The protection of Polish architectural heritage in the former eastern borderlands, accomplished through the conservation and technical securing of historical structures, constitutes one of the main programmes that are implemented by the Ministry of Culture and National Heritage. Currently, many Polish historical buildings in the former eastern borderlands are in a very bad technical condition. The load-bearing systems of these elements, as well as elements of their finish, require immediate emergency securing work. The basic steps that precede conservation work are emergency structural works, which guarantee the durability and stability of the entire historical substance. The specifics and complexity of the problem of the failure of historical buildings often demands an in-depth analysis of a series of factors that are difficult to measure and which are responsible for the cause and effect relationship during the early stage of the technical evaluation of a structure. The analyses of failures of numerous historical structures, for instance that were carried out by the authors, have become the inspiration for the search for effective methods of analysis that would allow for an in-depth analysis of the causes and effects of the failures in question. The DEMATEL method (Decision Making Trial and Evaluation Laboratory) that has been presented in this work, and its fuzzy extension, has lately become one of the more popular methods used in the cause-and-effect analysis of various phenomena. The authors demonstrated how this method works on the example of the evaluation and securing of the load-bearing system of the XVII Collegiate church of the Holy Trinity in the town of Olykha in the Volhynskiy Oblast, Ukraine.
The article is focused on the most recent investigations of glaciotectonic structures in high escarpment exposures of the Vistula valley from Dobrzyń to Kuzki in the western part of the Płock Basin. Deformations involve Neogene and occasionally the Lower Pleistocene deposits and they are not expressed as landforms. Structural investigations and analysis of archival geological data provided new information on the origin of large-scale shear structures. Results obtained are clearly contrary to the concept of Brykczyński (1982) regarding valley-side glaciotectonics in the Płock Basin. An emergence of the extensive zone of serial thrust structures of significant amplitude (up to 100–150 m) was found to have not been controlled by a palaeovalley. A driving mechanism is interpreted as a gravity spreading in front of ice sheets advancing from north-northeast during the South Polish Complex (Dorst-Elsterian).
The Carpathian Orava Basin is a tectonic structure filled with Neogene and Quaternary deposits superimposed on the collision zone between the ALCAPA and European plates. Tectonic features of the south-eastern margin of the Orava Basin and the adjoining part of the fore-arc Central Carpathian Palaeogene Basin were studied. Field observations of mesoscopic structures, analyses of digital elevation models and geological maps, supplemented with electrical resistivity tomography surveys were performed. Particular attention was paid to joint network analysis. The NE-SW-trending Krowiarki and Hruštinka-Biela Orava sinistral fault zones were recognized as key tectonic features that influenced the Orava Basin development. They constitute the north-eastern part of a larger Mur-Mürz-Žilina fault system that separates the Western Carpathians from the Eastern Alps. The interaction of these sinistral fault zones with the older tectonic structures of the collision zone caused the initiation and further development of the Orava Basin as a strike-slip-related basin. The Krowiarki Fault Zone subdivides areas with a different deformation pattern within the sediments of the Central Carpathian Palaeogene Basin and was active at least from the time of cessation of its sedimentation in the early Miocene. Comparison of structural data with the recent tectonic stress field, earthquake focal mechanisms and GPS measurements allows us to conclude that the Krowiarki Fault Zone shows a stable general pattern of tectonic activity for more than the last 20 myr and is presently still active.
This article combines a general introduction to the crime fi ction of Walery Przyborowski with a study of the structure of the plot of his novels. The analyses of ten of his novels conclude with a typology of their narrative schemes, shown in the context of certain invariant patterns and the conventions of related literary genres. While the main objective of this study is to outline the structure of crime story and the social issues depicted in Przyborowski’s crime fi ction, it also pays some attention to the ways in which it refl ects his concerns about contemporary life and the condition of Poland under foreign rule. Basically, Przyborowski’s formula is to make use of the staples of the genre – mystery, adventure, romance – and the techniques of the popular novel. Moreover, his novels, like all of the 19th-century crime fi ctions, are clearly indebted to the conventions of the historical novel.
The paper discusses possible applications of the percolation theory in analysis of the microstructure images of polycrystalline materials. Until now, practical use of this theory in metallographic studies has been an almost unprecedented practice. Observation of structures so intricate with the help of this tool is far from the current field of its application. Due to the complexity of the problem itself, modern computer programmes related with the image processing and analysis have been used. To enable practical implementation of the task previously established, an original software has been created. Based on cluster analysis, it is used for the determination of percolation phenomena in the examined materials. For comparative testing, two two-phase materials composed of phases of the same type (ADI matrix and duplex stainless steel) were chosen. Both materials have an austenitic - ferritic structure. The result of metallographic image analysis using a proprietary PERKOLACJA.EXE computer programme was the determination of the content of individual phases within the examined area and of the number of clusters formed by these phases. The outcome of the study is statistical information, which explains and helps in better understanding of the planar images and real spatial arrangement of the examined material structure. The results obtained are expected to assist future determination of the effect that the internal structure of two-phase materials may have on a relationship between the spatial structure and mechanical properties.
The article presents results of research on the influence of variable parameters of horizontal continuous casting on the structure of AlCu4MgSi (EN AW-2017A) alloy ingots. The special character of the process allows for a continuous change of some of its parameters, namely, of the casting speed and of the rate of the cooling fluid flow thorough the crystallizer. These parameters have a significant impact on the crystallization process of the liquid metal. Depending on the cooling rate, intensity of the convection inside the solidifying alloy, and its chemical composition, there may arise some differences in the structure of the cast. In this study, ingots obtained at different casting speeds have been analyzed. The research methodology, based on light microscopy and electron microscopy (SEM), as well as energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD), allowed for a thorough examination of the structure of the studied materials. The results were shown that an increase in the ingot casting speed leads to an increase in the average grain surface area.
The task of generating fast and accurate three-dimensional (3D) models of objects or scenes through a sequence of non-calibrated images is an active field of research. The recent development in algorithm optimization has resulted in many automatic solutions that can provide an accurate 3D model from texture-full objects. Structure-from-motion (SfM) is an image-based method that uses discriminative point-based feature identifier, such as SIFT, to locate feature points in the images. This method faces difficulties when presented with the objects made of homogenous or texture-less surfaces. To reconstruct such surfaces a well-known technique is to apply an artificial variety by covering the surface with a random texture pattern prior to the image capturing process. In this work, we designed three series of image patterns which are tested based on the contrast and density ratio which increases from the first to the last pattern within the same series. The performance of the patterns is evaluated by reconstructing the surface of a texture-less object and comparing it with the true data. Using the best-found patterns from the experiments, a 3D model of a Moai statue is reconstructed. The experimental results demonstrate that the density and structure of a pattern highly affects the quality of the reconstruction.
In order to optimize the stope structure parameters in broken rock conditions, a novel method for the optimization of stope structure parameters is described. The method is based on the field investigation, laboratory tests and numerical simulation. The grey relational analysis (GRA) is applied to the optimization of the stope structure parameters in broken rock conditions with multiple performance characteristics. The influencing factors include stope height, pillar diameter, pillar spacing and pillar array pitch, the performance characteristics include maximum tensile strength, maximum compressive strength and ore recovery rate. The setting of influencing factors is accomplished using the four factors four levels Taguchi experiment design method, and 16 experiments are done by numerical simulation. Analysis of the grey relational grade indicates the first effect value of 0.219 is the pillar array pitch. In addition, the optimal stope structure parameters are as follows: the height of the stope is 3.5 m, the pillar diameter is 3.5 m, the pillar spacing is 3 m and the pillar array pitch is 5 m. In-situ measurement shows that all of the pillars can basically remain stable, ore recovery rate can be ensured to be more than 82%. This study indicates that the GRA method can efficiently applied to the optimization of stope structure parameters.
The paper describes the influence of the machining operation on a surface, which disturbs the projection of the tool profile in the form of its relative movements with respect to the object. The elements of the machine tool undergo constant wear during the machining process, it is therefore important to recognize the effects of their influence on the surface's irregularities. Amplitude-frequency analysis of lateral profiles has been used to evaluate and changes of turned lateral profiles. The results of simulation of radial and axial effects of the machine tool on surface and their spectral components were analyzed. Surfaces obtained in similar machining conditions on lathes operated in various time periods were analyzed spectrally. From the analysis of surface irregularity changes caused by disturbances in movements of the tool against the object, testifying the wear of main machine elements during its operation, the modulated, amplitude-frequency character of changes in surface irregularities of workpiece can be noticed.
Modern production technology requires new ways of surface examination and a special kind of surface profile parameters. Industrial quality inspection needs to be fast, reliable and inexpensive. In this paper it is shown how stochastic surface examination and its proper parameters could be a solution for many industrial problems not necessarily related with smoothing out a manufactured surface. Burnishing is a modern technology widely used in aircraft and automotive industries to the products as well as to process tools. It gives to the machined surface high smoothness, and good fatigue and wear resistance. Every burnished material behaves in a different manner. Process conditions strongly influence the final properties of any specific product. Optimum burnishing conditions should be preserved for any manufactured product. In this paper we deal with samples made of conventional tool steel – Sverker 21 (X153CrMoV12) and powder metallurgy (P/M) tool steel – Vanadis 6. Complete investigations of product properties are impossible to perform (because of constraints related to their cost, time, or lack of suitable equipment). Looking for a global, all-embracing quality indicator it was found that the correlation function and the frequency analysis of burnished surface give useful information for controlling the manufacturing process and evaluating the product quality. We propose three new indicators of burnishing surface quality. Their properties and usefulness are verified with the laboratory measurement of material samples made of the two mentioned kinds of tool steel.