In order to study the effects of various gating systems on the casting of a complex aluminum alloyed multi-way valve body, both software simulation analysis and optimization were carried out. Following, the aluminum alloyed multi-way valve body was cast to check the pouring of the aluminum alloy valve body. The computer simulation results demonstrated that compared to the single side casting mode, the casting method of both sides of the gating system would reduce the filling of the external gas, while the air contact time would be lower. Adversely, due to the pouring on both sides, the melt cannot reach at the same time, leading to the liquid metal speed into the cavity to differ, which affected the liquid metal filling stability. The riser unreasonable setting led to the solidification time extension, resulting in a high amount of casting defects during solidification. Also, both gating systems led the entire casting inconsequential solidification. To overcome the latter problems, a straight gate was set at the middle pouring and the horizontal gate diversion occurred on both sides of pouring, which could provide better casting results for the aluminum alloyed multi-valve body.
Skeleton castings macrostructure can be shaped in many ways, by choosing an appropriate material of cores and manufacturing technologies. Important factor, which puts foundry techniques over the other technologies of periodic cellular materials, is ability to adjust mechanical properties by changing the microstructure of an alloy from which the casting is made. The influence on the microstructure of the skeleton casting can be implemented by choosing the thermal properties, mainly thermal conductivity factor, of mould and core materials. Macro- and microstructure of skeleton castings with octahedron elementary cells was presented in this paper. The analysis concerns the differences in morphology of eutectic silicone depending on the location of measurements cross sections areas. The use of thermo-insulating material with appropriate properties assures correct fill of mould cavity and homogeneous microstructure on whole volume of skeleton casting. The selection of technological parameters of the casting process if very important as well.
The friction and wear properties of 201HT aluminum alloys and the corresponding competitive coupons were tested on an electrohydraulic servo face friction and wear testing machine (MM-U10G). The microstructures of the competitive coupons were investigated by scanning electron microscopy (SEM) and consequently the corresponding friction and wear mechanisms were studied. The results demonstrated that: (1) the best competitive material of friction and wear performance of the 201HT was the 201HTC. (2) the 201HTC modified by carbon following the initial mill for oil storage of the micro-groove to be produced, increased the corresponding lubrication performance reduced the friction coefficient and wear rate effectively. (3) the 201HT-201HTC could obtain both better friction and wear mainly due to the initial process of grinding following the 201HT plastic deformation occurred in the surface and the formation of a series of re-melting welding points, whereas the 201HT material hardness would be similar to the 201HTC material hardness, which led into the competitive material friction and wear performance improvement.
The study involved using the liquid-solid compound casting process to fabricate a lightweight ZE41/AlSi12 bimetallic material. ZE41 melt heated to 660 oC was poured onto a solid AlSi12 insert placed in a steel mold. The mold with the insert inside was preheated to 300 oC. The microstructure of the bonding zone between the alloys was examined using optical microscopy and scanning electron microscopy. The chemical composition was determined through linear and point analyses with an energy-dispersive X-ray spectroscope (EDS). The bonding zone between the magnesium and aluminum alloys was about 250 μm thick. The results indicate that the microstructure of the bonding zone changes throughout its thickness. The structural constituents of the bonding zone are: a thin layer of a solid solution of Al and Zn in Mg and particles of Mg-Zn-RE intermetallic phases (adjacent to the ZE41 alloy), a eutectic region (Mg17(Al,Zn)12 intermetallic phase and a solid solution of Al and Zn in Mg), a thin region containing fine, white particles, probably Al-RE intermetallic phases, a region with Mg2Si particles distributed over the eutectic matrix, and a region with Mg2Si particles distributed over the Mg-Al intermetallic phases matrix (adjacent to the AlSi12 alloy). The microstructural analysis performed in the length direction reveals that, for the process parameters tested, the bonding zone forming between the alloys was continuous. Low porosity was observed locally near the ZE41 alloy. The shear strength of the AZ91/AlSi17 joint varied from 51.3 to 56.1 MPa.
The article presents the results of research concerning AlCu4MgSi alloy ingots produced using horizontal continuous casting process under variable conditions of casting speed and cooling liquid flow through the crystallizer. The mechanical properties and structure of the obtained ingots were correlated with the process parameters. On the basis of the obtained results, it has been shown that depending on the cooling rate and the intensity of convection during solidification, significant differences in the mechanical properties and structure and of the ingots can occur. The research has shown that, as the casting speed and the flow rate of the cooling liquid increase, the hardness of the test samples decreases, while their elongation increases, which is related to the increase of the average grain size. Also, the morphology of the intermetallic phases precipitations lattice, as well as the centerline porosity and dendrite expansion, significantly affect the tensile strength and fracture mechanism of the tested ingots.