Search results

Filters

  • Journals
  • Date

Search results

Number of results: 5
items per page: 25 50 75
Sort by:

Abstract

This paper presents a method for quantitative assessment of the mechanisms of nucleation and granules growth by layering in the process of bed wetting during periodic disc granulation. This study included two initial, consecutive stages of a process with defined time courses. The first phase was a time period, in which only formation of new nuclei took place, while in the second stage simultaneous nucleation and growth of granules as a result of sticking raw material grains to pre-existing nuclei occurred. Different kinds of binding liquid were used for bed wetting in each phase. In the first phase, an aqueous solution of dye was used, and pure distilled water in the second stage. The contribution of particular mechanisms to the formation of agglomerates at different time points within the second phase of the process was determined in this study. To do that the results of bed granulometric analysis, mass balance of size fractions and the analysis of contents of a marker (dye) delivered to the bed with the binding liquid during the first phase in agglomerates were used. To assess the concentration of the dye in different size fractions of the batch, spectrophotometric analysis was utilised. The study was performed using UV-VIS JASCO V-630 spectrophotometer equipped with an integrating sphere. The sieve analysis, spectrophotometric studies and mass balance were used to determine changes in the weight of the dye containing nuclei and of the nuclei containing no dye. The aforementioned analyses were also used to assess changes in the weight of formed granules and of raw material particles attached to nuclei during simultaneous nucleation and growth of granules.
Go to article

Abstract

Eutectoid growth, as the important reaction mechanism of the carbon steel heat treatment, is the basis to control the microstructure and performance. At present, most studies have focused on lamellar growth, and did not consider the nucleation process. Mainly due to the nucleation theory is inconclusive, a lot of research can support their own theory in a certain range. Based on the existing nucleation theory, this paper proposes a cooperative nucleation model to simulate the nucleation process of eutectoid growth. In order to ensure that the nucleation process is more suitable to the theoretical results, different correction methods were used to amend the model respectively. The results of numerical simulation show that when the model is unmodified, the lateral growth of single phase is faster than that of longitudinal growth, so the morphology is oval. Then, the effects of diffusion correction, mobility correction and ledges nucleation mechanism correction on the morphology of nucleation and the nucleation rate were studied respectively. It was found that the introduction of boundary diffusion and the nucleation mechanism of the ledges could lead to a more realistic pearlite.
Go to article

Abstract

Cast irons are good examples of materials which are more sensitive to chemical composition and production conditions. In this research to improve casting quality, solidification and nucleation process in grey cast iron was investigate. In particular, attempts have been made to rationalize variation in eutectic cells with nucleation sites and eutectic solidification undercooling. Four castings with different diameter and similar chemical composition and pouring temperature and different inoculant percentage was casted. The cooling curve and maximum and minimum undercooling for each castings was measured. Also optical metallography and image analyzer has been used to determine the average eutectic cells diameter, and linear and surface densities, and volume density was calculated. The results of this research show a competitive behavior between nucleation sites and eutectic undercooling. Higher nucleation sites and higher eutectic undercooling cause higher eutectic cell density. But increasing nucleation sites by introducing inoculants to molten metal, is accompanied with reduction in eutectic undercooling. It means that inoculation and undercooling have opposite effect on each other. So, to achieve maximum cell density, it is necessary to create an optimization between these parameters.
Go to article

Abstract

The orientations of recrystallization nuclei and their adjacent as-deformed regions have been characterised in deformed single crystals of different metals (Ag, Cu, Cu-2%wt.Al and Cu-8%wt.Al) in which twinning and/or shear banding occur. {112}<111> oriented crystals of these metals have been compressed to different strains, then lightly annealed, and the crystallographic aspects of the recrystallization process along shear bands examined by local orientation measurement in TEM and SEM. The results clearly show the existence of a well-defined crystallographic relation between the local deformation substructure and the first recrystallized areas of uniform orientation. The first-formed nuclei always exhibit near 25–400(<111>–<112>) type misorientations, in the direction of highest growth, with respect to one of the two main groups of the deformation texture components. The rotation axes can be correlated with the slip plane normal of highest activity. As recrystallization proceeds, recrystallization twinning develops strongly and facilitates rapid growth; the first and higher generations of twins then tend to obscure the initial primary crystallographic relation between the shear bands and recrystallization nuclei .
Go to article

Abstract

Reduction of three industrial nickel oxides (Goro, Tokyo and Sinter 75) with a hydrogen bearing gas was revisited in the temperature interval from 523 to 673 K (250 to 400°C). A pronounced incubation period is observed in the temperature interval tested. This period decreases as the reduction temperature increases. Thermogravimetric data of these oxides were fitted using the Avrami-Erofeyev kinetic model. The reduction of these oxides is controlled by a nucleation and growth mechanism of metallic nickel over the oxides structure. Rate kinetic constants were re-evaluated and the activation energy for the reduction of these oxides was re-calculated.
Go to article

This page uses 'cookies'. Learn more