In recent years, GaN-based light-emitting diode (LED) has been widely used in various applications, such as RGB lighting system, full-colour display and visible-light communication. However, the internal quantum efficiency (IQE) of green LEDs is significantly lower than that of other visible spectrum LED. This phenomenon is called “green gap”. This paper briefly describes the physical mechanism of the low IQE for InGaN/GaN multiple quantum well (MQW) green LED at first. The IQE of green LED is limited by the defects and the internal electric field in MQW. Subsequently, we discuss the recent progress in improving the IQE of green LED in detail. These strategies can be divided into two categories. Some of these methods were proposed to enhance crystal quality of InGaN/GaN MQW with high In composition and low density of defects by modifying the growth conditions. Other methods focused on increasing electron-hole wave function overlap by eliminating the polarization effect.
All normal dispersion (ANDi) and highly nonlinear chalcogenide glass photonic crystal fiber (PCF) is proposed and numerically investigated for a broad, coherent and ultra-flat mid-infrared supercontinuum generation. The proposed PCF consists of a solid core made of Ga8Sb32S60 glass surrounded by seven rings of air holes arranged in a triangular lattice. We show by employing the finite difference frequency domain (FDFD) method that the Ga8Sb32S60 PCF dispersion properties can be engineered by carefully adjusting the air holes diameter in the cladding region and ANDi regime is achieved over the entire range of wavelengths with a zero chromatic dispersion around 4.5 μm. Moreover, we demonstrate that injecting 50 fs width and 20 kW peak power laser pulses (corresponding to a pulse energy of 1.06 nJ) at a pump wavelength of 4.5 μm into a 1 cm long ANDi Ga8Sb32S60 PCF generates a broad, flat-top and perfectly coherent SC spectrum extending from 1.65 μm to 9.24 μm at the 20 dB spectral flatness. These results make the proposed Ga8Sb32S60 PCF an excellent candidate for various important mid-infrared region applications including mid-infrared spectroscopy, medical imaging, optical coherence tomography and materials characterization.
The head loss is a decrease in compressive height caused by friction and direction changes of flow at the sliced bend. This method expected to provide is easy, fast, and economical. The elements of influence are the velocity of flow, the num-ber of slices, average length of sliced walls, angle changes of the sliced, coefficient of friction, acceleration of gravity, and slope of the pipe. Equation for coefficient of head loss (Kb) is an analysis method for the head loss (hL) calculation. The analysis results that have obtained are the larger diameter of the pipe, and the more slices with a fixed discharge, the coefficient of hL becomes small. Conversely, if the diameter of the pipe is getting smaller, and the slice is getting less, then the coefficient of hL becomes bigger. This method, expected to give new knowledge in pipeline network applications, especially for the large diameter of pipelines.
River training structures; such as submerged groynes are low profile linear structures that are generally located on the outside bank to form groynes fields and prevent the erosion of stream banks by keeping a flow away from it. In the present research, the maximum scour depth was measured based on laboratory experiments where different shapes of submerged groynes (I-shape, L-shape, T-shape) were used as sort of countermeasures to investigate about most shapes that reduce the scour around them. The result of submerged groynes showed a clear decrease in scour depth ratio due to increasing sub-merged ratio and increase the scour hole geometry with increasing of flow intensity, and also Froude number. The maxi-mum scour hole in this research was observed at T-shape groyne and then followed by I-shape groyne and L-shape groyne. The maximum scour depth that cased by I-shape was more than L-shape by a percentage about 8.2%, and it was less than T-shape by a percentage about 16.4%.
The purpose of this study is to find the value of the discharge coefficient (Cd) on a sieve with a circular perforated plate so that it can be used for application in the field. The method used is to make a physical model test of the screen weir in the laboratory with a width of 40 cm and a length of 797 cm, then the screen is made variations in the diameter of the hole 6, 8, 10 and 12 mm, flowrate Q = 453–4 481 cm3∙s–1 and the slope of the screen θ = 20–45°. The result was quite ef-fective, the sediment did not enter above the screen and did not clog the screen even the catch was quite good about 80% of the screen rods. The discharge coefficient (Cd) is directly proportional to the square value of the number Froude (Fr), the slope of the screen (θ) and the ratio of distance, diameter of the screen (a:d) and inversely proportional to the value of the specific energy square (E). From modelling the average value of the discharge coefficient (Cd) between 0.1–2.75 with NSE = 0.71, MAE = 0 and RMSE = 0.12.