Four Geodynamical Expeditions of the Polish Academy of Sciences carried through wide research seismic program in West Antarctica in 1979-1991. Three of these expeditions operated in the Bransfield Strait. The experiment of deep refraction and wide-angle reflection in West Antarctica focused on deep structure of the lithosphere, mainly of the Earth's crust. The network of deep seismic soundings (DSS) profiles covered all the Bransfield Strait. Five land stations on the South Shetland Islands, three stations on the Antarctic Peninsula and nine ocean bottom seismographs (OBS) recorded seismic waves, generated by explosions in a sea. The Bransfield Rift and the Bransfield Platform form a marginal basin against a volcanic arc of the South Shetland Islands. The paper presents new results of 2-D seismic modeling for network of five selected profiles. Four of them, ranging in lenght from 150 to 190 km, crossed main structures of the Bransfield Strait and the fifth, which connected the other ones and was 310 km long, ran along the Bransfield Rift. Two or three seismic models were presented for each profile. Finally, mutually corrected and controlled 2-D models of described profiles were constructed. They all presented spatial complex structure of the Earth's crust in a young rift of the Bransfield Strait, including extent of its main element i.e. anomalous high velocity body (HVB) (Vp > 7.4 km/s), detected in 10-30 km depth range except profile DSS-4 (southwest part of the Bransfield Strait). This inhomogeneity is interpreted as intrusion of the upper mantle (?asthenosphere) during stretching of the continental crust. The Moho discontinuity was found at depth 30-35 km, with velocities equal to about 8.1 km/s.
The paper presents a new numerical model of solidification processes in hypoeutectic alloys. The model combines stochastic elements, such as e.g. random nucleation sites and orientation of dendritic grains, as well as deterministic methods e.g. to compute velocity of dendritic tips and eutectic grains. The model can be used to determine the temperature and the size of structure constituents (of both, the primary solid phase and eutectics) and the arrangement of individual dendritic and eutectic grains in the consecutive stages of solidification. Two eutectic transformation modes, typical to modified and unmodified hypoeutectic alloys, have been included in the model. To achieve this, cellular automata and Voronoi diagrams have been utilized.
In Part I of this article, two-stage solidification model was presented. In this part we use our model to simulate solidification of the Al 7% Si alloy for two cooling rates and . Simulations have been performed for two eutectic transformation modes, typical for modified and unmodified alloys. Obtained cooling curves are qualitatively consistent with the typical cooling curves for modified and unmodified alloys. Moreover, evolution of cooling-curve characteristics is compared with the analytical model and found to be in close agreement.
Rock excavation is a basic technological operation during tunnelling and drilling roadways in underground mines. Tunnels and roadways in underground mines are driven into a rock mass, which in the particular case of sedimentary rocks, often have a layered structure and complicated tectonics. For this reason, rock strata often have highly differentiated mechanical properties, diverse deposition patterns and varied thicknesses in the cross sections of such headings. In the field of roadheader technology applied to drilling headings, the structure of a rock mass is highly relevant when selecting the appropriate cutting method for the heading face. Decidedly differentiated values of the parameters which describe the mechanical properties of a particular rock layer deposited in the cross section of the drilled tunnel heading will influence the value and character of the load on the cutting system, generated by the cutting process, power demand, efficiency and energy consumption of the cutting process. The article presents a mathematical modelling process for cutting a layered structure rock mass with the transverse head of a boom-type roadheader. The assumption was made that the rock mass being cut consists of a certain number of rock layers with predefined mechanical properties, a specific thickness and deposition pattern. The mathematical model created was executed through a computer programme. It was used for analysing the impact deposition patterns of rock layers with varied mechanical properties, have on the amount of cutting power consumed and load placed on a roadheader cutting system. The article presents an example of the results attained from computer simulations. They indicate that variations in the properties of the rock cut – as cutting heads are moving along the surface of the heading face – may have, apart from multiple other factors, a significant impact on the value of the power consumed by the cutting process.
The paper presents the cellular automaton (CA) model for tracking the development of dendritic structure in non-equilibrium solidification conditions of binary alloy. Thermal, diffusion and surface phenomena have been included in the mathematical description of solidification. The methodology for calculating growth velocity of the liquid-solid interface based on solute balance, considering the distribution of the alloy component in the neighborhood of moving interface has been proposed. The influence of solidification front curvature on the equilibrium temperature was determined by applying the Gibbs Thomson approach. Solute and heat transfer equations were solved using the finite difference method assuming periodic boundary conditions and Newton cooling boundary condition at the edges of the system. The solutal field in the calculation domain was obtained separately for solid and liquid phase. Numerical simulations were carried out for the Al-4 wt.% Cu alloy at two cooling rates 15 K/s and 50 K/s. Microstructure images generated on the basis of calculations were compared with actual structures of castings. It was found that the results of the calculations are agreement in qualitative terms with the results of experimental research. The developed model can reproduce many morphological features of the dendritic structure and in particular: generating dendritic front and primary arms, creating, extension and coarsening of secondary branches, interface inhibition, branch fusion, considering the coupled motion and growth interaction of crystals.
A numerical model of binary alloy crystallization, based on the cellular automaton technique, is presented. The model allows to follow the crystallization front movement and to generate the images of evolution of the dendritic structures during the solidification of a binary alloy. The mathematic description of the model takes into account the proceeding thermal, diffusive, and surface phenomena. There are presented the results of numerical simulations concerning the multi-dendritic growth of solid phase along with the accompanying changes in the alloying element concentration field during the solidification of Al + 5% wt. Mg alloy. The model structure of the solidified casting was achieved and compared with the actual structure of a die casting. The dendrite interaction was studied with respect to its influence on the generation and growth of the primary and secondary dendrite arms and on the evolution of solute segregation both in the liquid and in the solid state during the crystallization of the examined alloy. The morphology of a single, free-growing dendritic crystal was also modelled. The performed investigations and analyses allowed to state e.g. that the developed numerical model correctly describes the actual evolution of the dendritic structure under the non-equilibrium conditions and provides for obtaining the qualitatively correct results of simulation of the crystallization process.
An innovative method for determining the structural zones in the large static steel ingots has been described. It is based on the mathematical interpretation of some functions obtained due to simulation of temperature field and thermal gradient field for solidifying massive ingot. The method is associated with the extrema of an analyzed function and with its points of inflection. Particularly, the CET transformation is predicted as a time-consuming transition from the columnar- into equiaxed structure. The equations dealing with heat transfer balance for the continuous casting are presented and used for the simulation of temperature field in the solidifying virtual static brass ingot. The developed method for the prediction of structural zones formation is applied to determine these zones in the solidifying brass static ingot. Some differences / similarities between structure formation during solidification of the steel static ingot and virtual brass static ingot are studied. The developed method allows to predict the following structural zones: fine columnar grains zone, (FC), columnar grains zone, (C), equiaxed grains zone, (E). The FCCT-transformation and CET-transformation are forecast as sharp transitions of the analyzed structures. Similarities between steel static ingot morphology and that predicted for the virtual brass static ingot are described.