LIEBERT, Institute of Biocybernetics and Biomedical Engineering, Warsaw, Poland


International Editorial Advisory Board


D. BIMBERG, Technische Universitaet Berlin, Berlin, Germany

F. CAPASSO, Harvard University, Cambridge, USA

A.I. DIROCHKA, Production Center ORION, Moscow, Russia

P.G. ELISEEV, University of New Mexico, Albuquerque, USA

P. HARING−BOLIVAR, University of Siegen, Siegen, Germany

M. HENINI, University of Nottingham, Nottingham, England

B. JASKORZYNSKA, Royal Institute of Technology, Kista, Sweden

M. KIMATA, Ritsumeikan University, Shiga, Japan

R. KLETTE, University of Auckland, Auckland, New Zealand

S. KRISHNA, University of New Mexico, Albuquerque, USA

H.C. LIU, Shanghai Jiao Tong University, Shanghai, China

J. MISIEWICZ, Wrocław University of Technology, Wrocław, Poland

E. OZBAY, Bilkent University, Ankara, Turkey

J.G. PELLEGRINI, Night Vision and Electronic Sensors Directorate, Fort Belvoir, USA

M. RAZEGHI, Northwestern University, Evanston, USA

A. ROGALSKI, Military University of Technology, Warsaw, Poland

P. RUSSELL, Max Planck Institute for the Science of Light, Erlangen, Germany

V. RYZHII, University of Aizu, Aizu, Japan

C. SIBILIA, Universita' di Roma “La Sapienza”, Roma, Italy

A. TORRICELLI, Politecnico di Milano, Milano, Italy

T. WOLIŃSKI, Warsaw University of Technology, Warsaw, Poland

W. WOLIŃSKI, Warsaw University of Technology, Warsaw, Poland

S.−T. WU, University of Central Florida, Orlando, USA

Y.P. YAKOVLEV, Ioffe Physicotechnical Institute, St. Petersburg, Russia

J. ZIELŃSKI, Military University of Technology, Warsaw, Poland


Language Editor

J. Kulesza, e-mail: jolanta.kulesza@wat.edu.pl


Technical Editors:

R.Podraza, e-mail: renata.podraza@wat.edu.pl

E.Sadowska, e-mail: elzbieta.sadowska@wat.edu.pl

Kontakt

Military University of Technology,

Gen. Sylwestra Kaliskiego St. 2,

00 – 908 Warsaw, Poland

opelre@wat.edu.pl

Instrukcje dla autorów

Polityka Open Access

Opto-Electronics Review is an open access journal with all content available with no charge for readers in full text version. The journal content is available under the licencse CC BY-SA 4.0

Dodatkowe informacje

Opto-Electronics Review was established in 1992 for the publication of scientific papers concerning optoelectronics and photonics materials, system and signal processing. This journal covers the whole field of theory, experimental verification, techniques and instrumentation and brings together, within one journal, contributions from a wide range of disciplines. Papers covering novel topics extending the frontiers in optoelectronics and photonics are very encourage. The main goal of this magazine is promotion of papers presented by European scientific teams, especially those submitted by important team from Central and Eastern Europe. However, contributions from other parts of the world are by no means excluded.

Articles are published in OPELRE in the following categories:

-invited reviews presenting the current state of the knowledge,

-specialized topics at the forefront of optoelectronics and photonics and their applications,

-refereed research contributions reporting on original scientific or technological achievements,

-conference papers printed in normal issues as invited or contributed papers.

Authors of review papers are encouraged to write articles of relevance to a wide readership including both those established in this field of research and non-specialists working in related areas. Papers considered as “letters” are not published in OPELRE.

Opto-Electronics Review is published quarterly as a journal of the Association of Polish Electrical Engineers (SEP) and Polish Academy of Sciences (PAS) in cooperation with the Military University of Technology and under the auspices of the Polish Optoelectronics Committee of SEP.

Abstracting and Indexing:

Current Contents - Physical, Chemical & Earth Sciences

Current Contents - Engineering, Technology & Applied Sciences

Science Citation Index Expanded

Journal Citation Reports - Science Edition

Scopus

INSPEC

Policies and ethics:

The editors of the journal place particular emphasis on compliance with the following principles:

Authorship of the paper: Authorship should be limited to those who have made a significant contribution to the conception, design, execution, or interpretation of the reported study.

Originality and plagiarism: The authors should ensure that they have written entirely original works, and if the authors have used the work and/or words of others, that this has been appropriately cited or quoted.

Data access and retention: Authors may be asked to provide the raw data in connection with a paper for editorial review, and should be prepared to provide public access to such data.

Multiple, redundant or concurrent publication: An author should not in general publish manuscripts describing essentially the same research in more than one journal or primary publication.

Acknowledgement of sources: Proper acknowledgment of the work of others must always be given.

Disclosure and conflicts of interest: All submissions must include disclosure of all relationships that could be viewed as presenting a potential conflict of interest.

Fundamental errors in published works: When an author discovers a significant error or inaccuracy in his/her own published work, it is the author's obligation to promptly notify the journal editor or publisher and cooperate with the editor to retract or correct the paper.

Reporting standards: Authors of reports of original research should present an accurate account of the work performed as well as an objective discussion of its significance.

Hazards and human or animal subjects: Statements of compliance are required if the work involves chemicals, procedures or equipment that have any unusual hazards inherent in their use, or if it involves the use of animal or human subjects.

Use of patient images or case details: Studies on patients or volunteers require ethics committee approval and informed consent, which should be documented in the paper.

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji