Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 3
items per page: 25 50 75
Sort by:
Download PDF Download RIS Download Bibtex

Abstract

The study examined the impact of the angle of incidence of mechanical waves on various types of quasi one-dimensional superlattice. Binary periodic structure, quasi-periodic distribution of Thue-Morse layers and Severin’s aperiodic multilayer were used. Using the concatenation and recursive rules, the distribution of layers was determined for individual structure types for generation numbers equal to 3, 4 and 5. The structures were selected so that the thickness of the composite was the same for each type of distribution for a given generation number value. Transfer Matrix Method algorithm was used to determine reflectance. The band structure of reflectance has been demonstrated for incidence angles up to 90 degrees at mechanical wave frequencies up to 50 kHz. The existence of wide bands of high reflectance above the acoustic frequencies was demonstrated for the analyzed structures. Increasing the layer thickness caused an inhomogeneous shifts of transmission peaks towards lower frequencies.
Go to article

Authors and Affiliations

S. Garus
1
ORCID: ORCID
W. Sochacki
1
ORCID: ORCID

  1. Czestochowa University of Technology, Department of Mechanics and Fundamentals of Machinery Design, Faculty of Mechanical Engineering and Computer Science, 73 Dąbrowskiego Str., 42-201 Częstochowa, Poland
Download PDF Download RIS Download Bibtex

Abstract

The paper presents the results of tests on dynamic stability of Bernoulli-Euler beam with damages. Damages (cracks) were modeled using three rotational springs. An analysis of the influence of crack depth and their position relative to the beam ends on dynamic stability of the beam was carried out. The problem of dynamic stability was solved by applying the mode summation method. Applying an orthogonal condition of eigenfunctions, the dynamic of the system was described with the use of the Mathieu equation. The obtained equation allowed the dynamic stability of the tested system to be analyzed. Stable and unstable solutions were analyzed using the Strutt card.
Go to article

Authors and Affiliations

W. Sochacki
1
ORCID: ORCID
S. Garus
1
ORCID: ORCID
J. Garus
1
ORCID: ORCID

  1. Czestochowa University of Technology, Department of Mechanics and Fundamentals of Machinery Design, Faculty of Mechanical Engineering and Computer Science, 73 Dąbrowskiego Str., 42-201 Częstochowa, Poland
Download PDF Download RIS Download Bibtex

Abstract

This work concerns the study of the coatings for the ultrasound frequency range as a quasi one-dimensional phononic crystal structure protecting a sea object against high resolution active sonar in the frequency range most commonly found for this type of equipment. The topology of the examined structure was optimized to obtain a band gap in the 2.2-2.3 MHz frequency band. For this purpose, a genetic algorithm was used, which allows for optimal distribution of individual elements of the ultrasound multilayer composite. By optimal distribution is meant to achieve a structure that will allow minimal reflectance in a given frequency range without height reflectance peaks with a small half width. Analysis of the wave propagation was made using the Transfer Matrix Method (TMM). As part of the research, 15 and 20-layer structures with reflectance at the level of 0.23% and 0.18%, respectively, were obtained. Increasing the number of layers in the analyzed structures resulted in finding such a distribution in which a narrow band of low reflectance was obtained, such distributions could also be used as bandpass filters. The use of a genetic algorithm for designing allows to obtain modern coatings, the characteristics of which result from the structure.
Go to article

Authors and Affiliations

S. Garus
1
ORCID: ORCID
W. Sochacki
1
ORCID: ORCID
J. Garus
1
ORCID: ORCID
A.V. Sandu
2
ORCID: ORCID

  1. Czestochowa University of Technology, Department of Mechanics and Fundamentals of Machinery Design, Faculty of Mechanical Engineering and Computer Science, 73 Dąbrowskiego Str., 42-201 Częstochowa, Poland
  2. Gheorghe Asachi Technical University of Iasi, Faculty of Materials Science and Engineering, Blv d. D. Mangeron 71, 700050 lasi, Romania

This page uses 'cookies'. Learn more