Underground mining extraction causes the displacement and changes of stress fields in the surrounding rock mass. The determination of the changes is extremely important when the mining activity takes place in the proximity of post-flotation tailing ponds, which may affect the stability of the tailing dams. The deterministic modeling based on principles of continuum mechanics with the use of numerical methods, e.g. finite element method (FEM) should be used in all problems of predicting rock mass displacements and changes of stress field, particularly in cases of complex geology and complex mining methods. The accuracy of FEM solutions depends mainly on the quality of geomechanical parameters of the geological strata. The parameters, e.g. young modulus of elasticity, may require verification through a comparison with measured surface deformations using geodetic methods. This paper presents application of FEM in predicting effects of underground mining on the surface displacements in the area of the KGHM safety pillar of the tailing pond of the OUOW Żelazny Most. The area has been affected by room and pillar mining with roof bending in the years 2008-2016 and will be further exposed to room-and-pillar extraction with hydraulic filling in the years 2017–2019.
The paper presents a new geotechnical solution indicating a possibility of effective building structures protection. The presented solutions enable minimization of negative effects of underground mining operations. Results of numerical modelling have been presented for an example of design of preventive ditches reducing the influence of mining operations on the ground surface. To minimize the mining damage or to reduce its reach it is reasonable to look for technical solutions, which would enable effective protection of building structures. So far authors concentrated primarily on the development of building structure protection methods to minimize the damage caused by the underground mining. The application of geotechnical methods, which could protect building structures against the mining damage, was not considered so far in scientific papers. It should be noticed that relatively few publications are directly related to those issues and there are no practical examples of effective geotechnical protection. This paper presents a geotechnical solution indicating a possibility of effective protection of building structures. The presented solutions enable minimization of negative effects of underground mining operations. Results of numerical modelling have been presented for an example of design of preventive ditches reducing the influence of mining operations on the ground surface. The calculations were carried out in the Abaqus software, based on the finite element method.
An analysis of the impact of mining with caving on the surface shows that a type of rock mass strata seems to be one of the critical factors affecting the process. Correlating the values of mining-induced surface deformation with the rock mass structure and the state of its disturbance is of crucial importance. Therefore, if other mining conditions are left unaffected, then those factors exert the key influence on a course and distribution of subsidence and rock mass deformation. A proper description of rock mass type and properties also seems rational for a proper determination of prediction parameters, especially in the case of a multi-seam coal mining, and/or the exploitation carried out at considerable depths. A general outcome of the study discussed in this paper is the development of the methodology and model practices for determining the rock mass type and, as a result, for selecting the optimal values of parameters for predicting the values of surface subsidence in relation to particular geological and mining conditions. The study proves that the type of rock mass may be described by such factors as the influence of overburden strata, the influence of Carboniferous layers, the disturbance of rock mass and the depth of exploitation.
Geodesic measurements of mining area deformations indicate that their description fails to be regular, as opposed to what the predictions based on the relationships of the geometric-integral theory suggest. The Knothe theory, most commonly applied in that case, considers such parameters as the exploitation coefficient a and the angle of the main influences range tgβ, describing the geomechanical properties of the medium, as well as the mining conditions. The study shows that the values of the parameters a = 0.8 and tgβ = 2.0, most commonly adopted for the prediction of surface deformation, are not entirely adequate in describing each and every mining situation in the analysed rock mass. Therefore, the paper aims to propose methodology for determining the value of exploitation coefficient a, which allows to predict the values of surface subsidence caused by underground coal mining with roof caving, depending on geological and mining conditions. The characteristics of the analysed areas show that the following factors affect surface subsidence: thickness of overburden, type of overburden strata, type of Carboniferous strata, rock mass disturbance and depth of exploitation. These factors may allow to determine the exploitation coefficient a, used in the Knothe theory for surface deformation prediction.