Search results

Filters

  • Journals
  • Keywords
  • Date

Search results

Number of results: 7
items per page: 25 50 75
Sort by:

Abstract

It is estimated that the amount of used car tires in the European Union in 2016 was established at the level of 3,515,000 Mg, which is undoubtedly a problem from the point of view of engineering and environmental protection. An alternative to storing this waste in landfills is their pyrolysis. As a result of thermal decomposition, calorific value products (oil and gas fraction) are obtained, as well as a solid residue, which due to its composition and properties can be processed into a high quality carbon sorbent. For this purpose, various methods of modification of the pyrolyzate are used, both involving physical and chemical activation. This article presents the characteristics of solid residue after the pyrolysis of rubber tires running at a temperature of about 400°C, which included an analysis of chemical composition (XRF and IR), mineralogical composition (XRD, SEM-EDS) and textural characteristics. Additionally, for the purpose of activation, the sample was treated with nitrogen at a temperature of 550°C. The mineralogical analysis showed that the dominant mineral component is carbon. In addition, the presence of quartz, calcite and sphalerite was observed. Analysis of the chemical composition suggests that due to the high carbon content (about 80% by mass) it is possible for a carbon sorbent from the analyzed waste to be obtained. However, previous preliminary studies did not allow a material constituting a substitute for activated carbon to be obtained, because the applied modification only slightly increased the BET specific surface area, which reached the value of approx. 85 m2/g. Based on the analysis of the pore size distribution of the 2 tested samples, it was found to be homogeneous/modal with a micro/mesoporous nature, while the shape of the hysteresis loop suggests the presence of “bottle shape” pores. Due to the relatively high content of zinc, the composition of waste (about 4% of mass), the possibility of recovery of this element should also be considered.
Go to article

Abstract

This study examines the pyrolysis of a single cylindrical wood particle using particle image velocimetry (PIV). The pyrolysis was conducted inside a pyrolysis reactor designed for this purpose. The experimental setup presented in this paper is capable of effectively characterizing the intensity of pyrolysis based on velocity distribution in the vicinity of wood particles. The results of the gas velocity distribution show that evaporation of moisture has as a major impact on the formation of the gas cushion as devolatilization.
Go to article

Abstract

Anaerobic digestion residue represents a nutrient rich resource which, if applied back on land, can reduce the use of mineral fertilizers and improve soil fertility. However, dewatering and further thermal processing of digestate may be recommended in certain situations. Limited applicability of digestate as fertilizer may appear, especially in winter, during the vegetation period or in areas where advanced eutrophication of arable land and water bodies is developing. The use of digestate may be also governed by different laws depending on whether it is treated as fertilizer, sewage sludge or waste. The aim of this paper is to present the effects of thermal treatment of solid fraction of digestate by drying followed by pyrolysis and gasification. Pyrolysis was carried out at the temperature of about 500°C. During this process the composition of flammable gases was checked and their calorific value was assessed. Then, a comparative analysis of energy parameters of the digestate and the carbonizate was performed. Gasification of digestate was carried out at the temperature of about 850°C with use of CO2 as the gasifi cation agent. Gasification produced gas with higher calorific value than pyrolysis, but carbonizate from pyrolysis had good properties to be used as a solid fuel
Go to article

Abstract

Sand samples with furan binder were prepared using Sand, Furfuryl Alcohol and Toluene Sulfonic Acid with ratio 100:0.85:0.30. To identify and quantify gases releasing from furan binder various studies like FTIR, TGA and GC-MS were carried out. After analyzing our materials using above mentioned characterizations the chemical formula of the Resin and Binder and amount of gases releasing from composition were confirmed. After studying various reports on pyrolysis process of furan binder calculation of the % of various gases emitting during pyrolysis process of furan was carried out. Sample of gas collected from mold was analyzed using GC-MS. Based on GCMS measurement various gases emitting from furan sand mold were identified and their amount were calculate and compared with the international standers of permissible gas emission limits in a foundry. The purpose of this paper is to assist foundries in pollution prevention by devising clean technologies which maintain or improve the quality of ambient surrounding. This paper aimed at minimization of pollution of air by using various techniques.
Go to article

Abstract

Activation of tyre pyrolysis char (TPC) can significantly increase its market value. To date, it has been frequently carried out in different reactors. In this work, thermogravimetric analysis was used instead. The performance of activated pyrolysis chars was tested by adsorption of acetone vapour and comparison of the equilibrium adsorption capacities for all samples. The highest equilibrium adsorption capacity was observed for the carbon burn-off of #24; 60%. In addition, the equilibrium adsorption capacity of activated TPC decreases by about 10% after eleven adsorption/desorption cycles. Moreover, activation changed the porous structure of pyrolysis chars from mesoporous to micro-mesoporous.
Go to article

Abstract

In the foundry industry, many harmful compounds can be found, which as a result of gradual but long-term exposure to employees bring negative results. One of such compounds is phenol (aromatic organic compound), which its vapours are corrosive to the eyes, the skin, and the respiratory tract. Exposition to this compound also may cause harmful effects on the central nervous system and heart, resulting in dysrhythmia, seizures, and coma. Phenol is a component of many foundry resins, especially used in shell moulds in the form of resincoated sands. In order to identify it, the pyrolysis gas chromatography-mass spectrometry method (Py-GC/MS) was used. The tests were carried out in conditions close to real (shell mould process – temperature 300°C). During the measurement, attention was focused on the appropriate selection of chromatographic analysis conditions in order to best separate the compounds, as it is difficult to separate the phenol and its derivatives. The identification of compounds was based on own standards.
Go to article

Abstract

Pyrolysis is potentially an effective treatment of oily sludge for oil recovery, and the addition of a catalyst is expected to affect its pyrolysis behavior. In the present study, Fe/Al-pillared bentonite with various Fe/Al ratios as pyrolysis catalyst is prepared and characterized by XRD, N2 adsorption, and NH3-TPD. The integration of Al and Fe in the bentonite interlayers to form pillared clay is evidenced by increase in the basal spacing. As a result, a critical ratio of Fe/Al exists in the Fe/Al-pillared bentonite catalytic pyrolysis for oil recovery from the sludge. The oil yield increases with respect to increase in Fe/Al ratio of catalysts, then decreases with further increasing of Fe/Al ratio. The optimum oil yield using 2.0 wt% of Fe/Al 0.5-pillared bentonite as catalyst attains to 52.46% compared to 29.23% without catalyst addition in the present study. In addition, the addition of Fe/Al-pillared bentonite catalyst also improves the quality of pyrolysis-produced oil and promotes the formation of CH4. Fe/Al-pillared bentonite provides acid center in the inner surface, which is beneficial to the cracking reaction of oil molecules in pyrolysis process. The present work implies that Fe/Al-pillared bentonite as addictive holds great potential in industrial pyrolysis of oily sludge.
Go to article

This page uses 'cookies'. Learn more