In this study, the effect of the emergence angle of a source array on acoustic transmission in a typical shallow sea is simulated and analyzed. The formula we derived for the received signal based on the Normal Mode indicates that the signal is determined by the beamform on the modes of all sources and the samplings of all modes at the receiving depth. Two characteristics of the optimal emergence angle (OEA) are obtained and explained utilizing the aforementioned derived formula. The observed distributions of transmission loss (TL) for different sources and receivers are consistent with the obtained characteristics. The results of this study are valuable for the development and design of active sonar detection.

The present study thoroughly evaluated the effect of hydroxypropyl-β-cyclodextrin (HP-β-CD) on eluting of Aroclor1242 (one kind of PCBs (polychlorinated biphenyls)) from contaminated soil. The factors that might affect eluting efficiency including HP-β-CD concentration, contact time, eluting cycles, temperature, pH, salt content, humic acid, and ultrasonic were all tested to evaluate the PCBs eluting efficiency by HP-β-CD. Results indicated that Aroclor1242 can be eluted effectively from soil by HP-β-CD solution, 81% of Aroclor1242 was eluted from soil by 50 g/L of HP-β-CD solution after three cycles eluting, and the eluting efficiency was improved by increasing temperature and with ultrasonic. Furthermore, it was shown that the humic acid and extreme acidic/alkaline condition both decreased the eluting efficiency. In addition, column eluting experiment was conducted to simulate the practical HP-β-CD eluting of Aroclor1242 from contaminated soil, 18% of the PCBs was eluted from the soil column by 10 g/L of HP-β-CD. Overall, the results indicated the high extract power of HP-β-CD toward PCBs polluted soil and potential use of HP-β-CD for in situ remediation of PCBs contaminated soils.

The normal modes cannot be extracted even in the Pekeris waveguide when the source-receiver distance is very close. This paper introduces a normal mode extraction method based on a dedispersion transform (DDT) to solve this problem. The method presented here takes advantage of DDT, which is based on the waveguide invariant such that the dispersion associated with all of the normal modes is removed at the same time. After performing DDT on a signal received in the Pekeris waveguide, the waveform of resulting normal modes is very close to the source signal, each with different position and amplitude. Each normal mode can be extracted by determining its position and amplitude parameters by applying particle swarm optimization (PSO). The waveform of the extracted normal mode is simply the waveform of the source signal; the real waveform of the received normal mode can then be recovered by applying dispersion compensation to the source signal. The method presented needs only one receiver and is verified with experimental data

Lubrication and heat transfer control are two significant functions of mold fluxes. In order to coordinate the contradiction between lubrication and heat transfer, the effects of BaO and Li2O on basic characteristics of CaO-SiO2 based mold fluxes were studied by hemispherical melting temperature instrument, rotating cylinder method, X-ray diffractometer (XRD) in present study. The results show that the melting temperature and viscosity at 1300°C all represent a downward trend with BaO and Li2O enhancement at different basicity, and the break temperature decrease with BaO addition while decrease and then increase with Li2O addition, which illustrates that Li2O content should be no more than 0.8 wt% for the purpose of lubrication. Meanwhile, to ensure a sufficient thickness of the liquid slag film and avoid discontinuity of the liquid slag film, the BaO content is better to be 10 wt% with low melting temperature and viscosity. The main crystalline phase in the mold fluxes is cuspidine (3CaO·2SiO2·CaF2), and the crystallization ratio rises sharply when basicity increased to 1.65. For better deal with the contradiction of lubrication and heat transfer, the mold fluxes composition w(BaO) = 10 wt%, w(Li2O) = 0.8 wt%, R ≥1.65 is reasonable, which has a profound impact on high crystallization and lubricity mold fluxes.