The article presents tests results of metalforming of magnesium alloy AZ61. Materials for tests were ingots sized  40×90 mm from magnesium alloy marked with symbol AZ61. Before the shaping process the ingots underwent heat treatment. As a result of conduction of the deformation processes there were rods achieved with diameter of 8 mm. There were axisymmetrical compression tests conducted on the samples taken from rods in temperature range from RT to 350ºC in order to determine the plasticity and formability of the alloy AZ61. Static tensile test was conducted in room temperature (RT), in 300ºC and in 350ºC. With the use of light and electron microscopy techniques the changes which occurred in the microstructure of AZ61alloy in initial condition and after plastic deformation (classic extrusion, KoBo method extrusion) were described. The deformation of alloy AZ61 using the KoBo method contributes to an increase in strength and plastic properties. The effect of superplastic flow was found at a temperature of 350ºC, where a 300% increase in plastic properties – elongation value was obtained. The analysis of the microstructure showed a significant grain size reduction in the microstructure of alloy AZ61 after deformation by the KoBo method and after an axisymmetric compression test, where grains of an average diameter of d = 13 µm were obtained.

The article presents results of tests performed at the AGH-University of Science and Technology in Cracow on strength of single-coil inductors used as tools in electrodynamic machining of pipes. The character of volumetric Lorentz forces acting on coils of compressing and expanding inductors was discussed, and numerically determined distributions of stresses and displacements created in coils under the impact of these forces were presented. The problems presented are relevant when designing durable inductors intended for industrial applications.

The article deals with the contemporary translation of Tadeusz Różewicz’s poems into Russian. Regardless of the fact that some of his poetry had already been translated and published, new times and new readers need new translations. The considerations presented in the article refer precisely to them. Taken into account were primarily the translations of a generation of contemporary translators for an international competition on the translation of Różewicz’s poems, announced in 2013 by the foundation ‘For your freedom and ours’. The translations of three poems by the Polish poet have been considered: Words, In the light of flickering lamps and Such is the master, works frequently chosen by the winners of the said competition. In particular the analysis regards the saturation of the poems with cultural realities and inter-textual elements. Therefore, comments and some translators’ notes accompanying the translations were taken into account, ones defining their approach to the translation and the translated text itself. The considerations confirmed the need to activate the cognitive function of translation in modern translations – the purpose of the mentioned comments – but also to pay attention to the problems of translating free verse into Russian.

This research paper shows the influence of a repeated SPD (Severe Plastic Deformation) plastic forming with the DRECE technique (Dual Rolls Equal Channel Extrusion) on hardening of low carbon IF steel. The influence of number of passes through the device on change of mechanical properties, such as tensile strength TS and yield stress YS, of tested steel was tested. The developed method is based on equal channel extrusion with dual rolls and uses a repeated plastic forming to refinement of structure and improve mechanical properties of metal bands [1-2]. For the tested steel the increase of strength properties after the DRECE process was confirmed after the first pass in relation to the initial material. The biggest strain hardening is observed after the fourth pass.

The article presents tests results of the influence of deformation methods on the microstructure and properties of alloy WE43. There were direct extrusion tests and extrusion with KoBo method performed. An assessment of the influence of the methods of deformation on the microstructure and the mechanical properties of the achieved rods from alloy WE43 was conducted. There was an analysis of microstructure carried out with the use of light and scanning microscopy techniques in the initial state and after plastic deformation. Static tensile test was conducted in temperature of 350°C at a speed of 0.0001 m·s–1 and microhardness measurements were performed of HV0.2. On the basis of the achieved mechanical tests results it was stated that in the temperature of 350°C for samples deformed with the use of KoBo method there was an effect of superplastic flow found. The value of elongation achieved was 250% which was 3 times higher than in case of classic extrusion (80%).

The paper presents a multi-scale mathematical model dedicated to a comprehensive simulation of resistance heating combined with the melting and controlled cooling of steel samples. Experiments in order to verify the formulated numerical model were performed using a Gleeble 3800 thermo-mechanical simulator. The model for the macro scale was based upon the solution of Fourier-Kirchhoff equation as regards predicting the distribution of temperature fields within the volume of the sample. The macro scale solution is complemented by a functional model generating voluminal heat sources, resulting from the electric current flowing through the sample. The model for the micro-scale, concerning the grain growth simulation, is based upon the probabilistic Monte Carlo algorithm, and on the minimization of the system energy. The model takes into account the forming mushy zone, where grains degrade at the melting stage – it is a unique feature of the micro-solution. The solution domains are coupled by the interpolation of node temperatures of the finite element mesh (the macro model) onto the Monte Carlo cells (micro model). The paper is complemented with examples of resistance heating results and macro- and micro-structural tests, along with test computations concerning the estimation of the range of zones with diverse dynamics of grain growth.

The paper presents the results of tests concerning the effect of the extrusion process in the complex strain state on the microstructure and properties of one of magnesium alloy with aluminium, zinc and manganese, designated AZ61. Due to its specific gravity, it is increasingly being used in the automotive and aerospace industries to reduce the weight of structural elements. As a result of plastic deformation processes, rods with a diameter of 8, 6 and 4 mm were obtained from AZ61 magnesium alloy. The microstructure analysis was performed using light and electron microscopy (STEM) techniques in the initial state and after plastic deformation. Microstructure studies were supplemented with a quantitative analysis using the Metilo program. A number of stereological parameters were determined: average diameter of grain, shape factor. A static tensile test was carried out at 250ºC and 300ºC, at deformation rates of 0.01, 0.001 and 0.0001 m·s–1. Better plastic properties after deformation using KoBo method were obtained than with conventional extrusion.

This article is a description of the progress of research and development in the area of massive large-scale castings - slag ladles implemented in cooperation with the Faculty of Foundry Engineering of UST in Krakow. Slag ladles are the one of the major castings that has been developed by the Krakodlew (massive castings foundry) for many years. Quality requirements are constantly increasing in relation to the slag ladles. Slag ladles are an integral tool in the logistics of enterprises in the metallurgical industry in the process of well-organized slag management and other by-products and input materials. The need to increase the volume of slag ladles is still growing. Metallurgical production is expected to be achieved in Poland by 2022 at the level of 9.4 million Mg/year for the baseline scenario - 2016 - 9 million Mg/year. This article describes the research work carried out to date in the field of technology for the production of massive slag ladles of ductile cast iron and cast steel.