Power spectrum techniques were applied to two time series of wind speed values recorded at the Arctowski Station in order to investigate the influence of turbulent and laminar air flow on the quasi-periodicity of the micro-scale wind structure.
Obervations of wind directions and air temperatures in Hornsund, Spitsbergen, in 1978—1985 were used to compute frequency distribution of wind directions and mean air temperatures at particular wind directions. Prevailing easterly winds (60°, 90° and 120°) resulted in lower air temperatures (to —2.2°C) than winter and spring means and in higher (nearly 1°C) than summer and autumn mean temperatures. Greatest positive deviations from mean seasonal temperatures are observed in winter at southerly and southwesterly winds and reach 10°C. Greatest negative deviations from mean seasonal temperatures are noted at northerly winds (330° and 360°) in autumn and reach —3.7°C.
Observations from 1978—81, 1983 and 1985 collected at the Polish Polar Arctowski Station (King George Island, South Shetland Islands) were used to calculate frequencies of wind directions in 30° sectors and mean air temperatures observed at each wind direction. Results reveal that all over the year the warmest air masses flow onto the South Shetland Islands from the northwest while the coolest ones from the southeast and east.
The aim of the article is a preliminary assessment of the possibility of using ATES (Aquifer Thermal Energy Storage) technology for the seasonal storage of heat and cold in shallow aquifers in Poland. The ATES technology is designed to provide low-temperature heat and cold to big-area consumers. A study by researchers from the Delft University of Technology in the Netherlands indicates very favorable hydrogeological and climate conditions in most of Poland for its successful development. To confirm this, the authors used public hydrogeological data, including information obtained from 1324 boreholes of the groundwater observation and research network and 172 information sheets of groundwater bodies (GWBs). Using requirements for ATES systems, well-described in the world literature, the selection of boreholes was carried out in the GIS environment, which allowed aquifers that meet the required criteria to be captured. The preliminary assessment indicates the possibility of the successful implementation of ATES technology in Poland, in particular in the northern and western parts of the country, including the cities of: Gdańsk, Warsaw, Wrocław, Bydgoszcz, Słupsk, and Stargard.
The paper presents an approach of numerical modelling of alloy solidification in permanent mold and transient heat transport between the casting and the mold in two-dimensional space. The gap of time-dependent width called "air gap", filled with heat conducting gaseous medium is included in the model. The coefficient of thermal conductivity of the gas filling the space between the casting and the mold is small enough to introduce significant thermal resistance into the heat transport process. The mathematical model of heat transport is based on the partial differential equation of heat conduction written independently for the solidifying region and the mold. Appropriate solidification model based on the latent heat of solidification is also included in the mathematical description. These equations are supplemented by appropriate initial and boundary conditions. The formation process of air gap depends on the thermal deformations of the mold and the casting. The numerical model is based on the finite element method (FEM) with independent spatial discretization of interacting regions. It results in multi-mesh problem because the considered regions are disconnected.
The aim of the study was to compare anaesthesia protocol utilizing combination ketamine/ medetomidine with epidural lidocaine or morphine to orthopaedic surgery in rabbits. All rabbits received intramuscularly medetomidine (0.5 mg/kg) and ketamine (20 mg/kg). In group L (n=13) epidural injection was performed with lidocaine (3 mg/kg) and in group M (n=13) with morphine (0.1 mg/kg) diluted with sterile saline to 0.6 ml. Rabbits underwent bilateral mosaicplasty surgery. Heart rate (HR), systolic (SBP), diastolic (DBP) and mean arterial blood pressure (MAP), arte- rial oxygen saturation (SpO2) and respiratory rate (RR) were measured every 5 minute during surgical procedure. Duration of sensory blockade was measured based on toe pinch reflex and recorded. Hemodynamic parameters were comparable at baseline in both groups. We did not observe significant differences in HR, RR, SBP, DBP, MAP between group L and M. Intragroup statistical analysis revealed differences at different time points in group M in terms of HR, SBP, DBP, MAP. In rabbits in group M blood pressure dropped while HR increased over time. In both groups a decrease in SpO2 was observed. Mean duration of loss of the toe pinch reflex was similar between group L and M, and amounted to 72.79±34.48 and 82.80±17.85 minutes, respectively.
In this paper, the mathematical model and numerical simulations of the molten steel flow by the submerged entry nozzle and the filling process of the continuous casting mould cavity are presented. In the mathematical model, the temperature fields were obtained by solving the energy equation, while the velocity fields were calculated by solving the momentum equations and the continuity equation. These equations contain the turbulent viscosity which is found by solving two additional transport equations for the turbulent kinetic energy and its rate of dissipation. In the numerical simulations, coupling of the thermal and fluid flow phenomena by changes in the thermophysical parameters of alloy depending on the temperature has been taken into consideration. This problem (2D) was solved by using the finite element method. Numerical simulations of filling the continuous casting mould cavity were performed for two variants of liquid metal pouring. The effect of the cases of pouring the continuous casting mould on the velocity fields and the solid phase growth kinetics in the process of filling the continuous casting mould was evaluated as these magnitudes have an influence on the high quality of the continuous cast steel slab.
The main goal of this work is to show the new approach to determining safety technological levels (SLs) in terms of water quality and its chemical stability, as well as issues of water corrosion properties in water distribution systems (WDSs), due to the fact that water supply pipes are prone to corrosion. In the paper the methodology of determining the risk associated with threat to technical infrastructure was considered. The concept was studied on the basis of real operational data from the water treatment plant. The probability of exceeding the individual parameters for WTPI is slightly larger than for WTPII, which means that this water treatment process may cause lack of chemical stability in the water supply network. Operators should anticipate in the process of designing water distribution system, using proper materials, as to ensure an adequate level of safety from the water source to the water recipient. It should be noted that it is necessary to adjust the material of internal installation of water supply networks to the parameters of the water. At present, there are no correlations between the designing step and water parameters. It was concluded that to protect the water supply infrastructure, which belongs to critical infrastructure, water company should put more emphasis on distribution of stable water that has not potentially corrosion properties. Some suggestions were made for the protection of WDS and to ensure safety of system functioning and long-term usability of water pipes.