Modernization of lands and buildings register, which is run in Poland now, assumes capturing boundaries location data by various methods. They are: direct measurement preceded by determining of boundaries in the presence of parties, photogram- metric method, cartographic method, using existing maps being in analogue form. These methods not always assure accuracy. In the paper, an idea of correcting of location of boundary points which do not fulfil accuracy requirements has been presented. These corrections have been computed by assumption of invariability of parcel area revealed in register, so far. Such way of operation from one side would avoid many misunderstandings and difficulties by applying data collected in cadastre and from the other side will not disturb used procedures, which aim is to determine boundary of parcels with demanded accuracy.

Increasing demands on the utility properties of materials used for castings have led to the production of cast iron with a modified shape of graphite, where the required properties are achieved by a change in graphite shape, its size and layout, and a change in the basic structure of the metal. This paper is focused on the continuous method of producing spheroidal graphite FLOTRET. In the introductory section is summarized the theoretical foundations of the secondary treatment of cast irons, especially the FLOTRET flow method, describes the advantages and disadvantages of the method. The practical part is divided into laboratory and operational tests. Laboratory experiments were conducted on a laboratory-type modifier FLOTRET chamber, which was designed and hydraulically optimized. Experiments were focused on the effects of pressure altitude and amount of modifier on the residual values of magnesium, as conditions for a successful modification. The method was tested in two foundries under operating conditions and in one of them was observed a long-term modification process.

This paper presents the results of the theoretical and practical analysis of selected features of the function of conditional average value of the absolute value of delayed signal (CAAV). The results obtained with the CAAV method have been compared with the results obtained by method of cross correlation (CCF), which is often used at the measurements of random signal time delay. The paper is divided into five sections. The first is devoted to a short introduction to the subject of the paper. The model of measured stochastic signals is described in Section 2. The fundamentals of time delay estimation using CCF and CAAV are presented in Section 3. The standard deviations of both functions in their extreme points are evaluated and compared. The results of experimental investigations are discussed in Section 4. Computer simulations were used to evaluate the performance of the CAAV and CCF methods. The signal and the noise were Gaussian random variables, produced by a pseudorandom noise generator. The experimental standard deviations of both functions for the chosen signal to noise ratio (SNR) were obtained and compared. All simulation results were averaged for 1000 independent runs. It should be noted that the experimental results were close to the theoretical values. The conclusions and final remarks were included in Section 5. The authors conclude that the CAAV method described in this paper has less standard deviation in the extreme point than CCF and can be applied to time delay measurement of random signals.

The correlation of data contained in a series of signal sample values makes the estimation of the statistical characteristics describing such a random sample difficult. The positive correlation of data increases the arithmetic mean variance in relation to the series of uncorrelated results. If the normalized autocorrelation function of the positively correlated observations and their variance are known, then the effect of the correlation can be taken into consideration in the estimation process computationally. A significant hindrance to the assessment of the estimation process appears when the autocorrelation function is unknown. This study describes an application of the conditional averaging of the positively correlated data with the Gaussian distribution for the assessment of the correlation of an observation series, and the determination of the standard uncertainty of the arithmetic mean. The method presented here can be particularly useful for high values of correlation (when the value of the normalized autocorrelation function is higher than 0.5), and for the number of data higher than 50. In the paper the results of theoretical research are presented, as well as those of the selected experiments of the processing and analysis of physical signals.

Hybrid Renewable Energy Systems connected to the traditional power suppliers are an interesting technological solution in the field of energy engineering and the integration of renewable systems with other energy systems can significantly increase in energy reliability. In this paper, an analysis and optimization of the hybrid energy system, which uses photovoltaic modules and wind turbines components connected to the grid, is presented. The system components are optimized using two objectives criteria: economic and environmental. The optimization has been performed based on the experimental data acquired for the whole year. Results showed the optimal configuration for the hybrid system based on economical objective, that presents the best compromise between the number of components and total efficiency. This achieved the lowest cost of energy but with relatively high CO2 emissions, while environmental objective results with lower CO2 emissions and higher cost of energy and presents the best compromise between the number of components and system net present cost. It has been shown that a hybrid system can be optimized in such a way that CO2 emission is maximally reduced and – separately – in terms of reducing the cost. However, the study shows that these two criteria cannot be optimized at the same time. Reducing the system cost increase CO2 emission and enhancing ecological effect makes the system cost larger. However, depends on strategies, a balance between different optimization criteria can be found. Regardless of the strategy used economic criteria – which also indirect takes environmental aspects as a cost of penalties – should be considered as a major criterion of optimization while the other objectives including environmental objectives are less important.

Autocorrelation of signals and measurement data makes it difficult to estimate their statistical characteristics. However, the scope of usefulness of autocorrelation functions for statistical description of signal relation is narrowed down to linear processing models. The use of the conditional expected value opens new possibilities in the description of interdependence of stochastic signals for linear and non-linear models. It is described with relatively simple mathematical models with corresponding simple algorithms of their practical implementation.

The paper presents a practical model of exponential autocorrelation of measurement data and a theoretical analysis of its impact on the process of conditional averaging of data. Optimization conditions of the process were determined to decrease the variance of a characteristic of the conditional expected value. The obtained theoretical relations were compared with some examples of the experimental results.

Liquid-gas flows in pipelines appear in many industrial processes, e.g. in the nuclear, mining, and oil industry. The gamma-absorption technique is one of the methods that can be successfully applied to study such flows. This paper presents the use of the gamma-absorption method to determine the water-air flow parameters in a horizontal pipeline. Three flow types were studied in this work: plug, transitional plug-bubble, and bubble one. In the research, a radiometric set consisting of two Am-241 sources and two NaI(TI) scintillation detectors have been applied. Based on the analysis of the signals from both scintillation detectors, the gas phase velocity was calculated using the cross-correlation method (CCM). The signal from one detector was used to determine the void fraction and to recognise the flow regime. In the latter case, a Multi-Layer Perceptron-type artificial neural network (ANN) was applied. To reduce the number of signal features, the principal component analysis (PCA) was used. The expanded uncertainties of gas velocity and void fraction obtained for the flow types studied in this paper did not exceed 4.3% and 7.4% respectively. All three types of analyzed flows were recognised with 100% accuracy. Results of the experiments confirm the usefulness of the gamma-ray absorption method in combination with radiometric signal analysis by CCM and ANN with PCA for comprehensive analysis of liquid-gas flow in the pipeline.