In this paper a two-disc spinning disc reactor for intensified biodiesel synthesis is described and numerically simulated. The reactor consists of two flat discs, located coaxially and parallel to each other with a gap of 0.2 mm between the discs. The upper disc is located on a rotating shaft while the lower disc is stationary. The feed liquids, triglycerides (TG) and methanol are introduced coaxially along the centre line of rotating disc and stationary disc. Fluid hydrodynamics in the reactor for synthesis of biodiesel from TG and methanol in the presence of a sodium hydroxide catalyst are simulated, using convection-diffusion-reaction species transport model by the CFD software ANSYS©Fluent v. 13.0. The effect of the upper disc’s spinning speed is evaluated. The results show that the rotational speed increase causes an increase of TG conversion despite the fact that the residence time decreases. Compared to data obtained from adequate experiments, the model shows a satisfactory agreement.

A rotor-stator spinning disk reactor for intensified biodiesel synthesis is described and numerically simulated in the present research. The reactor consists of two flat disks, located coaxially and parallel to each other with a gap ranging from 0.1 mm to 0.2 mm between the disks. The upper disk is located on a rotating shaft while the lower disk is stationary. The feed liquids, triglycerides (TG) and methanol are injected into the reactor from centres of rotating disk and stationary disk, respectively. Fluid hydrodynamics in the reactor for synthesis of biodiesel from TG and methanol in the presence of a sodium hydroxide catalyst are simulated, using convection-diffusion-reaction multicomponent transport model with the CFD software ANSYS©Fluent v. 13.0. Effect of operating conditions on TG conversion is particularly investigated. Simulation results indicate that there is occurrence of back flow close to the stator at the outlet zone. Small gap size and fast rotational speed generally help to intensify mixing among reagents, and consequently enhance TG conversion. However, increasing rotational speed of spinning disk leads to more backflow, which decreases TG conversion. Large flow rate of TG at inlet is not recommended as well because of the short mean residence time of reactants inside the reactor.

A new concept of an electrostatic spray column for liquid-liquid extraction was investigated. An important problem for separation processes is the presence of azeotropic or close-boiling mixtures in their production, for example heptane with ethanol, since the separation is impossible by ordinary distillation. The use of ionic liquids (IL) as a dispersed solvent specially engineered for any specific organic mixture in terms of selectivity is a key factor to successful separation. As IL present particularly attractive combination of favorable characteristics for the separation of heptane and ethanol, in this work we use 1-butyl-3-methylimidazolium methyl sulfate [BMIM][MeSO4]. Because of high viscosity and relatively high cost of IL a new technique was introduced, consisting in the electrostatically spray generation to enhance the mass transport between the phases. In order to optimally design the geometry of the contactor a series of numerical simulation was performed. Especially multi-nozzle variants for better exploitation of contactor volume were investigated. Experiments showed excellent possibility of control of the dispersion characteristics by applied voltage and thus control of the rate of extraction. The preliminary simulations based on our mathematical model for a three nozzle variant exhibited visual agreement with the theory of electrostatics.

Liquid-liquid extraction provides an environmentally friendly process as an alternative to azeotropic distillation, pervaporation and reverse osmosis because these techniques require the use of large amounts of energy, may involve volatile organic compounds, and operation at high pressure.

Ionic liquids (ILs) continue to gain wide recognition as potential environmentally friendly solvents due to their unique properties. However due to their current high cost, their use in industry is seriously limited without an efficient methodology for recovery and recycle.

In this paper we describe an innovative methodology for a liquid-liquid extraction process based on an electrically induced emulsion of an ionic liquid as the extracting solvent dispersed in an organic mixture. This offers a most efficient exploitation of the solvent. On the other hand we present our own design of a pilot (semi-industrial) scale extractor based on this methodology and which demonstrates effective recovery of the ionic liquid. In order to achieve this goal we used a numerical modelling tool implemented using our own simulation software based on the finite element method. We also used our original previous experience with generating and investigating liquid-liquid electrosprays using phase Doppler anemometry. Finally we present recommendations for contactor geometry and for the preferred operating conditions for the extractor.

The results of activity studies of four catalysts in methanol synthesis have been presented. A standard industrial catalyst TMC-3/1 was compared with two methanol catalysts promoted by the addition of magnesium and one promoted by zirconium. The kinetic analysis of the experimental results shows that the Cu/Zn/Al/Mg/1 catalyst was the least active. Although TMC-3/1 and Cu/Zn/Al/Mg/2 catalysts were characterised by a higher activity, the most active catalyst system was Cu/Zn/Al/Zr. The activity calculated for zirconium doped catalyst under operating conditions was approximately 30% higher that of TMC-3/1catalyst. The experimental data were used to identify the rate equations of two types - one purely empirical power rate equation and the other one - the Vanden Bussche & Froment kinetic model of methanol synthesis. The Cu/ZnO/Al2O3 catalyst modified with zirconium has the highest application potential in methanol synthesis.