This paper presents the results of numerical analysis of aerodynamic characteristics of a sports car equipped with movable aerodynamic elements. The effects of size, shape, position, angle of inclination of the moving flaps on the aerodynamic downforce and aerodynamic drag forces acting on the vehicle were investigated. The calculations were performed with the help of the ANSYS-Fluent CFD software. The transient flow of incompressible fluid around the car body with moving flaps, with modeled turbulence (model Spalart-Allmaras or SAS), was simulated. The paper presents examples of effective flap configuration, and the example of configuration which does not generate aerodynamic downforce. One compares the change in the forces generated at different angles of flap opening, pressure distribution, and visualization of streamlines around the body. There are shown the physical reasons for the observed abnormal characteristics of some flap configurations. The results of calculations are presented in the form of pressure contours, pathlines, and force changes in the function of the angle of flap rotation. There is also presented estimated practical suitability of particular flap configurations for controlling the high-speed car stability and performance.
The paper describes the behavior of the liquid in a container that moves with a constant speed along a track consisting of three arcs. Such a complicated track shape generates complex form of inertia forces acting on the liquid and generates the sloshing effect. The behavior of the tank container vehicle is affected by the time-dependent inertia forces associated with the transient sloshing motion of the liquid in the non-inertial frame. These internal excitations, acting on a tank construction, can cause a loss of stability of the vehicle. For that reason, the authors analyze the dynamic loads acting on the walls of the tank truck container. The variation of the position of the liquid cargo gravity center, that depends on the filling level of the container, is also analyzed. The simulations were performed according to the varying fill level, which was 20%, 50% and 80% of a liquid in the whole tank volume. The simulations were carried out for a one-compartment container. Another aim of this study was the investigation of the influence of container division (tank with one, two and three compartments) on behavior of the liquid. These simulations considered only the half-filled container which was treated as a dangerous configuration prohibited by the law regulations for one-compartment tank. The results of simulation are presented in the form of visualization of temporary liquid free surface shape, variation of forces and moments, as well as frequency analysis. The results of simulation were analyzed, and some general conclusion were derived, providing the material for future investigation and modifications of the law regulations.
Recent investigations of micro engines have documented the problem of low efficiency of steady compression devices . As a solution, the application of unsteady processes has been proposed [1, 6, 17-20]. Closer investigations have shown the applicability of pure unsteady devices for gas compression, but it is also shown that they are practically not applicable for torque generation . A new concept of the wave engine has to be developed. This paper presents such a new concept and numerical investigation of the hybrid wave engine. A hybrid wave engine combines in a single machine components realizing unsteady compression, steady expansion, and mixed unsteady and steady scavenging due to the centrifugal force action. MEMS technology requires or prefers a flat geometry. Therefore, the use of a radial type of wave compression device for air compression is proposed. A numerical, two-dimensional complete model of this device was built, and several numerical simulations of engine operations were performed. The numerical model includes the simplified model of the combustion chamber closing the flow loop between the high-pressure compressed air port and the high-pressure hot exhaust gas port. The model represents the complete flow scheme of the hybrid wave engine. A special type of turbine in radial configuration with serial flow layout is used for torque generation.
Small-scale vertical-axis wind turbines can be used as a source of electricity in rural and urban environments. According to the authors’ knowledge, there are no validated simplified aerodynamic models of these wind turbines, therefore the use of more advanced techniques, such as for example the computational methods for fluid dynamics is justified. The paper contains performance analysis of the small-scale vertical-axis wind turbine with a large solidity. The averaged velocity field and the averaged static pressure distribution around the rotor have been also analyzed. All numerical results presented in this paper are obtained using the SST k-ω turbulence model. Computed power coefficients are in good agreement with the experimental results. A small change in the tip speed ratio significantly affects the velocity field. Obtained velocity fields can be further used as a base for simplified aerodynamic methods.