Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 13
items per page: 25 50 75
Sort by:

Abstract

Osteocalcin is a major non-collagenous component of the bone extracellular matrix and is considered to be an indicative factor of osteoblast differentiation. In the present study, we detected osteocalcin expression in different antler areas and growth phases by immunohisto- chemistry. Osteocalcin was highly expressed in all areas during the mineralization period and in mesenchymal cell and chondrocyte areas during the rapid growth period. The nucleotide sequence of the osteocalcin gene in sika deer antler was determined. The open reading frame was 303 bp encoding a protein of 100 amino acids. The estimated molecular mass of osteocalcin was 10.38 kDa and the theoretical isoelectric point was 5.37. The osteocalcin gene with a 6× His-tag at the C-terminus was cloned into the pGEX-4T1 vector and expressed in Escherichia coli under optimal conditions. The recombinant soluble protein fused with GST was purified with Ni-NTA resin. The purified osteocalcin protein exhibited a significant increase in HA adhesion and promoted antler chondrocyte proliferation. Osteocalcin is an important factor in regulating the rapid growth and differentiation of deer antlers.
Go to article

Abstract

In the current study, twenty lambs, aged 4 months, half male and half female, were classified into four groups, with five in each group. The experimental three groups of lambs were given intravenous (IV), intramuscular (IM) and subcutaneous (SC) administrations of recombinant ovine interferon-τ (roIFN-τ). The fourth group (normal control) of lambs was given normal saline injections in the same way. After administrations, blood samples were collected from the tested animals at different time points post injection, and the serum titers of roIFN-τ were measured using cytopathic effect (CPE) inhibition bioassay. The results of calculating pharmacokinetic (PK) parameters using DAS software showed that the PK characteristics of roIFN-τ through IV injection conformed to the two-compartment open model, whose half-life of distribution phases (T1/2α) was 0.33±0.034 h and the elimination half-life(T1/2β) was 5.01±0.24 h. However, the PK features of IM injection and SC injection of roIFN-τ conformed to the one compartment open model, whose Tmax were 3.11±0.26 h and 4.83±0.43 h, respectively, together with an elimination half life(T1/2β) of 9.11±0.76 h and 7. 43±0.58 h, and an absorption half-life (T1/2k(a)) of 1.13±0.31 h and 1.85±0.40 h, respectively. The bioavailability of roIFN-τ after IM administration reaches 73.57%, which is greater than that of SC administration (53.43%). These results indicate that the drug administration effect can be preferably obtained following a single dose IM administration of the roIFN-τ aqueous preparation. This study will facilitate the clinical application of roIFN-τ as a potential antiviral agent in future work.
Go to article

Abstract

In order to predict the distribution of shrinkage porosity in steel ingot efficiently and accurately, a criterion R√L and a method to obtain its threshold value were proposed. The criterion R√L was derived based on the solidification characteristics of steel ingot and pressure gradient in the mushy zone, in which the physical properties, the thermal parameters, the structure of the mushy zone and the secondary dendrite arm spacing were all taken into consideration. The threshold value of the criterion R√L was obtained with combination of numerical simulation of ingot solidification and total solidification shrinkage rate. Prediction of the shrinkage porosity in a 5.5 ton ingot of 2Cr13 steel with criterion R√L>0.21 m・℃1/2・s -3/2 agreed well with the results of experimental sectioning. Based on this criterion, optimization of the ingot was carried out by decreasing the height-to-diameter ratio and increasing the taper, which successfully eliminated the centreline porosity and further proved the applicability of this criterion.
Go to article

Abstract

Copper slag is a by-product obtained during smelting and refining of copper. Copper smelting slag typically contains about 1 wt.% copper and 40 wt.% iron depending upon the initial ore quality and the furnace type. Main components of copper slag are iron oxide and silica. These exist in copper slag mainly in the form of fayalite (2FeO ·SiO2). This study was intended to recover pig iron from the copper smelting slag by reduction smelting method. At the reaction temperature of below 1400°С the whole copper smelting slag was not smelted, and some agglomerated, showing a mass in a sponge form. The recovery behavior of pig iron from copper smelting slag increases with increasing smelting temperature and duration. The recovery rate of pig iron varied greatly depending on the reaction temperature.
Go to article

This page uses 'cookies'. Learn more