The article presents an analysis of the multi-operation hot die forging process, performed on a press, of producing a lever forging used in the motorcycles of a renowned producer by means of numerical simulations. The investigations were carried out in order to improve (perfect) the currently applied production technology, mainly due to the presence of forging defects during the industrial production process. The defects result mainly from the complicated shape of the forging (bent main axis, deep and thin protrusions, high surface diversity in the cross section along the length of the detail), which, during the filling of the die by the deformed material, causes the presence of laps, wraps and underfills on the forging. Through the determination of the key parameters/quantities during the forging process, which are difficult to establish directly during the industrial process or experimentally, a detailed and complex analysis was performed with the use of FEM as well as through microstructure examinations. The results of the performed numerical modelling made it possible to determine: the manner of the material flow and the correctness of the impression filling, as well as the distributions of temperature fields and plastic deformations in the forging, and also to detect the forging defects often observed in the industrial process. On this basis, changes into the process were introduced, making it possible to improve the currently realized technology and obtain forgings of the proper quality as well as shape and dimensions.
The paper presents a prototype semi-industrial cooling line developed by the authors, which makes it possible to design a thermal treatment of forgings with the use of the forging heat, together with exemplary test results for forgings forked type. The proposed method of heat treatment dedicated to these forgings was described and compared to traditionally used heat treatment method in chamber furnaces. Next, the original research stand was presented, which performs mechanical fatigue test on final products – forked-type forgings. Forgings after heat treatment and cooling on the prototype line were tested on this stand in condition of cyclically variable mechanical loads in order to resistance to mechanical fatigue was analyzed and the influence of performed exemplary heat treatment on mechanical properties. The presented preliminary investigations performed on the designed combined research standing, consisting of: the prototype controlled cooling line, as well as mechanical fatigue stand point to the possibility of implementing thermal treatment with the use of the heat generated during the forging process and determining its impact on the mechanical properties of forgings.
The study presents a durability analysis of dies used in the first operation of producing a valve-type forging from high nickel steel assigned to be applied in motor truck engines. The analyzed process of producing exhaust valves is realized in the forward extrusion technology and next through forging in closed dies. It is difficult to master, mainly due to the increased adhesion of the charge material (high nickel steel) to the tool’s substrate. The mean durability of tools made of tool steel W360, subjected to thermal treatment and nitriding, equals about 1000 forgings. In order to perform a thorough analysis, complex investigations were carried out, which included: a macroscopic analysis combined with laser scanning, numerical modelling by FEM, microstructural tests on a scanning electron microscopy and light microscopy (metallographic), as well as hardness tests. The preliminary results showed the presence of traces of abrasive wear, fatigue cracks as well as traces of adhesive wear and plastic deformation on the surface of the dies. Also, the effect of the forging material being stuck to the tool surface was observed, caused by the excessive friction in the forging’s contact with the tool and the presence of intermetallic phases in the nickel-chromium steel. The obtained results demonstrated numerous tool cracks, excessive friction, especially in the area of sectional reduction, as well as sticking of the forging material, which, with insufficient control of the tribological conditions, may be the cause of premature wear of the dies.
This article discusses the results of studies using the developed artificial neural networks in the analysis of the occurrence of the four main mechanisms destroying the selected forging tools subjected to five different surface treatment variants (nitrided layer, pad welded layer and three hybrid layers, i.e. AlCrTiSiN, Cr/CrN and Cr/AlCrTiN). Knowledge of the forging tool durability, needed in the process of artificial neural network training, was included in the set of training data (about 800 records) derived from long-term comprehensive research carried out under industrial conditions. Based on this set, neural networks with different architectures were developed and the results concerning the intensity of the occurrence of thermal-mechanical fatigue, abrasive wear, mechanical fatigue and plastic deformation were generated for each type of the applied treatment relative to the number of forgings, pressure, friction path and temperature.
The paper covers the research on the process of solutionizing of 7075 aluminum alloy in cold tools during the stamping of a high-strength structural element (B-pillar’s base). For technological reasons, in order to obtain high strength parameters of the 7075 alloy, it is necessary to carry out a solutionization process, which allows to obtain dispersion strengthening during ageing process. Properly performed heat treatment of the alloy increases the strength of the material to approx. 600 MPa. The combination of the process of solutionization with simultaneous shaping is aimed at improving and simplifying technological operations of aluminum alloy stamping, shortening the duration of the manufacturing process and reducing production costs. The manufactured lower part of the B-pillar will be used for the verification of the validity of the developed method. During the experiment, a series of stamping tests were carried out, in which the lubricants, pressure and position of the upper and lower blankholders were the variables. The obtained results allow to estimate the influence of the cooling conditions on the strength of the drawpieces obtained after the process of artificial ageing. In order to verify and analyse the results more quickly, a numerical simulation was carried out.