The paper presents modeling and simulation results of the operation of a three-phase fluidized bed bioreactorwith partial recirculation of biomass. The proposed quantitative description of the bioreactor takes into account biomass growth on inert carriers, microorganisms decay and interphase biomass transfer. Stationary characteristics of the bioreactor and local stability of steady-stateswere determined. The influence of microbiological growth kinetics on the multiplicity of steady-states was discussed. The relationship between biofilm growth and boundaries of fluidized bed existence was shown.
Exergy analysis of low temperature geothermal heat plant with compressor and absorption heat pump was carried out. In these two concepts heat pumps are using geothermal water at 19.5°C with spontaneous outflow 24 m3/h as a heat source. The research compares exergy efficiency and exergy destruction of considered systems and its components as well. For the purpose of analysis, the heating system was divided into five components: geothermal heat exchanger, heat pump, heat distribution, heat exchanger and electricity production and transportation. For considered systems the primary exergy consumption from renewable and non-renewable sources was estimated. The analysis was carried out for heat network temperature at 50/40°C, and the quality regulation was assumed. The results of exergy analysis of the system with electrical and absorption heat pump show that exergy destruction during the whole heating season is lower for the system with electrical heat pump. The exergy efficiencies of total system are 12.8% and 11.2% for the system with electrical heat pump and absorption heat pump, respectively.
This paper describes experiments on the application of sodium bicarbonate desulphurisation in the coal-fuel boiler. The boiler has been in operation for several years now and it has refiably fulfilled the original assignment to reduce SO2 emissions from the value of 1200 - 1500 mg/Nm3 to 400 mg/Nm3. Higher desulphurisation efficiency is determined only by the ratio of Na/S sorbent dosage. The resulting product of desulphurisation is stored together with fly ash in underground mines, and has no influence on the groundwater. Positive experience of the tests and boiler operation lies in higher reactivity of sodium and sulphur as compared with conventional methods based on limestone. Within the scope of the secondary measures of elimination of sulphur oxides in combustion products, an experimental dry-method desulphurisation of combustion products was performed by blasting an agent containing sodium bicarbonate NaHCO3 (99.6 %) into the flue ways before the electrostatic precipitator in a coal-fuel furnace with the steam output of 220 t/h.
Improvements of modern manufacturing techniques implies more efficient production but also new challenges for coordinate metrologists. The crucial task here is a coordinate measurement accuracy assessment. It is important because according to technological requirements, measurements are useful only when they are stated with their accuracy. Currently used methods for the measurements accuracy estimation are difficult to implement and time consuming. It is therefore important to implement correct and validated methods that will also be easy to implement. The method presented in this paper is one of them. It is an on-line accuracy estimation method based on the virtual CMM idea. A model is built using a modern LaserTracer system and a common test sphere and its implementation lasts less than one day. Results obtained using the presented method are comparable to results of commonly used uncertainty estimation methods which proves its correct functioning. Its properties predispose it to be widely used both in laboratory and industrial conditions.
ARGUMENTUM
In ecclesia Calvinistarum sita Caioduni, quod est oppidum Lithuaniae, invenitur inscriptio celebrans memoriam Adami Freytag Thoruniensis (1608–1650), auctoris libri, cui titulus est Architectura militaris nova et aucta. Hic editur inscriptio et narratur de ipso Adamo Freytag.
After moving to Italy in 1856, Teofil Lenartowicz, inspired by the great Italian art and supported by the best Florentine artists of the time Giovanni Dupré and Enrico Pazzi, began studying sculpture. Lenartowicz’s sculptures were always connected with literature: his work shows howone influenced the other. It is no accident that his style as a sculptor has been called ‘poetic’ by the critics. The Polish immigrant was fascinated by the Italian Renaissance, and especially by the art of Lorenzo Ghiberti. At the same time, he never forgot about Polish folklore, which played a significant role in his artistic vision. One of the most impressive examples of this intersection of influences is the bas-relief The Holy Workers, complemented by a poem bearing the same name.