Ablation casting is a technological process in which the increased cooling rate causes microstructure refinement, resulting in improved mechanical properties of the final product. This technology is particularly suitable for the manufacture of castings with intricate shapes and thin walls. Currently, the ablation casting process is not used in the Polish industry. This article presents the results of strength tests carried out on moulding sands based on hydrated sodium silicate hardened in the Floster S technology, intended for ablation casting of the AlSi7Mg (AK7) aluminium alloy. When testing the bending and tensile strengths of sands, parameters such as binder and hardener content were taken into account. The sand mixtures were tested after 24h hardening at room temperature. The next stage of the study describes the course of the ablation casting process, starting with the manufacture of foundry mould from the selected moulding mixture and ending in tests carried out on the ready casting to check the surface quality, structure and mechanical properties. The results were compared with the parallel results obtained on a casting gravity poured into the sand mould and solidifying in a traditional way at ambient temperature.
Changes of gas pressure in the moulding sand in the zone adjacent to mould cavity were analysed during pouring of cast iron. No significant effect of pressure on the surface quality of castings was observed. In the second series of tests, the concentration of hydrogen in the gas atmosphere was measured. It has been found that the value of this concentration depends on metal composition and is particularly high in cast iron containing magnesium. This is due to the reduction of water vapour with the element that has high affinity to oxygen. The presence of hydrogen causes the formation of gas-induced defects on the casting surface.
The paper presents the technology and organization of the artistic cast production. On the basis of the actual cast production system, the manufacturing process was shown, in particular sand–piece moulding, which is a very important process and a time-consuming part of the entire manufacture of the casts. The current state of the production process as well as the organization of the work and production technology were analysed with the use of methods and techniques of production improvement, the Lean Manufacturing concept and computer systems. The results of the analysis and studies were shown with use of schemes and graphs of the layout of the production resources, a flow chart of the production process, value stream mapping, and a costs table for the production and modernization of the moulding stage. The work has shown that there are possibilities to improve the artistic cast production system. This improvement leads to increased productivity, lower production costs of artistic casts and increased competitiveness of the foundry.
Skeleton castings macrostructure can be shaped in many ways, by choosing an appropriate material of cores and manufacturing technologies. Important factor, which puts foundry techniques over the other technologies of periodic cellular materials, is ability to adjust mechanical properties by changing the microstructure of an alloy from which the casting is made. The influence on the microstructure of the skeleton casting can be implemented by choosing the thermal properties, mainly thermal conductivity factor, of mould and core materials. Macro- and microstructure of skeleton castings with octahedron elementary cells was presented in this paper. The analysis concerns the differences in morphology of eutectic silicone depending on the location of measurements cross sections areas. The use of thermo-insulating material with appropriate properties assures correct fill of mould cavity and homogeneous microstructure on whole volume of skeleton casting. The selection of technological parameters of the casting process if very important as well.
In this paper, the authors investigated the size distribution of titanium oxide (TiO2), titanium nitride (TiN) and titanium carbide (TiC) inclusions in a titanium deoxidized 4130 steel and compared it with the 4130 base alloy composition inclusions. TiN and TiC inclusions are of particular interest due to their role as heterogeneous nuclei for various phase reactions in steels. Two types of samples were prepared, a polished sample and a filtered sample. Electrolytic dissolution was employed to make the filter paper samples. The size range of titanium inclusions was found to be more than that of the non-metallic inclusions from 4130 base alloy heat. Titanium inclusions from the filter and polished samples were round in shape. TiC and TiN inclusions were not found in the electrolytic extraction samples. Inclusions and their chemistries were analyzed using scanning electron microscope and energy dispersive spectrometer. The inclusion size range was larger for the titanium deoxidized samples than the base alloy. However, in both steels the majority of inclusions had a size smaller than 10 μm.
Gas atmosphere at the sand mould/cast alloy interface determines the quality of the casting obtained. Therefore the aim of this study was to measure and evaluate the gas forming tendency of selected moulding sands with alkyd resins. During direct and indirect gas measurements, the kinetics of gas evolution was recorded as a function of the temperature of the sand mixture undergoing the process of thermal destruction. The content of hydrogen and oxygen was continuously monitored to establish the type of the atmosphere created by the evolved gases (oxidizing/reducing). The existing research methodology [1, 7, 8] has been extended to include pressure-assisted technique of indirect measurement of the gas evolution rate. For this part of the studies, a new concept of the measurement was designed and tested. This article presents the results of measurements and compares gas emissions from two sand mixtures containing alkyd resins known under the trade name SL and SL2002, in which the polymerization process is initiated with isocyanate. Studies of the gas forming tendency were carried out by three methods on three test stands to record the gas evolution kinetics and evaluate the risk of gas formation in a moulding or core sand. Proprietary methods for indirect evaluation of the gas forming tendency have demonstrated a number of beneficial aspects, mainly due to the ability to record the quantity and composition of the evolved gases in real time and under stable and reproducible measurement conditions. Direct measurement of gas evolution rate from the tested sands during cast iron pouring process enables a comparison of the results with the results obtained by indirect methods.
This work presents a scheme for the manufacture of spherical grinding bodies used in grinding and crushing machinery as a grinding medium from abrasion-resistant cast iron CHKH16 (according to GOST 7769-82) free of shrinkage defects produced by casting into single sand molds with a vertical joint and by usingcoolers. The grinding efficiency in terms of material destruction and energy consumption has been studied according to a wide range of operating parameters and new scheme for calculating the sprue and supply system has been developed by the authors of the article. Its functionality has been substantiated, particularly the use of a central riser acting as a head and the use of coolers. The conducted numerical simulation has shown the dependence of a solid phase formation over time, which characterizes the direction of the system crystallization and determines the locations of the shrinkage defects concentration. The manufacture of the grinding body with a 100 mm diameter using the considered technology is presented in this paper.
The paper presents results of measuring attenuation coefficient of the Al-20 wt.% Zn alloy (AlZn20) inoculated with different grain refiners. During experiments the melted alloys were doped with Al-Ti3-C0.15 refining master alloy. Basing on measurements performed by Krautkramer USLT2000 device with 1MHz ultrasound wave frequency it was stated that grain refinement reduces the attenuation coefficient by about 20-25%. However, the examined alloys can be still classified as the high-damping ones of attenuation greater than 150 dB/m.
In sand casting, Fused Deposition Modeling (FDM) printing by using Poly Lactic Acid (PLA) filament is one of the innovative foundry technologies being adopted to substitute traditional pattern making. Several literatures have reported the influence of process parameters such as raster angle and print speed on some mechanical properties of FDM-printed, PLA-prototypes used in other applications. This study investigated the effects of interior fill, top solid layer, and layer height on the compressive strength of rapid patterns for sand casting application. Different values of the process parameters were used to print the pre-defined samples of the PLA-specimens and a compression test was performed on them. The coupled effects of the process parameters on compressive strength were investigated and the optimum values were determined. Interior fill of 36%, layer height of 0.21 mm and top solid layer of 4 were found to produce a FDM-printed, PLApattern that sustained a compaction pressure of 0.61 MPa. A simulation analysis with ANSYS® to compare failure modes of both experiment and model shows a similarity of buckling failure that occurred close to the base of each specimen.
The essence of ablation casting technology consists in pouring castings in single-use moulds made from the mixture of sand and a watersoluble binder. After pouring the mould with liquid metal, while the casting is still solidifying, the mould destruction (washing out, erosion) takes place using a stream of cooling medium, which in this case is water. This paper focuses on the selection of moulding sands with hydrated sodium silicate for moulds used in the ablation casting. The research is based on the use of Cordis binder produced by the Hüttenes-Albertus Company. It is a new-generation inorganic binder based on hydrated sodium silicate. Its hardening takes place under the effect of high temperature. As part of the research, loose moulding mixtures based on the silica sand with different content of Cordis binder and special Anorgit additive were prepared. The reference material was sand mixture without the additive. The review of literature data and the results of own studies have shown that moulding sand with hydrated sodium silicate hardened by dehydration is characterized by sufficient strength properties to be used in the ablation casting process. Additionally, at the Foundry Research Institute in Krakow, preliminary semi-industrial tests were carried out on the use of Cordis sand technology in the manufacture of moulds for ablation casting. The possibility to use these sand mixtures has been confirmed in terms of both casting surface quality and sand reclamation.