Microscale combined heat and power (CHP) unit based on solid oxide fuel cells (SOFC) for distributed generation was analyzed. Operation principle is provided, and the technology development in recent years is briefly discussed. System baseline for numerical analysis under steady-state operation is given. Grid-connected unit, fuelled by biogas corresponds to potential market demand in Europe, therefore has been selected for analysis. Fuel processing method for particular application is described. Results of modeling performed in ASPEN Plus engineering software with certain assumptions are presented and discussed. Due to high system electrical efficiency exceeding 40%, and overall efficiency over 80%, technology is an example of highly competitive and sustainable energy generation unit.
Developed within the frame of cognitive linguistics and cognitive science, the present paper argues that the wave-stream model is a more adequate manner of representing verbal grams in Biblical Hebrew than neat models built on discrete, binary and static categories. Taking as examples two Biblical Hebrew verbal grams (WAYYIQTOL and QATAL) and building on the empirical evidence concerning the senses conveyed by these two forms in the book of Genesis, the author demonstrates the following: a) Neat, binary, discrete and static models correspond to “folk” representations of reality; b) A more adequate representation, which preserves the complex nature of language and its components, is provided by the wave-stream model; c) The wave-stream model additionally suggests the psychological reality of the grams or their conceptualizations by speakers. As a result, the wave-stream model has both etic (language centric) and emic (psychological or human centric) dimensions, the latter being derived in a principled manner.
In this paper, the author compares the of characteristics of subsystems obtained by the approximate and exact method in order to answer to the question - if the approximate method can be used to nominate the characteristics of mechatronic systems. Frequency - modal analysis has been presented for a mechanical system, i.e. transverse-vibrating clamped-free beam. Consequently, the model of the beam was presented in a five-vertex hypergraph. This model, in the case of approximate frequency-modal analysis, can be imitated in a three-vertex hypergraph. Such formulation could be the introduction to synthesis of transverse-vibrating complex beam systems with constant cross-section.
Based on the publications regarding new or recent measurement systems for the tokamak plasma experiments, it can be found that the monitoring and quality validation of input signals for the computation stage is done in different, often simple, ways. In the paper is described the unique approach to implement the novel evaluation and data quality monitoring (EDQM) model for use in various measurement systems. The adaptation of the model is made for the GEM-based soft X-ray measurement system FPGA-based. The EDQM elements has been connected to the base firmware using PCI-E DMA real-time data streaming with minimal modification. As additional storage, on-board DDR3 memory has been used. Description of implemented elements is provided, along with designed data processing tools and advanced simulation environment based on Questa software.
In 2015 an important part of the official evaluation of Polish scientific journals was left to experts’ judgement. In this paper we try to establish which observable factors (with available data) are closely related to the outcome of experts’ evaluation of Polish journals in economic sciences. Using the multiple regression statistical model we show that only 5 variables (out of 17) significantly explain almost 50% of the empirical variance of the experts’ evaluation. The determinants of particular interest, not entering the formal criteria and not related to the impact on global science, are: the number of citations mainly in Polish journals and the affiliation with the Polish Academy of Sciences.
The article covers the systematic basis for the creation of new technological processes of corn harvesting machines. Modern corn-harvesting machines have reached certain thresholds according to their technological properties that most significantly affect the final production and economic indicators of planting corn for grain efficiency, still they do not meet modern requirements. The technological properties mentioned above are hardly adjusted for wide range of physical and mechanical properties of the plants and crop parameters. This situation is caused by new machine´s working parts being viewed by researchers and developers as complex technical systems not from the standpoint of general systems theory but in terms of the use of traditional knowledge of the laws of agricultural mechanics, thus not getting proper attention to their systematic coordination with working conditions. Based on this, the paper presents a structural scheme for the system “mechanized corn for grain harvesting”, key elements of which are: agricultural (А), engineering (В) and selectional (С) supply. Interconnection of the subsystem´s elements and their consistency determine the effectiveness of the whole process. Inconsistency of the links АВ and ВC is observed. The conceptual system “mechanized corn for grain harvesting” design relates to the field with clear NO-factors: incompleteness, uncertainty, inconsistency and lack of information for decision making, thus it is important to review tasks of conceptual design from the most general constructual standpoint. The method of describing systems at the conceptual level is suggested. This systematic representation of corn-harvesting machines allows to approach the task of their workflows modeling from the most general standpoint.
Balanced distribution of air in coal-fired boiler is one of the most important factors in the combustion process and is strongly connected to the overall system efficiency. Reliable and continuous information about combustion airﬂow and fuel rate is essential for achieving optimal stoichiometric ratio as well as efficient and safe operation of a boiler. Imbalances in air distribution result in reduced boiler efficiency, increased gas pollutant emission and operating problems, such as corrosion, slagging or fouling. Monitoring of air ﬂow trends in boiler is an effective method for further analysis and can help to appoint important dependences and start optimization actions. Accurate real-time monitoring of the air distribution in boiler can bring economical, environmental and operational benefits. The paper presents a novel concept for online monitoring system of air distribution in coal-ﬁred boiler based on real-time numerical calculations. The proposed mathematical model allows for identification of mass ﬂow rates of secondary air to individual burners and to overﬁre air (OFA) nozzles. Numerical models of air and flue gas system were developed using software for power plant simulation. The correctness of the developed model was verified and validated with the reference measurement values. The presented numerical model for real-time monitoring of air distribution is capable of giving continuous determination of the complete air flows based on available digital communication system (DCS) data.
The primary aim of this research study was to model acoustic conditions of the Courtyard of the Gdańsk University of Technology Main Building, and then to design a sound reinforcement system for this interior. First, results of measurements of the parameters of the acoustic field are presented. Then, the comparison between measured and predicted values using the ODEON program is shown. Collected data indicate a long reverberation time which results in poor speech intelligibility. Then, a thorough analysis is perform to improve the acoustic properties of the model of the interior investigated. On the basis of the improved acoustic model two options of a sound reinforcement system for this interior are proposed, and then analyzed. After applying sound absorbing material it was noted that the predicted speech intelligibility increased from bad/poor rating to good category.
The generic mathematical model and computational algorithm considering hydrodynamics, heat and mass transfer processes during casting and forming steel ingots and castings are offered. Usage domains for turbulent, convective and non-convective models are determined depending on ingot geometry and thermal overheating of the poured melt. The expert system is developed, enabling to choose a mathematical model depending on the physical statement of a problem.
The paper contains selected results of research on the Domestic Power System (DPS) as an unmanned factory. Models of the DPS system of the MISO type, obtained as a result of identification for 14 inputs and 4 outputs were presented. Particular attention was given to the identification and the assessment of the DPS development based on the systems and control theory. The obtained models of the DPS development were analyzed and discussed. The studies were obtained model of the development of the DPS, and on the basis of is knowledge of the structural and parametrical changes of system development. The model can be used to analyze the design and development of the system from the point of view of the growth of internal organization system and the transition to higher levels of control.
The article concerns computer modelling of processes in cooling systems of internal combustion engines. Modelling objectives and existing commercial programs are presented. It also describes Author’s own method of binding graphs used to describe phenomena in the cooling system of a spark ignition engine. The own model has been verified by tests on the engine dynamometer. An example of using a commercial program for experimental modelling of an installation containing a heat accumulator is presented.
The paper focuses on the modelling of bromate formation. An axial dispersion model was proposed to integrate the non-ideal mixing, mass-transfer and a kinetic model that links ozone decomposition reactions fromthe Tomiyasu, Fukutomi and Gordon (TFG) ozone decaymodelwith direct and indirect bromide oxidation reactions, oxidation of natural organicmatter and its reactionswith aqueous bromine. To elucidate the role of ammonia an additional set of reactions leading to bromamine formation, oxidation and disproportionation was incorporated in the kinetic model. Sensitivity analysis was conducted to obtain information on reliability of the reaction rate constants used and to simplify the model.
“Mineral deposit model”, “deposit modelling” are the terms commonly used, although imprecise. This is often identified as the application of computerized methods to the elaboration and presentation of geological information, in particular for the mining design. Deposit modelling is the mode of presentation of deposit features, which in the meaning of the authors of such presentation, describes the deposit features between the points of observations as best as possible. Deposit modelling has a long history (XVI-XVII centuries), however such a term was not used. Varied methods of cartographic presentation of deposits and their features were proposed. The progress in the presentation of the deposit in space using isolines maps has led to the separation of methods of deposits geometrisation. Over time, a simple mathematical statistics method was used to describe the deposit parameters, followed by geostatistical methods. Some of them were however not commonly used as too troublesome. The computer based approach to the presentation of geological data has an unquestionable value but is accompanied by the possibility of inappropriate formalized and erroneous interpretations and a presentation as to whether the basic rules of geological knowledge were neglected. Deposits modeling is a conceptual task and cannot be fully automated.
Exploitation of hard coal seams by roadway system is applied by two coal mines in southern Poland in Upper Silesian Basin. It is a secondary mining exploitation carries out in safety pillars of urban areas and shafts within mining areas of closed coal mines. Roadway system is the excavation process of gateways which are made in parallel order leaving coal pillars between them. An optimal width of coal pillar makes roadway stable and reduces subsidence of terrain surface. The article presents results of subsidence simulation caused by partial extraction using empirical and numerical methods on the example of one exploitation field of “Siltech” coal mine. The asymptotic state of subsidence was considered after mining ceased in the study area. In order to simulate of subsidence, numerical model of rock mass and model of Knothe-Budryk theory were calibrated. Simulation of vertical displacements in numerical method was carried out using RS3 program by Rocscience based on finite element method. The assumption was made that model of rock mass is transversely isotropic medium, in which panels were designed according to order of extraction of coal seams. The results of empirical and numerical methods were compared with measured values of subsidence at benchmarks along drawn lines (subsidence profiles).
Four Geodynamical Expeditions of the Polish Academy of Sciences carried through wide research seismic program in West Antarctica in 1979-1991. Three of these expeditions operated in the Bransfield Strait. The experiment of deep refraction and wide-angle reflection in West Antarctica focused on deep structure of the lithosphere, mainly of the Earth's crust. The network of deep seismic soundings (DSS) profiles covered all the Bransfield Strait. Five land stations on the South Shetland Islands, three stations on the Antarctic Peninsula and nine ocean bottom seismographs (OBS) recorded seismic waves, generated by explosions in a sea. The Bransfield Rift and the Bransfield Platform form a marginal basin against a volcanic arc of the South Shetland Islands. The paper presents new results of 2-D seismic modeling for network of five selected profiles. Four of them, ranging in lenght from 150 to 190 km, crossed main structures of the Bransfield Strait and the fifth, which connected the other ones and was 310 km long, ran along the Bransfield Rift. Two or three seismic models were presented for each profile. Finally, mutually corrected and controlled 2-D models of described profiles were constructed. They all presented spatial complex structure of the Earth's crust in a young rift of the Bransfield Strait, including extent of its main element i.e. anomalous high velocity body (HVB) (Vp > 7.4 km/s), detected in 10-30 km depth range except profile DSS-4 (southwest part of the Bransfield Strait). This inhomogeneity is interpreted as intrusion of the upper mantle (?asthenosphere) during stretching of the continental crust. The Moho discontinuity was found at depth 30-35 km, with velocities equal to about 8.1 km/s.
The contemporary underground mining of raw minerals is more and more associated with geological and mining software packages which support the work of designers from the moment of the exploration of a deposit, determination of its size and quality, geological, hydrogeological and tectonic conditions, by planning the development and cutting of the deposit. Production planning is one of the most important activities carried out in the course of a mining project, because it allows to set specific production results of a mine in relation to a time unit, and then allows for a verification of the degree of completion of the assumed plan. At present, computer-aided design is applicable to daily or long-term output planning taking deposit, qualitative, quantitative and cost constraints into account. In the article, selected forms of ore deposits were presented. On the basis of several dozen boreholes up to 300m in length, an exemplary fragment of the ore cutting model using computer-aided design of mining works was presented. By using modern computer software - ABB MineScape with modular construction, the possibilities of improving the process of development of future exploitation areas have been determined. In particular, the arrangement of boreholes, based on which ones the cross sections were made with, present the exemplary lithostratigraphic thickness of layers, including the location of discontinuous deformations in the form of faults, and an ore bearing zone. For the block model, resources with priority for metal N o. 1 and 2 were calculated. I n the last section of the article, the cutting idea for a shallow ore deposit has been presented. The degree of effective use of the deposit has been analysed for the room and pillar mining method.
The analysis of changes in the mechanical properties of wooden mining cribs under the influence of different types of exploitation loads is the question for which deals with many domestic and abroad research centers deal with. High The high interest in this subject results from the increase of the conducted depth exploitation, which contributes to the increase in both the vertical pres-sure and the complexity of geological – mining conditions and in- the intensification of natural hazards. Another reason is the tendency of decreasing the thickness of the exploited ores deposits. Wooden crib support is used Both both in underground ore, hard coal and salt mining is used wooden crib support. Mining cribs with various configurations are especially useful for the reinforcement of excavations workings behind the front and for further strengthen of the crossings. In particular, additional reinforcement support in the form of wooden cribs (pile supporting), which shall be left empty or filled with waste rock is applied in the ore mining in places where found extended rooms or drifts are found or in places with degraded roof conditions, applies additional reinforcement support in the form of wooden cribs (pile supporting), which shall be left empty or filled with waste rock. During underground ex-ploitation is produced waste Waste rock, which comes from the access, prepar-atory excavations and from ongoing field of exploitation is produced during underground exploitation. In the case of the underground exploitation of cop-per ore, waste rock is used to fill voids after exploitation as rock stowing. It is also used for filling mining wooden cribs, as an artificial support and for harder transportation roads. This paper presents the results of the laboratory strength tests performed on models of four-point timber cribs, built with beams set horizontally, at the ge-ometrical scale of 1:10. In the laboratory research Research wooden cribs models with size 200 × 200 × 200 mm and 100 × 100 × 100 mm were used in the laboratory. The paper describes the maximum loading capacity of the cribs consisted consisting only of beams and filled with waste rocks. In addition, a vertical and appropriate strain of cribs at maximum force was shown. On the basis of laboratory research it was found that the use of the same number of timbers and the management of waste rocks, the filling of the four-point cribs with the waste rocks allowed several times to increase its support to be increased several times.
Validation results of a theoretical model that describes the formation of bromate during ozonation of bromide-containing natural waters are presented. An axial dispersion model integrating the nonideal mixing, mass-transfer and a kinetic model that links ozone decomposition reactions from the Tomiyasu, Fukutomi and Gordon ozone decay model with direct and indirect bromide oxidation reactions, oxidation of natural organicmatter and reactions of dissolved organics and aqueous bromine was verified. Themodel was successfully validated with results obtained both at a laboratory and a full scale. Its applicability to different water supply systems was approved.
The paper presents modeling and simulation results of the operation of a three-phase fluidized bed bioreactorwith partial recirculation of biomass. The proposed quantitative description of the bioreactor takes into account biomass growth on inert carriers, microorganisms decay and interphase biomass transfer. Stationary characteristics of the bioreactor and local stability of steady-stateswere determined. The influence of microbiological growth kinetics on the multiplicity of steady-states was discussed. The relationship between biofilm growth and boundaries of fluidized bed existence was shown.
The author analyses onymic practices of Poznań–based craftsmen forming guilds. In the names of the inhabitants of Poznań, which stabilised until the end of the 18th century, she seeks traces of the so-called cognomens, i.e. secondary personal designations granted to apprentices who were becoming masters. The names resulted from community acts of creation, which were of ludic nature. Referring to German onymic practices and pointing to the so-called Schleifnamen, the author discusses specific codes of European middle-class culture. She focuses on the transfer of models and patterns to Polish urban communities.
Given a linear discrete system with initial state x0 and output function yi , we investigate a low dimensional linear systemthat produces, with a tolerance index ǫ, the same output function when the initial state belongs to a specified set, called ǫ-admissible set, that we characterize by a finite number of inequalities. We also give an algorithm which allows us to determine an ǫ-admissible set.
The complexity of the phenomena associated with the course of the cognitive processes that determine an efficient learning, excludes the possibility of collecting knowledge in other ways than neuronal-information. It excludes also possibilities of interpreting it, in other ways than with use of respectively formalized cognitive models. The presented paper is a kind of summary of the latest achievements in this field.
The article presents a synthetic analysis of the crude oil market in Poland. As of today, this safety is provided mainly on the basis of native lignite and hard coal resources. However, the analysis of the hard coal market conducted by the authors indicates that the carried out mining restructuring (among others) led to an excessive reduction of mining volume and employment level in the hard coal mining sector. This led to a precedent situation when Poland became an importer of this energy carrier. In addition, the European Union’s requirements for greenhouse gas emissions must be taken into account. In connection with the above, it is necessary to search for new energy sources or technologies that enable hard coal to meet the requirements. It is possible to apply the so-called clean coal technologies that allow the greenhouse gas emissions generated during coal combustion to be reduced. As of today, they are not used on a mass scale, because the use of this type of technology involves additional financial expenses. However, taking into account that technologies have been growing faster and faster, are modernized in a shorter time, making a breakthrough discovery took hundreds of years, now it is often a few months, clean coal technologies can become the optimal solution in the near future. It is also necessary to diversify the sources of obtaining imported energy carriers. The article describes coal and crude oil in terms of their mutual substitution. The article is a continuation of research conducted by the authors. Previous publications presented considerations on analogous topics related to natural gas and renewable energy sources. The crude oil market in Poland was analyzed and forecasts for oil extraction and the demand in the world and Poland by 2023 were presented. The SARIMA model was also created. The model made it possible to obtain oil an prices forecast.
During four Polish Geodynamical Expeditions to West Antarctica between 1979 and 1991, seismic measurements were made along 21 deep refraction profiles in the Bransfield Strait and along the coastal area of Antarctic Peninsula using explosion sources. Recordings were made by 16 land stations and 8 ocean bottom seismometers. Good quality recordings were obtained up to about 250 km distance. This allowed a detailed study of the seismic wave field and crustal structure. Three-dimensional tomographic inversion was carried out using first arrivals from the complete data set including off-line recordings. As a result, we obtained a 3-D model of the P-wave velocity distribution in the study area. In the area adjacent to the Antarctic Peninsula coast, sedimentary cover of 0.2 to 3 km thickness was found, whereas in the shelf area and in the Bransfield Strait sedimentary basins with thickness from 5 to 8 km were observed. In the Bransfield Strait a high velocity body with Vp > 7.5 km/s was found at 12 km depth. The use of the off-line data allowed for determination of the horizontal extent of the body. The thickness of the crust varies from more than 35-40 km in the coastal area south of the Hero Fracture Zone to 30-35 km in the area of Bransfield Strait and South Shetland Islands and about 12 km in the Pacific Ocean NW of South Shetland Islands.