Nano-sized yttria (Y2O3) powders were synthesized by a polymer solution route using polyvinyl alcohol (PVA) as an organic carrier. The PVA polymer affected the dispersion of yttrium ions in precursor sol. In this study, three kinds of PVA polymer (different molecular weight) were applied for synthesis of yttria powder. The PVA type as well as calcination temperature had a strongly influence on the particle morphology. Single crystal nano wire particles were observed at the temperature of polymer burn out range and the size was dependent on the PVA type. The stable, fully crystallized yttria powder was obtained through the calcination at 800°C for 1 h. The yttria powder prepared with the high weight PVA (MW: 153,000) revealed a particle size of 30 nm with a surface area of 18.8 m2/g.

The mechanical behavior and the change of retained austenite of nanocrystalline Fe-Ni alloy have been investigated by considering the effect of various Ni addition amount. The nanocrystalline Fe-Ni alloy samples were rapidly fabricated by spark plasma sintering (SPS). The SPS is a well-known effective sintering process with an extremely short densification time not only to reach a theoretical density value but also to prevent a grain growth, which could result in a nanocrystalline structures. The effect of Ni addition on the compressive stress-strain behavior was analyzed. The variation of the volume fraction of retained austenite due to deformation was quantitatively measured by means of x-ray diffraction and microscope analyses. The strain-induced martensite transformation was observed in Fe-Ni alloy. The different amount of Ni influenced the rate of the strain-induced martensite transformation kinetics and resulted in the change of the work hardening during the compressive deformation.

The effect of additives on the densification behavior and mechanical properties of pure and additive (Zr, B and Mg)-added silica ceramics were investigated for their application to the matrix phase of a silica fiber reinforced silica (SiO2/SiO2f) composite. The additives affected the rate of densification and crystallization (or transformation) of the amorphous silica. Among the compositions, pure silica ceramics sintered at 900°C for 1 h showed the maximum flexural strength. Based on the results, SiO2/SiO2f was fabricated by a repeated vacuum-assisted infiltration method followed by the heat treatment at 900°C for 1 h. The relative density of the composite was 78.2% with a flexural strength of 22.4 MPa. Fractography revealed that the composite was damaged by strong bonding at the fiber/matrix interface and the fracture of fiber.

The presence of lipopolysaccharide (LPS) in blood induces an inflammatory response which leads to multiple organ dysfunction and numerous metabolic disorders. Uncontrolled, improper or late intervention may lead to tissue hypoxia, anaerobic glycolysis and a disturbance in the acid -base balance. The effects of LPS-induced toxemia on biological and immunological markers were well studied. However, parameters such as base excess, ions, and acid-base balance were not fully investigated. Therefore, the objective of this study was to examine these blood parameters collectively in LPS-induced inflammatory toxemia in rat’s model. After induction of toxemia by injecting LPS at a rate of 5 mg/kg body weight intravenously, blood was collected from the tail vein of twenty rats and immediately analyzed. After 24 hours, the animals were sacrificed and the blood was collected from the caudal vena cava. The results revealed that the levels of pH, bicarbonate, partial pressure of oxygen, oxygen saturation, Alveolar oxygen, hemoglobin, hematocrit, magnesium (Mg2+), and calcium (Ca2+) were significantly decreased. On the other side, the levels of Base excess blood, Base excess extracellular fluid, partial pressure of carbon dioxide, lactate, Ca2+/Mg2+, potassium, and chloride were significantly increased compared to those found pre toxemia induction. However, sodium level showed no significant change. In conclusion, Acute LPS-toxemia model disturbs acid-base balance, blood gases, and ions. These parameters can be used to monitor human and animal toxemic inflammatory response induced by bacterial LPS conditions to assist in the management of the diagnosed cases.