Search results

Filters

  • Journals
  • Keywords
  • Date

Search results

Number of results: 24
items per page: 25 50 75
Sort by:

Abstract

This article presents the effects of the application of the passive method of flue gas purification from mercury compounds emitted during combustion. The research was carried out on a fluidized bed installation using coal. The dry method of acid gas pollutants reduction was applied during the combustion with the use of 9 modified sodium sorbents. They were fed into a gas jet of 573 K in two molar ratios (sodium contained in the sorbent to the sulphur contained in the fuel). The mercury emission level into the atmosphere was determined based on the mercury content in the solid substrates of the combustion process (in the fuel and the sorbent) and the solid products (fly ash and bottom waste). The combustion process was accompanied by mercury emission 14.7 μgHg/m3. During the removal of acid pollutants from fumes, a decrease in mercury concentration was achieved. The degree of the mercury reduction depended on the type the sorbent used, the manner of modification and the molar ratio in which they were fed into the installation (2 Na/S = 0.5; 2.1). Each time, the more the sorbent was fed into the installation, the bigger the reduction of the mercury emission level. Among the unmodified sorbents, the lowest emission level was achieved for the raw bicarbonate – 3.7 μgHg/m3. For baking soda it was 9.7 μgHg/m3. The application of mechanically modified compounds based on baking soda resulted in the reduction of the Hg emission in fumes up to 2.5–2.6 μgHg/m3. The determined mercury concentration levels in the gases during the purification of the fumes were compared with the accepted Hg emissions contained in the BAT conclusions for large combustion plants. As for all of the existing and newly built plants with a heat capacity below 300 MW, satisfactory effects would be achieved by the use of mechanically modified sorbents in the molar concentration of 2 Na/S = 2.1.
Go to article

Abstract

Work is being carried out on possibilities of limiting the content of mercury in hard coal products by gravity concentration of run-of-mine coal in the Branch of the Institute of Mechanized Construction and Rock Mining in Katowice and on the Faculty of Energy and Fuels of the AGH University of Science and Technology in Krakow. Under domestic industrial conditions, gravity concentration is carried out with heavy medium liquids and in jigs. Preliminary - pilot studies have shown the possibility of mercury removal also by using the dry deshaling method involving vibratory air separators. Mercury is mainly found in the pyrite and the rubble formed by the mineral carbon, but also in the organic carbon. Some of it is located in layers of coal roof fields, which in the course of their exploitation go to coal. The mercury removal efficiency during the gravity concentration process will depend on the decomposition of the listed components in the density fractions. The paper presents the results of investigations of total mercury and total sulphur content in the separated coal fractions from four mines. These contents were determined in fractions: –1.5 g/cm3 (conventionally clean coal – concentrate), 1.5–1.8 g/cm3 (conventionally middlings) and +1.8 g/cm3 (conventionally rock – waste). The results are summarized in Tables 3–5 and in Charts 1–4. Conversely, graphs 5-8 show the relationship between mercury content and total sulphur content in the tested coal samples. The study, which can be called a preliminary analysis of the susceptibility of the coals to gravity concentration, showed that the dry deshaling method on the vibratory air separators would allow significant amounts of mercury accumulated in the middlings and waste fractions to be removed.
Go to article

Abstract

Nowadays, actions allowing for a reduction of anthropogenic mercury emission are taken worldwide. Great emphasis is placed on reducing mercury emission from the processes of energochemical coal conversion, mainly from the coal combustion processes. One of the methods which enable a reduction of anthropogenic mercury emission is the removal of mercury from coal before its conversion. It should be pointed out that mercury in hard coal may occur both in the organic and mineral matter. Therefore, a universal method should allow for the removal of mercury, combined in both ways, from coal. In the paper, a concept of the hybrid mercury removal process from hard coal was presented. The idea of the process is based on the combination of the coal cleaning process using wet or dry methods (first stage) and the thermal pretreatment process at a temperature in the range from 200 to 400 °C (second stage). In the first stage, a part of mercury occurring in the mineral matter is removed. In the second stage, a part of mercury occurring in the organic matter as well as in some inorganic constituents characterized by a relatively low temperature of mercury release is removed. Based on the results of the preliminary research, the effectiveness of the decrease in mercury content in coal in the hybrid process was estimated in the range from 36 to 75% with the average at the level of 58%. The effect of the decrease in mercury content in coal is much more significant when mercury content is referred to a low heating value of coal. So determined, the effectiveness was estimated in the range from 36 to 75% with the average at the level of 58%.
Go to article

Abstract

Nairobi International Convention on the Removal of Wrecks came into force on 14th April 2015 and has been ratified by now by over 40 states across the world (among them Australia, China, India, South Africa and most of the EU countries). The convention provides legal framework for action taken by the Coastal States aiming at removal of wrecks posing danger or impediment to navigation, as well as to the marine environment, or damage to the coastline or related interests of one or more States. The Convention fills the existing legal gap by enabling the States to remove wrecks beyond their territories (as well as within if States decide so). Beside the existing international regulations like Intervention Convention or UNCLOS, the Nairobi Convention clarifies the Costal State’s rights to remove wrecks from its EEZ if they pose a danger for safe navigation or marine environment. The Convention corresponds with mentioned conventions but also equips Coastal States with new legal instruments to deal with hazardous wrecks beyond their territory. The aim of the paper is to analyse the new rights and duties of states, as well as scope of the notion of navigational and environmental threats causes by wrecks. It will refer also to regulatory problems faced by the states implementing the Convention. Even if the Convention is to be applied to territorial sea, its multiple provisions are not. Moreover, the Convention leaves many important aspects unregulated. Those issues will be analysed from the perspective of a country which has not yet ratified the Convention, and will be confronted with the experience from other jurisdictions.
Go to article

Abstract

To improve dye retention, there is a concurrent interest in the development and optimization of an alternative and promising method for the dye recovery in aqueous solutions. In this regard, considerable attention was paid to the polyoxometalates (POMs) assisted ultrafi ltration (POMAUF). The aim of the present study is to eliminate toluidine blue (TB) dye by ultrafi ltration membrane using keggin polyoxometalates (POMs) as complexing agents. In the fi rst step, the keggin polyoxometalates K3[PW12O40]∙6H2O(PW12) and K7[PW) were prepared. Then, the obtained powders were characterized by X-ray diffraction and infrared spectroscopies. Afterwards, the removal of toluidine blue (TB) using polyoxometalates assisted ultrafi ltration (POMAUF) was studied. Factors affecting the retention of dye and permeate fl ux such as transmembrane pressure, operating time, polyoxometalates concentration, ionic strength, surfactant and pH were investigated. All results of both compounds have been presented and discussed. The results reveal that the addition of POMs leads to an increase in dye retention from 11 to 95% for the PW 12 and to 98% for the PW . The results of this work have thus suggested the promising enhancement of ultrafi ltration membrane selectivity for the dye removal using new complexing agents such as POMs in place of polyelectrolytes and surfactants.
Go to article

Abstract

This paper presents the results of the investigation associated with the determination of mercury content in Polish hard coal and lignite samples. Those coals are major fuels used for electricity generation in Poland. The results indicated that the average content of mercury in the coal samples was roughly about 100 ng/g. Apart from the determination of the mercury contents a detailed ultimate and proximate analysis of the coal samples was also carried out. The relationships between the mercury content and ash, as well as fixed carbon, volatile matter, sulfur, and high heating value of the coal samples were also established. Furthermore, the effect of coal enrichment was also investigated, and it was found that the enrichment process enabled the removal of up to 75% of the coal mercury from the samples.
Go to article

Abstract

The study of the effectiveness of the removal of anionic natural organic matter (fulvic acids-FA and humic acids-HA) and inorganic anions (F-, Br-, NO3-) in MIEX®DOC process was performed. The influence of physico-chemical parameters of feed water on the process performance was investigated. The ion exchange process was carried out using strongly basic, macroporous polystyrene resin MIEX® by Orica Watercare. The synthetic feed waters differ in composition, i.e. concentration of FA and HA (ca. 6 and 12 mg/L), anions content (F-, Br-, NO3-) and of various alkalinity (ca. 20 and 120 mg/L as CaCO3) were used. The study confirmed the possibility of application of MIEX®DOC process for removal of anionic contaminants from water. It also showed the significant impact of feed water parameters on the process effectiveness. Moreover, the strong dependence of anions (F-, Br-, NO3-) removal, FA and HA concentration on the resin dose was revealed.
Go to article

Abstract

There are certain well-known methods of diminishing concentrations of nitrogen compounds, but they are ineffective in case of nitrogen-rich wastewater with a low content of biodegradable carbon. Partial nitritation followed by anaerobic ammonium oxidation (Anammox) process appear to be an excellent alternative for traditional nitrification and denitrification. This paper presents the feasibility of successful start-up of Anammox process in a laboratory-scale membrane bioreactor (MBR). It was shown that the combination of membrane technology and Anammox process allowed to create a new highly efficient and compact system for nitrogen removal. It was possible to achieve average nitrogen removal efficiency equal to 76.7 ± 8.3%. It was shown that the start-up period of 6 months was needed to obtain high nitrogen removal efficiency. The applied biochemical model of the Anammox process was based on the state-of-the-art Activated Sludge Model No.1 (ASM 1) which was modified for accounting activity of autotrophs (nitrite-oxidising bacteria and nitrateoxidising bacteria) and anammox bacteria. In order to increase the predictive power of the simulation selected parameters of the model were adjusted during model calibration. Readjustment of the model parameters based on the critically evaluated data of the reactor resulted in a satisfactory match between the model predictions and the actual observations.
Go to article

Abstract

The paper presents the results and analysis of biomass processing in order to provide the conditions for the most profitable use of the biomass in modern and efficient power generation systems with particular attention put on the decrease of the emission of carbon dioxide (CO2) and no need to develop carbon capture and storage plants. The promising concept of CO2 storage via the production of biochar and the advantages of its application as a promising carbon sink is also presented and the results are supported by authors’ own experimental data. The idea enables the production of electricity, as well as (optionally) heat and cold from the thermal treatment of biomass with simultaneous storage of the CO2 in a stable and environmentally-friendly way. The key part of the process is run in a specially-designed reactor where the biomass is heated up in the absence of oxygen. The evolved volatile matter is used to produce heat/cold and electricity while the remaining solid product (almost completely dry residue) is sequestrated in soil. The results indicate that in order to reduce the emission of CO2 the biomass should rather be ‘cut and char’ than just ‘cut and burn’, particularly that the charred biomass may also become a significant source of nutrients for the plants after sequestration in soil.
Go to article

Abstract

The paper presents the production problems related to casting using precision casting methods. The essential adverse effect of the casting process is the presence of burrs understood as oversize material necessary to remove the next finishing operations. In addition, the surfaces of the cast often characterized by a porous structure. One of the methods to improve the smoothness of the area proposed by the authors is the use of vibro-abrasive finishing. This type of treatment is widely used in the treatment of finishing small objects as well as complex shapes. Objects in the form of casting in the first step was treated with aggressive deburring polyester matrix abrasive media. The second stage was polishing, with using smoothing porcelain media. The study evaluated the effect of vibro-abrasive machining typical cast on the basic parameters of the geometric structure of the surface. Observations using optical microscope Nicon Eclipse MA 200 compared changes in surface microstructure and the effect of deburring. Clearly we can say that vibro-abrasive machining an effective way of reducing the size of burrs, smoothing and lightening the surface of objects made by casting.
Go to article

Abstract

Azo dye wastewater treatment is urgent necessary nowadays. Electrochemical technologies commonly enable more efficient degradation of recalcitrant organic contaminants than biological methods, but those rely greatly on the energy consumption. A novel process of biofilm coupled with electrolysis, i.e., bioelectrochemical system (BES), for methyl orange (MO) dye wastewater treatment was proposed and optimization of main influence factors was performed in this study. The results showed that BES had a positive effect on enhancement of color removal of MO wastewater and 81.9% of color removal efficiency was achieved at the optimum process parameters: applied voltage of 2.0 V, initial MO concentration of 20 mg/L, glucose loads of 0.5 g/L and pH of 8.0 when the hydraulic retention time (HRT) was maintained at 3 d, displaying an excellent color removal performance. Importantly, a wide range of effective pH, ranging from 6 to 9, was found, thus greatly favoring the practical application of BES described here. The absence of a peak at 463 nm showed that the azo bond of MO was almost completely cleaved after degradation in BES. From these results, the proposed method of biodegradation combined with electrochemical technique can be an effective technology for dye wastewater treatment and may hopefully be also applied for treatment of other recalcitrant compounds in water and wastewater.
Go to article

Abstract

This study investigates the influence of four imidazolium ionic liquids (ILs) present in wastewater on the activated sludge process. In addition, experiments with inactivated sludge to assess the capacity of this sorbent to remove ILs from the wastewater were conducted. It occurred that the presence of ionic liquids in wastewater reduces biomass growth and size of the sludge flocs. The strongest effect has been found for IL 6 (1-hexyl-2H-3-methyl-4,5-dimethylimidazolium iodide) with the longest alkyl chain length. Also, the degree of ILs removal increases with the alkyl chain length and decreases with the increase of initial concentration of ILs in wastewater. IL 6 reaches the highest degree of ILs removal from wastewater but inhibits the biomass growth and growth of sludge flocs in a greater extent than other tested compounds. Moreover, it was confirmed that newly synthesized ionic liquids can be adsorbed onto inactivated sludge. IL 6 could be adsorbed in a higher degree than other ionic liquids. This adsorption was described by Langmuir isotherm, whereas adsorption of other ionic liquids was described by Freundlich isotherm.
Go to article

Abstract

This article presents the results of scientific investigations on the thermal regeneration process of a sorbent of mineral origin sorbent using a retort burner. Diesel oil, a petroleum liquid, most often pervades the environment during different catastrophes. The investigated sorbent of mineral origin was used in the standard way that the Fire Service removes such petroleum liquids from the environment during disasters. For research purposes, a regeneration chamber with a retort burner was constructed. The first phase of the investigation was aimed at defining the physico-chemical features of the sorbent after subsequent cycles of the regeneration process. The second phase involved an analysis of the energy and ecological effects of the regeneration process. The results showed that the first three cycles of the regeneration process occurred under low emission conditions. The proposed regeneration method achieved a positive energetic effect with a functional heat stream with an average value of 12.4 kW (average efficiency of the regeneration chamber was 68 %). The method is very efficient, with regeneration rates between 7.2 kg/h and 8.4 kg/h. It requires only a short amount of time for the start-up and extinction of the regeneration chamber, and it is also flexible to changes in the process conditions.
Go to article

Abstract

The development of industry is determined by the use of modern materials in the production of parts and equipment. In recent years, there has been a significant increase in the use of nickel-based superalloys in the aerospace, energy and space industries. Due to their properties, these alloys belong to the group of materials hard-to-machine with conventional methods. One of the non-conventional manufacturing technologies that allow the machining of geometrically complex parts from nickel-based superalloys is electrical discharge machining. The article presents the results of experimental investigations of the impact of EDM parameters on the surfaces roughness and the material removal rate. Based on the results of empirical research, mathematical models of the EDM process were developed, which allow for the selection of the most favourable processing parameters for the expected values of the surface roughness Sa and the material removal rate.
Go to article

Abstract

Surface topography assessments with valley exploration are of great importance. Two-process surfaces are often proposed for many combustion engines. One of the errors committed in surface topography measurements and analysis are those that occur during data processing. In this paper, improper areal form removal was taken into consideration for plateau-honed cylindrical surfaces with additionally burnished oil pockets. Usually, the reference plane is established by application of: fitting algorithms (e.g. cylindrical shape), polynomials, filters and other procedures. In many cases, the influence of the reference plane was not fully recognized during valley depth consideration. Moreover, the influence of areal form removal with edge-to-dimple and valley‑to-dimple distances was not precisely defined. In this research, commonly used algorithms for form separation in surface topography analysis were proposed for the applications being considered. The digital filter bandwidth was also specified for valley depth analysis. The distortion of edge‑located oil pockets was specified. It was assumed that application of robust techniques does not necessarily provide the desired results.
Go to article

Abstract

A number of inorganic compounds, including anions such as nitrate(V), chlorate(VII), bromate (V), arsenate(III) and (V), borate and fluoride as well as metals forming anions under certain conditions, have been found in potentially harmful concentrations in numerous water sources. The maximum allowed levels of these compounds in drinking water set by the WHO and a number of countries are very low (in the range of µg/l to a few mg/l), thus the majority of them can be referred to as charged micropollutants. Several common treatment technologies which are nowadays used for removal of inorganic contaminants from natural water supplies, represent serious exploitation problems. Membrane processes such as reverse osmosis (RO), nanofiltration (NF), ultrafiltration (UF) and microfiltration (MF) in hybrid systems, Donnan dialysis (DD) and electrodialysis (ED) as well as membrane bioreactors (MBR), if properly selected, offer the advantage of producing high quality drinking water without inorganic anions. I
Go to article

Abstract

Abstract: Introduction and development of membrane techniques in the production of drinking water and purifi cation of wastewaters, in the last 40 years, was important stage in the field of water treatment effectiveness. Desalination of sea and brackish water by RO is an established way for drinking water production. Signifi cant improvements in design of RO, the application of alternative energy sources, modern pretreatment and new materials have caused the success of the process. NF is the method of water softening, because NF membranes can retain di- and multivalent ions, but to a limited extend monovalent. Drinking water containing viruses, bacteria and protozoa, as well as other microorganisms can be disinfected by means of UF. Viruses are retained by UF membranes, whereas bacteria and protozoa using both UF and MF membranes. For the removal of NOM it is possible to use direct NF or integrated systems combining UF or MF with coagulation, adsorption and oxidation. The use of NF, RO and ED, in the treatment of water containing micropollutants for drinking and industrial purposes, can provide more or less selective removal of the pollutants. The very important are disinfection byproducts, residue of pharmaceuticals and endocrine disrupting compounds. For endocrine disrupting compounds, special attention is paid onto polycyclic aromatic hydrocarbons and surface-active substances, chlorinated pesticides, phthalates, alkylphenols, polychlorinated biphenyls, hormones, synthetic pharmaceuticals and other substances disposed to the environment. The application of MF and UF in the removal of inorganic and organic micropollutants is possible in integrated systems with: coagulation, adsorption, complexion with polymers or surfactants and biological reactions.
Go to article

Abstract

The objective of this study was to investigate the possibility of using natural and bacteria-modified Erzurum clayey soil with Methylobacterium extorquens as an alternative to high cost commercial adsorbent materials for the removal of copper from aqueous solution. The copper concentrations in the samples of the polluted river water and CuCl2 solutions treated by the natural and bacteria-modified Erzurum clayey soil (ECS) have been determined by spectrophotometric method. Firstly, the surface of ECS was modified with M. extorquens and surface functionality was increased. Then, the adsorption of Cu (II) from solution phases was studied with respect to varying metal concentration, pH, and temperature and agitation time. The maximum adsorption of Cu (II) for natural and bacteria-modified Erzurum clayey soil was observed at pH: 5.0. At different copper concentrations, copper adsorption analysis was performed on 1 g using clay soil or modified clay soil. Maximum adsorption of Cu (II) was obtained as 45.7 and 48.1 mg g-1 at initial concentration (50 mg/50 mL) and optimal conditions by natural and bacteria-modified clay soil, respectively. The copper concentration was decreased in the substantial amount of the leachates solutions of natural and bacteria-modified clay soil. Langmuir and Freundlich isotherms were used to describe the adsorption behavior of Cu (II) ions. The results showed that modified clay soil had a high level of adsorption capacity for copper ion. The various thermodynamic parameters such as ΔG°, ΔH° and ΔS° were analyzed to observe the nature of adsorption. The structural properties of the natural and bacteria-modified-ECS have been characterized by SEM, FTIR and XRD techniques. Consequently, it was concluded that the bacteria-modified clay soil could be successfully used for the removal of the copper ions from the aqueous solutions.
Go to article

Abstract

Phosphorus removal and recovery from domestic wastewater is urgent nowadays. A novel process of nutrients removal coupled with phosphorus recovery from domestic sewage was proposed and optimization of induced crystallization reaction was performed in this study. The results showed that 92.3% of phosphorus recovery via induced Hydroxyapatite crystallization was achieved at the optimum process parameters: reaction time of 80 min, seed crystal loads of 60 g/L, pH of 8.5, Ca/P mole ratio of 2.0 and 4.0 L/min aeration rate when the PO43--P concentration was 10 mg/L in the influent, displaying an excellent phosphorus recovery performance. Importantly, it was found that the effect of reaction temperature on induced Hydroxyapatite crystallization was slight, thus favoring practical application of phosphorus recovery method described in this study. From these results, the proposed method of induced HAP crystallization to recover phosphorus combined with nutrients removal can be an economical and effective technology, probably favoring the water pollution control and phosphate rock recycle.
Go to article

Abstract

The aim of the study was to determine the impact of selected factors on the reduction of organic pollutants, expressed in BOD5 and CODCr, in wastewater treated in a laboratory scale model of moving bed biofilm reactor (MBBR). The factors included in the experiment: the degree of filling the fluidized bed with biomass carriers, hydraulic load, and aeration intensity. The tested model of the bioreactor consisted of five independent chambers with diameter D = 0.14 m and height H = 2.0 m, which were filled with biomass carriers at 0%, 20%, 40%, 60%, 70% of their active volume. During the test period, hydraulic loads at the level of Qh1 = 0.073 m3·m-2·h-1 and Qh2 = 0.036 m3·m-2·h-1 were applied, which ensured one-day and two-day sewage retention, respectively.The said reactors were subjected to constant aeration at P1 = 3.0 dm3·min-1 and P2 = 5.0 dm3·min-1. The highest efficiency of the reduction of the analysed indicators was demonstrated by reactors filled with carriers in the degree of 40–60%. Based on the statistical analyses (the analyses of the ANOVA variations and the Kruskal-Wallis test) carried out, it was found that the studied factors significantly modified the mutual interaction in the process of reducing BOD5 in treated wastewater of the reactors tested. The significance of the impact of the discussed factors on the values of the studied indicators in treated wastewater depends on mutual interactions between the investigated factors.
Go to article

This page uses 'cookies'. Learn more