Applied sciences

Opto-Electronics Review

Content

Opto-Electronics Review | 2017 | vol. 25 | No 1

Download PDF Download RIS Download Bibtex

Abstract

We experimentally studied three different D-shape polymer optical fibres with an exposed core for their applications as surface plasmon resonance sensors. The first one was a conventional D-shape fibre with no microstructure while in two others the fibre core was surrounded by two rings of air holes. In one of the microstructured fibres we introduced special absorbing inclusions placed outside the microstructure to attenuate leaky modes. We compared the performance of the surface plasmon resonance sensors based on the three fibres. We showed that the fibre bending enhances the resonance in all investigated fibres. The measured sensitivity of about 610 nm/RIU for the refractive index of glycerol solution around 1.350 is similar in all fabricated sensors. However, the spectral width of the resonance curve is significantly lower for the fibre with inclusions suppressing the leaky modes.

Go to article

Authors and Affiliations

K. Gasior
T. Martynkien
G. Wojcik
P. Mergo
W. Urbanczyk
Download PDF Download RIS Download Bibtex

Abstract

A dual-wavelength optical polarimetric approach has been proposed as a means of elimination of the systematic errors and estimation of the optical anisotropy parameters for a single DKDP crystal. Our HAUP-related polarimeter uses two semiconductor lasers with the neighbouring wavelengths of 635 nm and 650 nm. Based on the temperature dependence analysis of small characteristic azimuths of light polarization with respect to the axis of the sample, we found the parameters of imperfections of polarization system. We acquired eigen waves ellipticities in a DKDP crystal and found perpendicular to the optic axis value of the optical rotatory power. Our results correlate positively with previously measured data for KDP crystals.

Go to article

Authors and Affiliations

Y. Shopa
M. Shopa
N. Ftomyn
Download PDF Download RIS Download Bibtex

Abstract

This paper demonstrates the use of a zinc oxide (ZnO) thin film in a 1-μm ring laser cavity as a saturable absorber to successfully generate Q-switching pulses. The tunability of the laser pulses is achieved by integrating a tunable bandpass filter (TBPF) in an ytterbium-doped laser cavity that results in 9.4 nm of tuning range, which wavelength is from 1040.70 nm to 1050.1 nm. The peak energy in the pulse which is 1.47 nJ was measured together with a minimum pulse width of 2.4 μs. In addition, the repetition rate increases from 25.77 to 45.94 kHz as the pump power level being increased from 103.1 to 175.1 mW. The results obtained in this experiment demonstrated consistent results and stable throughout the experiment. Therefore, ZnO thin film is considered as a good candidate in 1-μm pulsed laser applications.

Go to article

Authors and Affiliations

R.A. Shaharuddin
S.A. Azzuhri
M.A. Ismail
F.A.A. Rashid
M.Z. Samion
M.Z.A. Razak
H. Ahmad
Download PDF Download RIS Download Bibtex

Abstract

In this work we discuss a method of preparation of a highly sensitive light detector based on ZnO nanorods. A photoresistor constructed by us is based on a heterojunction between high quality ZnO nanorods and high resistivity p-type Si used as a substrate for nanorods’ deposition. ZnO nanorods are grown by a modified version of a microwave assisted hydrothermal method which allows for growth of high quality ZnO nanorods in a few minutes. The obtained photoresistor responds to a wide spectral range of light starting from near infrared (IR) to ultraviolet (UV). Properties of the detector are evaluated. We propose the use of the detector as an optical switch.

Go to article

Authors and Affiliations

B.S. Witkowski
R. Pietruszka
S. Gieraltowska
L. Wachnicki
H. Przybylinska
M. Godlewski
Download PDF Download RIS Download Bibtex

Abstract

A deformation sensing technique with a multimode plastic optical fibre based on intensity speckle patterns’ correlation coefficient measurement has been presented. Influence of the average speckle size on results of deformation measuring has been studied and discussed. The presented sensing technique provides a good linear response to the applied deformation in a relatively wide operation region. It is shown that the proposed technique is highly sensitive, low-cost and simple to implement in practice.

Go to article

Authors and Affiliations

V. Varyshchuk
Y. Bobitski
H. Poisel
Download PDF Download RIS Download Bibtex

Abstract

This paper presents a 3D distance measurement accuracy improvement for stereo vision systems using optimization methods A Stereo Vision system is developed and tested to identify common uncertainty sources. As the optimization methods are used to train a neural network, the resulting equation can be implemented in real time stereo vision systems. Computational experiments and a comparative analysis are conducted to identify a training function with a minimal error performance for such method. The offered method provides a general purpose modelling technique, attending diverse problems that affect stereo vision systems. Finally, the proposed method is applied in the developed stereo vision system and a statistical analysis is performed to validate the obtained improvements.

Go to article

Authors and Affiliations

J.C. Rodríguez-Quiñonez
O. Sergiyenko
W. Flores-Fuentes
M. Rivas-lopez
D. Hernandez-Balbuena
R. Rascón
P. Mercorelli
Download PDF Download RIS Download Bibtex

Abstract

Many variants of thin film technology are nowadays part of the photovoltaic market. The most popular are amorphous silicon, CIS (Copper Indium Selenide)/CIGS (Copper Indium Gallium Selenide)/CIGSS (Copper Indium Gallium Sulphur Selenide), and CdS/CdTe (Cadmium Sulphide/Cadmium-Telluride) cells. All mentioned types allow potentially for a flexible cell structure. Most emitter contacts are currently based on TCOs (Transparent Conductive Oxides), however, wider approach with alternative carbon nanoforms, silver nanolayers and polymer materials, called TCLs (Transparent Conductive Layers) are also in use. Authors decided to investigate influence of mechanical stresses on physical and electrical behaviour of these layers. Consequently, the aim of work is to determine the level and possible mechanisms of flexible a-Si cell parameters degradation due to a deterioration of transparent contact properties.

Go to article

Authors and Affiliations

Maciej Sibiński
ORCID: ORCID
K. Znajdek
Download PDF Download RIS Download Bibtex

Abstract

The Ag8SnSe6 argyrodite compound was synthesized by the direct melting of the elementary Ag, Sn and Se high purity grade stoichiometric mixture in a sealed silica ampoule. The prepared polycrystalline material was characterized by the X-ray diffraction (XRD), visible (VIS) and near-infrared (NIR) reflection and photoluminescence (PL) spectroscopy. XRD showed that the Ag8SnSe6 crystallizes in orthorhombic structure, Pmn21 space group with lattice parameters: а = 7.89052(6) Å, b = 7.78976(6) Å, c = 11.02717(8) Å. Photoluminescence spectra of the Ag8SnSe6 polycrystalline wafer show two bands at 1675 nm and 1460 nm. Absorption edge position estimated from optical reflectance spectra is located in the 1413–1540 nm wavelength range.

Go to article

Authors and Affiliations

Ihor Semkiv
Hryhoriy Ilchuk
Marek Pawlowski
Viktor Kusnezh
Download PDF Download RIS Download Bibtex

Abstract

In this paper, triangular lattice index-guiding photonic crystal fibres (PCFs) are synthesized to compensate the chromatic dispersion of a single mode fibre (SMF-28) for an 80 km optical link operating at 1.55 μm, by using a directed tabu search algorithm. Hole-to-hole distance, circular air-hole diameter, solid-core diameter, ring number and PCF length parameters are optimized for this purpose. Three synthesized PCFs with different physical parameters are compared in terms of their objective functions values, residual dispersions, compensation ratios and confinement losses.

Go to article

Authors and Affiliations

Fethallah Karim
Download PDF Download RIS Download Bibtex

Abstract

In this paper we propose a new sliceable bandwidth variable transponder (SBVT) architecture with the separate analysis on the transmitter and receiver section. In transmission section we propose a distance module (DM) which is a programmable module. It divides a data stream/main stream (which employs a super-channel) into sub-stream and assigned modulation technique to each sub-stream based on their light path distance detailing the concept of sub-channel. In this paper, we have also proposed an algorithm for the distance module. Next we propose a modulation and transmission module (M&TM), where, planar light wave circuit (PLC) is used for enabling three modulation techniques (PM-16QAM, PM-QPSK and PM-BPSK). Finally, we propose the receiving section, which is designed to support three modulation techniques. It consists of two demodulator circuits, one for PM-16QAM/PM-QPSK and the other for PM-BPSK. In this proposed work, we focus on the multi-mode interference (MMI) devices (MMI coupler and MMI splitter) because of their photonic integration technology which is necessary for the implementation of SBVT. Lastly, we propose an elastic optical node architecture which removes the limitations of previously discussed node architecture for long distance communication.

Go to article

Authors and Affiliations

Ujjwal
T. Jaisingh

Instructions for authors

Guide for Authors

https://www.editorialsystem.com/opelre/journal/for_authors/

OPTO-ELECTRONICS REVIEW is an open access journal. This involves the payment of an article publishing charge (APC) by the authors, their institution or funding body. We make the article freely available immediately upon publication on PAS Jornals platform (https://journals.pan.pl/opelre)

Article publishing charge: the flat fee of 400 EUR (in PLN 1 750) per paper (see the above link with instructions for Authors for details)

Additional info

Opto-Electronics Review was established in 1992 for the publication of scientific papers concerning optoelectronics and photonics materials, system and signal processing. This journal covers the whole field of theory, experimental verification, techniques and instrumentation and brings together, within one journal, contributions from a wide range of disciplines. Papers covering novel topics extending the frontiers in optoelectronics and photonics are very encouraged. The main goal of this magazine is promotion of papers presented by European scientific teams, especially those submitted by important team from Central and Eastern Europe. However, contributions from other parts of the world are by no means excluded.

Articles are published in OPELRE in the following categories:

-invited reviews presenting the current state of the knowledge,

-specialized topics at the forefront of optoelectronics and photonics and their applications,

-refereed research contributions reporting on original scientific or technological achievements,

-conference papers printed in normal issues as invited or contributed papers.

Authors of review papers are encouraged to write articles of relevance to a wide readership including both those established in this field of research and non-specialists working in related areas. Papers considered as “letters” are not published in OPELRE.

Opto-Electronics Review is published quarterly as a journal of the Association of Polish Electrical Engineers (SEP) and Polish Academy of Sciences (PAS) in cooperation with the Military University of Technology and under the auspices of the Polish Optoelectronics Committee of SEP.

Abstracting and Indexing:

Arianta

BazTech

EBSCO relevant databases

EBSCO Discovery Service

SCOPUS relevant databases

ProQuest relevant databases

Clarivate Analytics relevant databases

WangFang

additionally:

ProQuesta (Ex Libris, Ulrich, Summon)

Google Scholar

Policies and ethics:

The editors of the journal place particular emphasis on compliance with the following principles:

Ethical policy of Opto-Electronics Review

The ethical policy of Opto-Electronics Review follows the European Code of Conduct for Research Integrity and is also guided by the core practices and policies outlined by the Committee on Publication Ethics (COPE).

Authors must be honest in presenting their results and conclusions of their research. Research misconduct is harmful for knowledge.

Research results

Fabrication, falsification, or selective reporting of data with the intent to mislead or deceive is unethical, as is the theft of data or research results from others. The results of research should be recorded and maintained to allow for analysis and review. Following publication, the data should be retained for a reasonable period and made available upon request. Exceptions may be appropriate in certain circumstances to preserve privacy, to assure patent protection, or for similar reasons.

Authorship

All those who have made a significant contribution should be given chance to be cited as authors. Other individuals who have contributed to the work should be acknowledged. Articles should include a full list of the current institutional affiliations of all authors, both academic and corporate.

Competing interests

All authors, referees and editors must declare any conflicting or competing interests relating to a given article. Competing interests through their potential influence on behavior or content or perception may undermine the objectivity, integrity, or perceived value of publication.

Peer Review

We are committed to prompt evaluation and publication of fully accepted papers in Opto-Electronics Review’s publications. To maintain a high-quality publication, all submissions undergo a rigorous review process.

Characteristics of the peer review process are as follows:

• Simultaneous submissions of the same manuscript to different journals will not be tolerated.

• Manuscripts with contents outside the scope will not be considered for review.

• Opto-Electronics Review is a single-blind review journal.

• Papers will be refereed by at least 2 experts as suggested by the editorial board.

• In addition, Editors will have the option of seeking additional reviews when needed. Authors will be informed when Editors decide further review is required.

• All publication decisions are made by the journal’s Editor-in-Chief based on the referees’ reports. Authors of papers that are not accepted are notified promptly.

• All submitted manuscripts are treated as confidential documents. We expect reviewers to treat manuscripts as confidential material.

• Editors and reviewers involved in the review process should disclose conflicts of interest resulting from direct competitive, collaborative, or other relationships with any of the authors, and remove oneself from cases in which such conflicts preclude an objective evaluation. Privileged information or ideas that are obtained through peer review must not be used for competitive gain.

• A reviewer should be alert to potential ethical issues in the paper and should bring these to the attention of the editor, including any substantial similarity or overlap between the manuscript under consideration and any other published paper of which the reviewer has personal knowledge. Any statement, observation, derivation, or argument that had been previously reported should be accompanied by the relevant citation.

• Personal criticism is inappropriate.

Plagiarism

Reproducing text from other papers without properly crediting the source (plagiarism) or producing many papers with almost the same content by the same authors (self-plagiarism) is not acceptable. Submitting the same results to more than one journal concurrently is unethical. Exceptions are the review articles. Authors may not present results obtained by others as if they were their own. Authors should acknowledge the work of others used in their research and cite publications that have influenced the direction and course of their study.

Plagiarism is not tolerated. All manuscripts submitted to Opto-Electronics Review will be checked for plagiarism (copying text or results from other sources) and self-plagiarism (duplicating substantial parts of authors’ own published work without giving the appropriate references) using the CrossCheck database (iThenticate plagiarism checker).

Duplicate submission

Simultaneous submissions of the same manuscript to different journals will not be tolerated. The submitted article will be removed without consideration.

Corrections and retractions

All authors have an obligation to inform and cooperate with journal editors to provide prompt retractions or correction of errors in published works.

• The journal will issue retractions if:

• There is clear evidence that the findings are unreliable, either as a result of misconduct (e.g., data fabrication or honest error - miscalculation or experimental error);

• The findings have previously been published elsewhere without proper cross-referencing, permission or justification (i.e., cases of redundant publication);

• It constitutes plagiarism;

• It reports unethical research.

• The journal will issue errata, if:

• A small portion of an otherwise reliable publication proves to be misleading (especially because of honest error);

• The author list is incorrect.

Other forms of misconduct include failure to meet clear ethical and legal requirements such as misrepresentation of interests, breach of confidentiality, lack of informed consent and abuse of research subjects or materials. Misconduct also includes improper dealing with infringements, such as attempts to cover up misconduct and reprisals on whistleblowers.

The primary responsibility for handling research misconduct is in the hands of those who employ the researchers. If a possible misconduct is brought to our attention, we will seek advice from the referees and the Editorial Board. If there is the evidence, we will resolve the matter by appropriate corrections in the printed and online journal; by refusing to consider an author's future work and by contacting affected authors and editors of other journals.

Human and Animal Rights

If the work involves the use of human subjects, the author should ensure that the work described has been carried out in accordance with The Code of Ethics of the World Medical Association (Declaration of Helsinki) for experiments involving humans; Uniform Requirements for manuscripts submitted to Biomedical journals. Authors should include a statement in the manuscript that informed consent was obtained for experimentation with human subjects. The privacy rights of human subjects must always be observed.

All animal experiments should comply with the ARRIVE guidelines and should be carried out in accordance with the EU Directive 2010/63/EU for animal experiments, and the authors should clearly indicate in the manuscript that such guidelines have been followed.

This page uses 'cookies'. Learn more