Search results

Filters

  • Journals
  • Date

Search results

Number of results: 6
items per page: 25 50 75
Sort by:
Download PDF Download RIS Download Bibtex

Abstract

Cast Hadfield steel is characterised by high abrasion resistance, provided, however, that it is exposed to the effect of dynamic loads.

During abrasion without loading, e.g. under the impact of loose sand jet, its wear resistance drops very drastically. To increase the abrasion

resistance of this alloy under the conditions where no pressure is acting, primary vanadium carbides are formed in the metallurgical

process, to obtain a composite structure after the melt solidification. The primary, very hard, carbides uniformly distributed in the

austenitic matrix are reported to double the wear resistance of samples subjected to the effect of a silicon carbide-water mixture.

Go to article

Authors and Affiliations

G. Tęcza
J. Głownia
Download PDF Download RIS Download Bibtex

Abstract

Cast high-manganese Hadfield steel is commonly used for machine components operating under dynamic load conditions. Their high fracture toughness and abrasive wear resistance is the result of an austenitic structure, which - while being ductile - at the same time tends to surface harden under the effect of cold work. Absence of dynamic loads (e.g. in the case of sand abrasion) causes rapid and premature wear of parts. In order to improve the abrasive wear resistance of cast high-manganese steel for operation under the conditions free from dynamic loads, primary titanium carbides are produced in this cast steel during melting process to obtain in castings, after melt solidification, the microstructure consisting of an austenitic matrix and primary carbides uniformly distributed therein. After heat treatment, the microhardness of the austenitic matrix of such cast steel is up to 580 μHV20 and the resulting carbides may reach even 4000 μHV20. The impact strength of this cast steel varies from 57 to 129 and it decreases with titanium content. Compared to common cast Hadfield steel, the abrasive wear resistance determined in Miller test is at least twice as high for the 0.4% Ti alloy and continues growing with titanium content.

Go to article

Authors and Affiliations

R. Zapała
G. Tęcza
Download PDF Download RIS Download Bibtex

Abstract

Widely used in the power and mining industry, cast Hadfield steel is resistant to wear, but only when operating under impact loads.

Components made from this alloy exposed to the effect of abrasion under load-free conditions are known to suffer rapid and premature

wear. To increase the abrasion resistance of cast high-manganese steel under the conditions where no dynamic loads are operating, primary

titanium carbides are formed in the process of cast steel melting, to obtain in the alloy after solidification and heat treatment, the

microstructure composed of very hard primary carbides uniformly distributed in the austenitic matrix of a hardness superior to the

hardness of common cast Hadfield steel. Hard titanium carbides ultimately improve the wear resistance of components operating under

shear conditions. The measured microhardness of the as-cast matrix in samples tested was observed to increase with the increasing content

of titanium and was 380 HV0.02 for the content of 0.4%, 410 HV0.02 for the content of 1.5% and 510 HV0.02 for the content of 2 and

2.5%. After solution heat treatment, the microhardness of the matrix was 460÷480 HV0.02 for melts T2, T3 and T6, and 580 HV0.02 for

melt T4, and was higher than the values obtained in common cast Hadfield steel (370 HV0.02 in as-cast state and 340÷370 HV0.02 after

solution heat treatment). The measured microhardness of alloyed cementite was 1030÷1270 HV0.02; the microhardness of carbides

reached even 2650÷4000 HV0.02.

Go to article

Authors and Affiliations

A. Garbacz-Klempka
G. Tęcza
Download PDF Download RIS Download Bibtex

Abstract

The effect of CaSiAl modification (43-49% Ca, 43-48% Si, 2% Al) on the non-metallic inclusions and mechanical properties of cast lowcarbon steel is discussed. Tests were carried out on the cast steel with 0.2% C and micro-additives of V and Nb, used mainly for heavy steel castings (e.g. slag ladles). The modifier in an amount of 1.5 and 3 kg / Mg was introduced to the liquid steel before tapping the metal into a ladle. Test ingots of Y type and a weight of 10 kg were cast and then subjected to a normalizing heat treatment. Using light microscopy and scanning electron microscopy, qualitative and quantitative evaluation of the non-metallic inclusions present in as-cast samples was carried out. Additionally, tests of mechanical strength and impact strength were performed on cast steel with and without the different content of modifier. It was found that increasing the modifier addition affected impact strength but had no significant effect on tensile strength and yield strength. The material with high impact strength had the smallest area fraction of non-metallic inclusions in the microstructure (0.20%). The introduction of modifiers changed the morphology of non-metallic inclusions from dendritic to regular and nodular shapes.

Go to article

Authors and Affiliations

B. Kalandyk
R. Zapała
S. Sobula
G. Tęcza
Download PDF Download RIS Download Bibtex

Abstract

The results of the modification of austenitic matrix in cast high-manganese steel containing 11÷19% Mn with additions of Cr, Ni and Ti

were discussed. The introduction of carbide-forming alloying elements to this cast steel leads to the formation in matrix of stable complex

carbide phases, which effectively increase the abrasive wear resistance in a mixture of SiC and water. The starting material used in tests

was a cast Hadfield steel containing 11% Mn and 1.34% C. The results presented in the article show significant improvement in abrasive

wear resistance and hardness owing to the structure modification with additions of Cr and Ti.

Go to article

Authors and Affiliations

B. Kalandyk
R. Zapała
G. Tęcza
S. Sobula

This page uses 'cookies'. Learn more