Search results

Filters

  • Journals
  • Keywords
  • Date

Search results

Number of results: 5
items per page: 25 50 75
Sort by:

Abstract

Statistical conformity criteria for the compressive strength of concrete are a matter of debate. The criteria can have prejudicial effects on construction quality and reliability. Hence, the usefulness of statistical criteria for the small sample size n = 3 is questioned. These defects can cause a reduction in the quality of produced concrete and, consequently, too much risk for the recipient (investor). For this reason, the influence of conformity control on the value of the reliability index of concrete and reinforced concrete has been determined. The authors limited their consideration to the recommended standards PN-EN 206-1, PN-EN 1992 and ISO 2394 method of reliability index, which belongs to the analytical methods FORM (First Order Reliability Method). It assumes that the random variables are defined by two parameters of the normal distribution or an equivalent normal: the mean and the standard deviation. The impact of conformity control for n = 3 for concrete structures, designed according to the Eurocode 1992, for which the compressive strength of concrete is the capacity dominant parameter (sensitivity factor of dominating resistance parameter according to the FORM is 0.8), has been determined by evaluation of the reliability index.
Go to article

Abstract

The purpose of this work is to distinguish between Acoustic Emission (AE) signals coming from mechanical friction and AE signals coming from concrete cracking, recorded during fourteen seismic simulations conducted with the shaking table of the University of Granada on a reinforced concrete slab supported on four steel columns. To this end, a particular criterion is established based on the Root Mean Square of the AE waveforms calculated in two different temporal windows. This criterion includes a parameter calculated by optimizing the correlation between the mechanical energy dissipated by the specimen (calculated by means of measurements with accelerometers and displacement transducers) and the energy obtained from the AE signals recorded by low-frequency piezoelectric sensors located on the specimen. The final goal of this project, initiated four years ago, is to provide a reliable evaluation of the level of damage of Reinforced Concrete specimens by means of AE signals to be used in future Structural Health Monitoring strategies involving RC structures.
Go to article

Abstract

This paper presents the possibility to apply numerical simulation in static analysis of reinforcedconcrete structure strengthened with carbon fibre reinforced polymer composite strips (CFRP).Reinforced concrete beams, with strengthening in form values CFRP made of carbon fibres andepoxy resin, featuring various width, as well as non-strengthened bent beams, were analysed. Thesimply supported beams arranged in a free support scheme were subjected to two concentratedforces within full range of loading (until collapse). The numerical analysis was performed throughapplication of the Finite Elements Method (FEM), and the calculation model applied took intoaccount the geometric and physical nonlinearity. The problem was solved by application of thequasi-staticstrategy method of calculations using ABAQUS software. While analysing the results,we focused on the run of changes in structure displacement and development of material damage,up to the point of destruction of the beam.
Go to article

Abstract

Reinforced concrete composite slab consists of a thin prefabricated slab in which span reinforcement is located and of concrete joined with the slab, with such concrete being laid on site. The existence of a joint of two concretes in such floors is interpreted as introducing a contact layer into a monolithic slab. In the paper parameters of two models are estimated. The first is a model of a contact layer and the second is a model of a composite slab with a single degree of freedom. The models consider that the contact has elastic properties and inelastic properties causing energy dissipation. Experimental investigations are discussed further based on which the parameters values of the contact layer model were determined. Delamination was experienced for the slabs characterised by low contact layer stiffness after applying a maximum load. In addition, the strains of a contact layer having low stiffness are accompanied by lower energy dissipation than of a layer with high stiffness. The smaller stiffness of composite floors, as compared to monolithic floors, occurs as a consequence of the existence of a joint. Such decrease for a composite slab is interpreted in the model with a single degree of freedom as the serial connection of stiffness of a monolithic slab and an element considering the existence of a contact layer. The stiffness of an element considering the existence of a contact layer decreases along with a load, and the elements corresponding to the higher stiffness of the contact layer are characterised by higher energy dissipation. The aforementioned results of the investigations confirm the assumptions of the contact layer model and a composite slab model with a single degree of freedom. The findings made represent a basis for establishing a method of evaluating the condition of a joint in composite slabs according to statistical investigations.
Go to article

Abstract

A continuous contact layer exists between the top and bottom layer of concrete composite reinforced floors. The contact layer is characterised by linear elasticity and frictional properties. In this paper a model of single degree of freedom of composite floor is determined. The model assumes that the restoring forces and the non-conservative internal friction forces dissipating energy are produced within the contact layer. A hysteresis loop is created in the process of static loading and unloading of the model, with the energy absorption coefficient being defined on this basis. The value of the coefficient is rising along with the growing stiffness of the composite. A critical damping ratio is a parameter describing free decaying vibration caused by non-conservative internal friction forces in the contact layer and in the bottom and top layer. The value of the ratio in the defined model is rising along with the lowering stiffness of the element representing contact layer. The findings resulting from the theoretical analyses carried out, including the experimental tests, are the basis for the established methods of determining the concrete layer state for reinforced concrete floors. The method is based on energy dissipation in the contact layer.
Go to article

This page uses 'cookies'. Learn more