Wyniki wyszukiwania

Filtruj wyniki

  • Czasopisma
  • Autorzy publikacji
  • Słowa kluczowe
  • Data
  • Typ

Wyniki wyszukiwania

Wyników: 11
Wyników na stronie: 25 50 75
Sortuj wg:

Abstrakt

While analyzing shape accuracy of ferroalloy precision castings in terms of ceramic moulds physical anisotropy, low-alloy steel castings ("cover") and cast iron ("plate") were included. The basic parameters in addition to the product linear shape accuracy are flatness deviations, especially due to the expanded flat surface which is cast plate. For mentioned castings surface micro-geometry analysis was also carried, favoring surface load capacity tp50 for Rmax = 50%. Surface load capacity tp50 obtained for the cast cover was compared with machined product, and casting plate surface was compared with wear part of the conveyor belt. The results were referred to anisotropy of ceramic moulds physical properties, which was evaluated by studying ceramic moulds samples in computer tomography equipment Metrotom 800.
Przejdź do artykułu

Abstrakt

Substituting of ethyl silicate with ecologic sols of colloidal silica in the investment casting technology, resulting from the increased demands concerning environmental protection, caused the prolongation of production cycle for precision castings produced in multi-layer thin-walled ceramic shell moulds. Modification of Sizol 030 binder with benzoyl peroxide, proposed in the paper, was aimed at restriction of time needed for realization of a single layer of the shell mould, and by the same, of such a mould as a whole. Examination of kinetics of the drying process were held for the layers made of prepared moulding material and the influence of binder modification on the mould curing time was determined.
Przejdź do artykułu

Abstrakt

The process of enrichment in a jig has usually been described and analysed using particle density as a separation feature. However, a degree of particle loosening in the jig bed is affected by, inter alia, the terminal particle free settling velocity which in turn is affected by the size, density and shape of a particle. Therefore, the terminal particle settling velocity clearly characterises the feed transferred to a jig for the enrichment process. Taking the comprehensive particle geometric (particle size and shape) and physical properties (particle density) into account comes down to the calculation of the terminal particle settling velocity. The terminal particle settling velocity is therefore a complex separation feature which comprises three basic particle features (particle density, size and shape). This paper compares the effects of enrichment of coal fines in a jig, for two cases: when the commonly applied particle density is separation feature and for the particle settling velocity. Particle settling velocities were calculated in the selected three particle size fractions: –3.15+2.00, –10.00+8.00 and –20.00+16.00 mm based on the industrial testing of a jig for coal fines and detailed laboratory tests consisting in determining particle density, projective diameter and volume and dynamic particle shape coefficient. The calculated and drawn partition curves for two variants, i.e. when particle density and particle settling velocity were taken into account as the separation argument in selected particle size fractions, allowed to calculate and compare separation precision indicator. With the use of a statistical test, the assumption on the independence of random variables of the distribution of components included in the distribution of the particle settling velocity as a separation feature during enrichment in a jig was verified.
Przejdź do artykułu

Abstrakt

Inconel 713C precision castings are used as aircraft engine components exposed to high temperatures and the aggressive exhaust gas environment. Industrial experience has shown that precision-cast components of such complexity contain casting defects like microshrinkage, porosity, and cracks. This necessitates the development of repair technologies for castings of this type. This paper presents the results of metallographic examinations of melted areas and clad welds on the Inconel 713C nickel-based superalloy, made by TIG, plasma arc, and laser. The cladding process was carried out on model test plates in order to determine the technological and materialrelated problems connected with the weldability of Inconel 713C. The studies included analyses of the macro- and microstructure of the clad welds, the base materials, and the heat-affected zones. The results of the structural analyses of the clad welds indicate that Inconel 713C should be classified as a low-weldability material. In the clad welds made by laser, cracks were identified mainly in the heat-affected zone and at the melted zone interface, crystals were formed on partially-melted grains. Cracks of this type were not identified in the clad welds made using the plasma-arc method. It has been concluded that due to the possibility of manual cladding and the absence of welding imperfections, the technology having the greatest potential for application is plasma-arc cladding.
Przejdź do artykułu

Abstrakt

In technology of coal fines beneficiation in Poland mainly fines jigging processes are in use. In case of steam coal fines beneficiation it is till 80% of the whole amount of produced assortments, while in case of coking coal fines it is 100%. The necessary condition of not homogenous feed separation which is directed to beneficiation process in pulsating water stream is a sufficient liberation of particles. The stratification of particles in working bed causes that particles of certain size, density and shape gather in individual layers in working bed of jig. The introduction of sufficient amount of additional water determines appropriate liberation of particles group, which generates partition into concentrate and tailings. The paper presents the results of sampling of industrial jig used for the beneficiation of coal fines by three various settings of additional amount of water under sieve which is directed to jigging. These amounts were equal to 35, 50 and 70 [m3/h]. Collected samples of separation products were then sieved into narrow particle size fractions and divided into density fractions. In such narrow size-density fractions the coordinates of partition curves were calculated for tailings of hard coal fines, which were subsequently approximated by means of Weibull distribution function. The separation precision measured by separation density, probable error and imperfection were determined on the basis of obtained model separation curves. The evaluation of separation effects was performed for a wide particle size fraction: feed directed to jigging process and narrow particle size fractions. The analysis of separation results in size-density fractions allowed to determine the influence of particle size change on the value of probable error. The results of separation precision in size-density fractions were compared with effects of separation of wide particle fraction, i.e. feed directed to jigging process.
Przejdź do artykułu

Abstrakt

The study presents the results of the investigations of the effect of Cu, Ni, Cr, V, Mo and W alloy additions on the microstructure and mechanical properties of the AlSi7Mg0.3 alloy. The examinations were performed within a project the aim of which is to elaborate an experimental and industrial technology of producing elements of machines and devices complex in their construction, made of aluminium alloys by the method of precision investment casting. It was demonstrated that a proper combination of alloy additions causes the crystallization of complex intermetallic phases in the silumin, shortens the SDAS and improves the strength properties: Rm, Rp0.2,HB hardness. Elevating these properties reduces At, which, in consequence, lowers the quality index Q of the alloy of the obtained casts. Experimental casts were made in ceramic moulds preliminarily heated to 160 °C, into which the AlSi7Mg0.3 alloy with the additions was cast, followed by its cooling at ambient temperature. With the purpose of increasing the value of the quality index Q, it is recommended that the process of alloy cooling in the ceramic mould be intensified and/or a thermal treatment of the casts be performed (ageing)(T6).
Przejdź do artykułu

Abstrakt

The study discusses the issues connected with the production of thin-walled ceramic slurry in the replicast cs technology. In the ceramic mould production process, a special role is played by the liquid ceramic slurry used to produce the first layer of the mould. The study examines selected technological properties of liquid ceramic slurries used to produce moulds in the replicas cs technology. The ceramic slurries for the tests were prepared based on the binders Ludox Px30 and Sizol 030, enriched with Refracourse flour. The wettability of the pattern's surface by the liquid ceramic slurry and the dependence of the apparent viscosity on the ceramic flour content in the mixture were determined. The wettability of the pattern surface by the liquid ceramic slurry was determined based on the measurement of the wetting angle. The angle was determined by means of an analysis of the computer image obtained with the use of a CDC camera.
Przejdź do artykułu

Abstrakt

The article presents the results of a comparative analysis of the metal substructure for dental prosthesis made from a Co-Cr-Mo-W alloy by two techniques, i.e. precision investment casting and selective laser melting (SLM). It was found that the roughness of the raw surface of the SLM sinter is higher than the roughness of the cast surface, which is compensated by the process of blast cleaning during metal preparation for the application of a layer of porcelain. Castings have a dendritic structure, while SLM sinters are characterized by a compact, fine-grain microstructure of the hardness higher by about 100 HV units. High performance and high costs of implementation the SLM technology are the cause to use it for the purpose of many dental manufacturers under outsourcing rules. The result is a reduction in manufacturing costs of the product associated with dental work time necessary to scan, designing and treatment of sinter compared with the time needed to develop a substructure in wax, absorption in the refractory mass, casting, sand blasting and finishing. As a result of market competition and low cost of materials, sinter costs decrease which brings the total costs related to the construction unit making using the traditional method of casting, at far less commitment of time and greater predictability and consistent sinter quality.
Przejdź do artykułu

Abstrakt

Inconel 713C alloy belongs to the group of materials with high application potential in the aerospace industry. This nickel alloy has excellent features such as high strength, good surface stability, high creep and corrosion resistance. The paper presents the results of metallographic examinations of a base material and padding welds made by laser beam on the Inconel 713C alloy. The tests were made on precisely cast test plates imitating low - pressure turbine blades dedicated for the aerospace industry. Observations of the macro- and microstructure of the padding welds, heat-affected zone and base material indicate, that the Inconel 713C alloy should be classified as a hard-to-weld material. In the investigated joint, cracking of the material is disclosed mainly in the heat-affected zone and at the melted zone interface, where pad weld crystals formed on partially melted grains. The results show that phases rich with chromium and molybdenum were formed by high temperature during welding process, which was confirmed by EDS analysis of chemical composition.
Przejdź do artykułu

Abstrakt

This research work is devoted to the theoretical study of the pipe calibration on a mandrel. The aim of the study is to improve the precision of the calibrated pipes. As the paper shows, it is advisable to apply different methods of research depending on the purpose of the study of metal forming processes: mathematical, computer or physical simulation. Analytical review of existing mathematical models of the pipes calibration on a mandrel showed that the set of assumptions adopted in the mathematical modeling does not allow assessing the precision of the pipes during calibration. Therefore, finite-element method simulation package was used for this research. Research method and pipes precision index were developed on the basis of the computer simulation using Deform-3D package. The investigations have allowed us to get the dependence of the pipe precision on technological factors and to identify the root cause of reduced efficiency calibration – extrafocal deformation.
Przejdź do artykułu

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji