Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 48
items per page: 25 50 75
Sort by:

Abstract

The paper presents findings from research project Mobis which is aimed at developing a method of assessing safety of unsignalised pedestrian road crossings using video image analysis. Pedestrian and vehicle traffic has been recorded at selected zebra crossing sites in Warsaw and Wrocław, before and after installation of active signage systems SignFlash and Levelite. Speeds of approaching vehicles were measured and drivers’ behaviour was classified using video analysis. The paper presents a comparison of effectiveness of systems such as SignFlash and Levelite based on changes in the mean and standard deviation of vehicle spot speeds as well as changes in speed profiles of vehicles approaching the crossings. Results indicate that both SignFlash and Levelite active signage reduce mean vehicle approach speeds and have a positive impact on drivers’ behaviour.
Go to article

Abstract

Combine harvesters are the source a large amount of noise in agriculture. Depending on different working conditions, the noise of such machines can have a significant effect on the hearing condition of drivers. Therefore, it is highly important to study the noise signals caused by these machines and find solutions for reducing the produced noise. The present study was carried out is order to obtain the fractal dimension (FD) of the noise signals in Sampo and John Deere combine harvesters in different operational conditions. The noise signals of the combines were recorded with different engine speeds, operational conditions, gear states, and locations. Four methods of direct estimations of the FD of the waveform in the time domain with three sliding windows with lengths of 50, 100, and 200 ms were employed. The results showed that the Fractal Dimension/Sound Pressure Level [dB] in John Deere and Sampo combines varied in the ranges of 1.44/96.8 to 1.57/103.2 and 1.23/92.3 to 1.51/104.1, respectively. The cabins of Sampo and John Deere combines reduced and enhanced these amounts, respectively. With an increase in the length of the sliding windows and the engine speed of the combines, the amount of FD increased. In other words, the size of the suitable window depends on the extraction method of calculating the FD. The results also showed that the type of the gearbox used in the combines could have a tangible effect on the trend of changes in the FD.
Go to article

Abstract

The accuracy of vehicle speed measured by a speedometer is analysed. The stress on the application of skew normal distribution is laid. The accuracy of measured vehicle speed depends on many error sources: construction of speedometer, measurement method, model inadequacy to real physical process, transferring information signal, external conditions, production process technology etc. The errors of speedometer are analysed in a complex relation to errors of the speed control gauges, whose functionality is based on the Doppler effect. Parameters of the normal distribution and skew normal distribution were applied in the errors analysis. It is shown that the application of maximum permissible errors to control the measuring results of vehicle speed gives paradoxical results when, in the case of skew normal distribution, the standard deviations of higher vehicle speeds are smaller than the standard deviations of lower speeds. In the case of normal distribution a higher speed has a greater standard deviation. For the speed measurements by Doppler speed gauges it is suggested to calculate the vehicle weighted average speed instead of the arithmetic average speed, what will correspond to most real dynamic changes of the vehicle speed parameters.
Go to article

Abstract

The paper reports the study of the complexation processes in aqueous solution of α-CD and DMSO. Cyclodextrins (CDs) (sometimes called cycloamyloses) are cyclic oligosaccharides formed by glucose units interconnected by α-(1,4) linkages; α-CD is one of three the most common CDs. It consists of six glucopyranose units. The speed of ultrasonic waves has been measured by the resonance method on ResoscanTM System apparatus. Some collateral data, such as density and heat capacity of the system, have also been measured. On the basis of the experimental data the excess adiabatic compressibility was determined. The extremes of the excess adiabatic compressibility function for different mixture compositions allowed us to establish the composition of molecular complexes formed in the solution. The obtained results suggest the formation of the α-CD with DMSO inclusion complexes with chemical stoichiometric ratio value of 1:1.
Go to article

Abstract

This paper presents a position sensorless drive of non salient pole PM synchronous motors for all speeds including zero speed. Using adaptive Lyapunov design a new approach for the design of an observer is developed. The resulting scheme leads to a nonlinear full order observer for the motor states including the rotor speed. Assuming motor parameters known the design achieves stability with guaranteed region of attraction even at zero speed. The control method is made robust at zero and low speed by changing the direct vector current component to a value different from zero. In order to verify the applicability of the method the controller has been implemented and tested on a 800 W motor.
Go to article

Abstract

Focus of the vibration expert community shifts more and more towards diagnosing machines subjected to varying rotational speeds and loads. Such machines require order analysis for proper fault detection and identification. In many cases phase markers (tachometers, encoders, etc) are used to help performing the resampling of the vibration signals to remove the speed fluctuations and smearing from the spectrum (order tracking). However, not all machines have the facility to install speed tracking sensors, due to design or cost reasons, and the signal itself has to then be used to extract this information. This paper is focused on the problem of speed tracking in wind turbines, which represent typical situations for speed and load variation. The basic design of a wind turbine is presented. Two main types of speed control i.e. stall and pitch control are presented,. The authors have investigated two methods of speed tracking, using information from the signal (without relying on a speed signal). One method is based on extracting a reference signal to use as a tachometer, while the other is phase-based (phase demodulation). Both methods are presented and applied to the vibration data from real wind turbines. The results are compared with each other and with the actual speed data.
Go to article

Abstract

Modern regulations concerning railway bridges are based on the approach of structural dynamics, which is described in PN-EN standards. This paper presents the results of theoretical dynamic analysis of the HSLM-A train set loading on the structure of a pre-stressed concrete arch bridge - the first railway bridge of its type which was built in Poland (completed in 1959). The recommendations of PN-EN have been followed and modal analysis was carried out to define the sensitivity of the structure to chosen eigenforms. Additionally the paper presents a course of calculations and the conclusions obtained from the analysis of displacements, accelerations, and bending moments induced in the structure through a simulated passage of a high-speed train in the context of the requirements of PN-EN Standards. The conclusions from the current calculations can be used for dynamic analysis of bridges of similar structural solutions.
Go to article

Abstract

In recent years adverse processes of suburbanization have been observed in cities. It has become a serious challenge for urban and transport planners, as it influences largely the quality of space, the quality of life, and the cost of running the city. This paper is dedicated to travel models in areas serviced by a railway system, and is based on a real-life survey example of the Błonie community, a district belonging to the Warsaw metropolitan area. Research carried out in 2014 focused on combined travels behaviors recorded using GPS locators as well as quantitative research (volumes of users across various transport systems).
Go to article

Abstract

The author investigated traffic flow quality on a new 2+1 long road bypass with an exceptionally high share of heavy vehicles in order to assess rational limits of heavy vehicle shares in traffic flow, dependent on the length of the 2+1 road and the number of passing segments in each direction. This paper presents the results of traffic flow quality analyses through the use of empirical and simulation methods for a single 2+1 road segment with additional passing lanes, as well as for the study of the entire section of the bypass – 2+1 road. Variables include analysis of travel speed distribution, platoon traffic, and amount of passing maneuvers. Results show that large passing demands lead to very high speeds (over 100 km/h) on segments with additional passing lanes. The conclusions include remarks related to the use and operation of 2+1 cross-sections with high shares of heavy vehicles.
Go to article

Abstract

An emerging ultrasonic technology aims to control high-pressure industrial processes that use liquids at pressures up to 800 MPa. To control these processes it is necessary to know precisely physicochemical properties of the processed liquid (e.g., Camelina sativa oil) in the high-pressure range. In recent years, Camelina sativa oil gained a significant interest in food and biofuel industries. Unfortunately, only a very few data characterizing the high-pressure behavior of Camelina sativa oil is available. The aim of this paper is to investigate high pressure physicochemical properties of liquids on the example of Camelina sativa oil, using efficient ultrasonic techniques, i.e., speed of sound measurements supported by parallel measurements of density. It is worth noting that conventional low-pressure methods of measuring physicochemical properties of liquids fail at high pressures. The time of flight (TOF) between the two selected ultrasonic impulses was evaluated with a cross-correlation method. TOF measurements enabled for determination of the speed of sound with very high precision (of the order of picoseconds). Ultrasonic velocity and density measurements were performed for pressures 0.1–660 MPa, and temperatures 3–30XC. Isotherms of acoustic impedance Za, surface tension #27; and thermal conductivity k were subsequently evaluated. These physicochemical parameters of Camelina sativa oil are mainly influenced by changes in the pressure p, i.e., they increase about two times when the pressure increases from atmospheric pressure (0.1 MPa) to 660 MPa at 30XC. The results obtained in this study are novel and can be applied in food, and chemical industries.
Go to article

Abstract

When the machine is at high speed, serious problems occur, such as high frequency loss, difficult thermal management, and the rotor structural strength insufficiency. In this paper, the performances of two high-speed permanent magnet generators (HSP- MGs) with different rotational speeds and the same torque are compared and analyzed. The two-dimensional finite element model (FEM) of the 117 kW, 60 000 rpm HSPMG is established. By comparing a calculation result and test data, the accuracy of the model is verified. On this basis, the 40 kW, 20 000 rpm HSPMG is designed and the FEM is established. The relationship between the voltage regulation sensitivity and power factor of the two HSPMGs is determined. The influence mechanism of the voltage regulation sensitivity is further revealed. In addition, the air-gap flux density is decomposed by the Fourier transform principle, and the influence degree of different harmonic orders on the HSPMG performance is determined. The method to reduce the harmonic content is further proposed. Finally, the method to improve the HSPMG overload capacity is obtained by studying the maximum power. The research showed that the HSPMG at low speed (20 000 rpm) has high sensitivity of the voltage regulation, while the HSPMG at high speed (60 000 rpm) is superior to the HSPMG at low speed in reducing the harmonic content and increasing the overload capacity.
Go to article

Abstract

IIn this short communication, we revise a correlation for the saturated liquid isothermal compressibility based on the data available in DIPPR (Postnikov, 2016) which considers the molecular non-sphericity and addresses a problem of predicting speeds of sound in saturated long-chained alkanes. In addition, we correct a misprint appeared in the cited work and provide programming code used for the realisation of the proposed calculations.
Go to article

Abstract

In this paper, an attempt was made to explain the causes of surface delamination in high carbon steel wires during the torsion test. For end wires with 1.7 mm diameter drawn at speeds of 5, 10, 15, 20, 25 m/s, technological tests were carried out. Then the susceptibility of the wire to plastic strain was determined. The microstructure analysis complemented the research. Analysis of the fracture torsion test showed that the wires drawn at speeds exceeding 15 m/s are delamination, which disqualify it as a material for a rope and a spring. The source of delamination in high carbon steel wires is their stronger strengthening, especially of the surface layer, which leads to a decrease in the orientation of the cementite laminaes and an increase in the degree of their fragmentation.
Go to article

Abstract

This paper presents the results of numerical analysis of aerodynamic characteristics of a sports car equipped with movable aerodynamic elements. The effects of size, shape, position, angle of inclination of the moving flaps on the aerodynamic downforce and aerodynamic drag forces acting on the vehicle were investigated. The calculations were performed with the help of the ANSYS-Fluent CFD software. The transient flow of incompressible fluid around the car body with moving flaps, with modeled turbulence (model Spalart-Allmaras or SAS), was simulated. The paper presents examples of effective flap configuration, and the example of configuration which does not generate aerodynamic downforce. One compares the change in the forces generated at different angles of flap opening, pressure distribution, and visualization of streamlines around the body. There are shown the physical reasons for the observed abnormal characteristics of some flap configurations. The results of calculations are presented in the form of pressure contours, pathlines, and force changes in the function of the angle of flap rotation. There is also presented estimated practical suitability of particular flap configurations for controlling the high-speed car stability and performance.
Go to article

Abstract

An analysis of the effect of drawing speed on the formation of a zinc coating in the multi-stage fine steel wire drawing process has been carried out in the article. Pre-hardened 2.2 mm-diameter material was drawn into 1.00 mm-diameter wire in 6 draws on a multi-stage drawing machine. The drawing process was carried out at a drawing speed of 5, 10, 15, 20 and 20 m/s, respectively. Mechanical tests were tests were performed for the final wires to determine their yield strength, ultimate tensile strength, uniform and total elongation and reduction in area. The thickness of the zinc coating on the wire surface was determined by the gravimetric method and based on metallographic examination. The use of electron scanning microscopy, on the other hand, enabled the identification of individual phases in the zinc coating. The above investigations were supplemented with corrosion testing of 1.00 mm-diameter wires. It has been demonstrated that drawing speed significantly influences not only the thickness of the zinc coating on the drawn wire surface, buts also its morphology and corrosion resistance.
Go to article

Abstract

Touch-trigger probes for CNC milling machines usually use wireless communication in the radio or IR band. Additionally they enable triggering signal filtering in order to avoid false triggers of the probe. These solutions cause a delay in trigger signal transmission from the probe to the machine tool controller. This delay creates an additional pre-travel component, which is directly proportional to the measurement speed and which is the cause of a previously observed but not explained increase of the pre-travel with the increase of the measurement speed. In the paper, a method of testing the delay time of triggering signal is described, an example of delay time testing results is presented and the previous, unexplained results of other researchers are analysed in terms of signal transmission delay.
Go to article

Abstract

This paper proposes a unique method of an error detection and correction (EDAC) circuit, carried out using arithmetic logic blocks. The modified logic blocks circuit and its auxiliary components are designed with Boolean and block reduction technique, which reduced one logic gate per block. The reduced logic circuits were simulated and designed using MATLAB Simulink, DSCH 2 CAD, and Microwind CAD tools. The modified, 2:1 multiplexer, demultiplexer, comparator, 1-bit adder, ALU, and error correction and detection circuit were simulated using MATLAB and Microwind. The EDAC circuit operates at a speed of 454.676 MHz and a slew rate of -2.00 which indicates excellence in high speed and low-area.
Go to article

Abstract

Condition monitoring of machines working under non-stationary operations is one of the most challenging problems in maintenance. A wind turbine is an example of such class of machines. One of effective approaches may be to identify operating conditions and investigate their influence on used diagnostic features. Commonly used methods based on measurement of electric current, rotational speed, power and other process variables require additional equipment (sensors, acquisition cards) and software. It is proposed to use advanced signal processing techniques for instantaneous shaft speed recovery from a vibration signal. It may be used instead of extra channels or in parallel as signal verification.
Go to article

Abstract

The paper analyzes the effect of ageing on the variations in the mechanical and technological properties of steel wire. The process of drawing 5.5 mm-diameter wire rod into 1.70 mm wire was carried out in 12 draws on a Koch KGT multi-stage drawing machine in the drawing velocity range of 5-25 m/s. Finished 1.7 mm-diameter wires after, respectively, 1, 24, 720 and 8760 hours of the completion of the drawing process were subjected to testing to determine their mechanical and technological properties. The yield strength, YS; tensile strength, UTS; uniform elongation, Ar; total elongation, Ac; reduction of area, Z; number of twists, Nt; and the number of bends, Nb, have been determined. It has been demonstrated that variations in mechanical properties occur after the multi-stage drawing process due to ageing, with their degree and mode being dependent on the drawing speed.
Go to article

Abstract

The paper presents properties of HS6-5-2 high speed steel subjected to deep cryogenic treatment (DCT) and subsequent tempering at different temperatures. DCT process of HS6-5-2 steel leads to shifting of maximum hardness peak to the lower temperature and the reduction of the obtained maximum hardness by about 1 HRC. These changes in hardness may be due to the shifting of the stage of nucleation and growth of carbide phases to lower temperatures or the changes taking place in the matrix, connected with the additional transformation of the martensite proceeding during the isothermal martensitic transformation occurring at cryogenic temperatures and more extensively occurring precipitation processes, lowering the content of the carbon in the martensite, determining thereby its lower hardness.
Go to article

Abstract

This paper describes the arithmetic blocks based on Montgomery Multiplier (MM), which reduces complexity, gives lower power dissipation and higher operating frequency. The main objective in designing these arithmetic blocks is to use modified full adder structure and carry save adder structure that can be implemented in algorithm based MM circuit. The conventional full adder design acts as a benchmark for comparison, the second is the modified Boolean equation for full adder and third design is the design of full adder consisting of two XOR gate and a 2-to-1 Multiplexer. Besides Universal gates such as NOR gate and NAND gate, full adder circuits are used to further improve the speed of the circuit. The MM circuit is evaluated based on different parameters such as operating frequency, power dissipation and area of occupancy in FPGA board. The schematic designs of the arithmetic components along with the MM architecture are constructed using Quartus II tool, while the simulation is done using Model sim for verification of circuit functionality which has shown improvement on the full adder design with two XOR gate and one 2-to-1 Multiplexer implementation in terms of power dissipation, operating frequency and area.
Go to article

Abstract

In multi-stage wire drawing machines productivity growth can be achieved at higher drawing speeds by preventing wire breakage during the process. One disadvantage of high-speed wire drawing is the requirement imposed by machine dynamics in terms of its stability and reliability during operation. Tensile forces in the wire must maintained by fast synchronization of all capstans speed. In this process, the displacement sensors play the main role in providing the control system with feedback information about the wire condition. In this study, the influences between the sensors and actuator driven capstans have been studied, and tuner roll concept of a wire drawing machine was experimentally investigated. To this aim, measurements were carried out on two drawing stages at different drawing speeds and obtained results were presented. These results clearly show the fast changes of the capstans speed and the angular displacements of the rollers that tighten the wire, which only confirms the high dynamics of the wire drawing machine.
Go to article

Abstract

The paper analyses a possibility of utilising the information which is contained in DIPPR database for a calculation of the speed of sound, which is absent there. As an example, liquid hydrocarbons are considered: n-hexane, 1-hexene, cyclohexane, cyclohexene, benzene, and 1-hexanols, as well as representatives of n-alkanes with various hydrocarbon chain lengths. It is shown that the Brelvi-O’Connell correlation for the reduced bulk modulus, supplied with the correlations for the internal pressure at the normal boiling temperature, results in the values having accuracy comparable with other DIPPR data for the region below the boiling point bounded by the values of the reduced density around ρr ≈ 3.5. The source of errors originated from the Brelvi-O’Connell correlation for larger reduced densities is discussed.
Go to article

Abstract

The aim of this paper is to answer the question: Are the Łódź Hills useful for electrical energy production from wind energy or not? Due to access to short-term data related to wind measurements (the period of 2008 and 2009) from a local meteorological station, the measure – correlate – predict approach have been applied. Long-term (1979‒2016) reference data were obtained from ECWMF ERA-40 Reanalysis. Artificial neural networks were used to calculate predicted wind speed. The obtained average wind speed and wind power density was 4.21 ms⁻¹ and 70 Wm⁻¹, respectively, at 10 m above ground level (5.51 ms⁻¹, 170 Wm⁻¹ at 50 m). From the point of view of Polish wind conditions, Łódź Hills may be considered useful for wind power engineering.
Go to article

Abstract

Modern electronics systems consist of not only with the power electronics converters, but also with the friendly user interface which allow you to read the operating parameters and change them. The simplest solution of the user interface is to use alphanumeric display which displays information about the state of the converter. With a few additional buttons you can change the settings. This solution is simple, inexpensive but allows only local control (within walking distance from the system) and the number of displayed information is low. You can create extensive menu, but it causes problems with access to information. This paper presents the example of a rotating energy storage universal solution which is lack of the above mentioned disadvantages.
Go to article

This page uses 'cookies'. Learn more