The green peach aphid, Myzus persicae (Sulzer), is a polyphagous and holocyclic aphid which significantly damages agricultural crops. In the current study, the effects of micronutrients on some secondary metabolites of bell pepper (Capsicum annum L.) leaves and their subsequent influence on the life table parameters of M. persicae were investigated under greenhouse conditions. The flavonoid content in bell pepper leaves significantly changed following micronutrient treatments in the wavelength of 270 nm while there were no significant differences in the wavelengths 300 and 330 nm. The highest anthocyanin content was recorded after Fe treatment (3.811 mg ⋅ ml–1) while the total phenolic content in the bell pepper leaves increased after Mn (541.2 mg ⋅ ml–1) treatment compared to Fe (254.5 mg ⋅ ml–1) and control (216.33 mg ⋅ ml–1), respectively. The highest values of intrinsic (r) and finite rates of population increase (λ) of M. persicae were gained with Zn (0.320 and 1.377 day–1, respectively) treatment although the highest and the lowest values of the mean generation time (T) were found with Fe and Zn (14.07 and 12.63 days, respectively) treatments, respectively. Our findings suggest that Mn, more than Zn micronutrients, decreased ecological fitness of green peach aphid and may help enhance the efficiency of pest control techniques.

Different techniques have been devised to detect herbicide resistance in weeds, and the overall aim from this study was to compare four different assay techniques for evaluating acetolactate synthase (ALS)-inhibiting herbicide resistance in sterile wild oat (Avena sterilis L.). A resistant sterile wild oat population (R) was collected from the wheat field in Kozan, Adana province, Turkey. The susceptible (S) population was collected from the border of the same field. Effects of different doses of mesosulfuron-methyl + iodosulfuron-methyl -sodium and pyroxsulam + cloquintocet-mexyl were assessed in agar based (seed and seedling) assay, Petri dish with seeds, and whole plant pot assay. In the agar based assays, the level of resistance was evaluated by measuring coleoptile and hypocotyl lengths, and survival of seedlings. Plant height and shoot dry weight were measured in the Petri dish and whole plant pot assays, respectively. Results from the dose response analyses showed that both the R and S populations were extremely sensitive to mesosulfuron-methyl + iodosulfuron in the seedling bioassay. The resistance indices (RI’s) of the R biotype treated with mesosulfuron-methyl + iodosulfuron in the agar based seed, Petri dish, and whole plant assays were 2.29, 2.63 and 4.18, respectively. The resistance indices of the R biotype treated with pyroxsulam + cloquintocet-mexyl was 3.41, 5.05 and 2.82 in the agar based seed, Petri dish, and whole plant pot assays, respectively. The agar based seed assays and Petri dish assay provided feasible, accurate, rapid, and cost effective opportunities to identify resistance in sterile wild oat.

Gene postulation is one of the fastest and most cost-effective methods for identifying seedling leaf rust resistance genes in wheat cultivars. Many researchers use this approach to identify Lr genes in wheat cultivars. The purpose of our research was to identify seedling leaf rust resistance genes in 20 wheat cultivars from different breeding centers of Russia, Ukraine and Germany. Forty-two near isogenic Thatcher lines and 10 Puccinia triticina isolates were used for gene postulation. When assessing the infection types to cultivars and lines, a scale was used, according to Oelke and Kolmer. In 20 wheat cultivars 19 Lr genes were postulated: 2c, 3, 10, 3bg, 3ka, 14a, 17, 18, 23, 25, 26, 30, 33, 40, 44, 50, B, Exch, Kanred. The most common for cultivars was the Lr10 gene. In five cultivars, showing high field resistance, most postulated seedling genes (Lr2c, Lr3, Lr10, Lr14а, Lr26, Lr33) were not effective in the adult stage. It is possible that resistance of such cultivars is associated with APR genes, the postulation of which requires an expansion in the number and spectrum of P. triticina isolate virulence. Most of the studied cultivars (60%) have recently been entered into the register (2015–2019) and in the field show a stable or moderately susceptible response to P. triticina infection, despite the fact that the Lr genes postulated in them were not effective in the adult stage. The data obtained indicated a variety of genotypes of the studied cultivars, as well as the tendency of breeders to use the effect of pyramiding ineffective genes, which can prolong the resistance of the cultivar. Annual monitoring of varieties is necessary in each region, especially when reacting with a medium susceptible type (MS), which may indicate the initial stage of resistance loss.

Heat treatment processes, due to qualitative requirements for the cast machinery components and restrictions on energy consumption resulting on the one hand from environmental concerns, and on the other hand from a requirements coming from minimization of manufacturing costs, are resulting in searching after a technologies enabling obtainment of satisfactory results, in form of improved mechanical properties mainly, while minimizing (limiting) parameters of successive operations of the heat treatment. Heat treatment of the T6 type presented in this paper consists in operations of heating of investigated alloys to suitably selected temperature (range of this temperature was evaluated on the base of the ATD method), holding at such temperature for a short time, and next rapid cooling in water (20 oC) followed by artificial ageing, could be such technology in term s of above mentioned understanding of this issue. Performed T6 heat treatment with limited parameters of solutioning operation resulted in visible increase in tensile strength Rm of AlSi7Mg, AlSi7Cu3Mg and AlSi9Cu3(Fe) alloys.

The fluidity is the term to determine the materials ability to fill the mold cavity properly. Fluidity is complex property with many variables. Up to this date, there is no methodology for defining the fluidity in a semisolid material state. Submitted paper deals with the proposal of a new method designed for aluminium alloy fluidity evaluation in semi-solid state trough the design of the layered construction die. Die will be primary used for fluidity tests of semi-solid squeeze casted aluminium alloy and to observe the pressing force flow by mentioned casting technology. The modularity consists of possibility to change each die segment. In the experiment the die design was evaluated by simulation in ProCAST 11.5 and by production of experimental castings. The die was made by laser cutting technology from construction steel S355JR. Experimental material was aluminium alloy AlSi7Mg0.3. The temperature of the semisolid state was chosen to achieve 35% of solid phase. The result of next study should be a selected parameters observation and their effect on the fluidity of aluminium alloy in semi-solid state. This will be very important step to determine the optimal conditions to achieve a castings with certain wall thickness produced by the method of semi-solid squeeze casting.

This article presents a sequential model of the heating-remelting-cooling of steel samples based on the finite element method (FEM) and the smoothed particle hydrodynamics (SPH). The numerical implementation of the developed solution was completed as part of the original DEFFEM 3D package, being developed for over ten years, and is a dedicated tool to aid physical simulations performed with modern Gleeble thermo-mechanical simulators. Using the developed DEFFEM 3D software to aid physical simulations allows the number of costly tests to be minimized, and additional process information to be obtained, e.g. achieved local cooling rates at any point in the sample tested volume, or characteristics of temperature changes. The study was complemented by examples of simulation and experimental test results, indicating that the adopted model assumptions were correct. The developed solution is the basis for the development of DEFFEM 3D software aimed at developing a comprehensive numerical model allows the simulation of deformation of steel in semi solid state.

With the aid of eutectic modification treatment, the precipitation of coarse lamellar eutectic silicon can be suspended during the solidification of aluminum-silicon alloys, thereby the formation of fine-grained, fibrous eutectic Si can be promoted by the addition of small amounts of modifying elements, such as Sr, to the liquid alloy. The effectiveness of this technique is, however, highly dependent on many technological factors, and the degree of modification can be lowered during the various stages of melt preparation due to the oxidation of the Sr-content of the melt. During our research, we investigated the effect of rotary degassing melt treatments coupled with the addition of three different fluxes on the degree of modification of an Al-Si-Mg-Cu casting alloy. It was also studied, that whether additional Sr alloying made before and during the melt treatments can compensate the Sr fading with time. The degree of eutectic modification was characterized by thermal analysis (TA) and the microscopic investigation of TA specimens. It was found, that by using one of the three fluxes, and by adding Sr master alloy rods before the melt treatments, better modification levels could be achieved. It was also found that the measurement of Sr-concentration by optical emission spectroscopy alone cannot be used for controlling the level of eutectic modification.

The paper discusses the effect of upsetting ratio on distribution of the microhardness in longitudinal sections of hydroformed axisymmetric elements made from P265TR1 steel. The experimental research of hydroforming was carried out at a special stand which included a press with tooling and a hydraulic feeding system of oil. The measurements of microhardness were taken with a MATSUZAWA MMT-X3 Vickers hardness tester at a load of 100 g. The samples used in the tests were prepared from tube segments with a thin-wall ratio of 0.045. In the experiment, steel components were formed at upsetting coefficients of 0.07 and 0.09. For an established course of pressure and upsetting force, a series of steel components with exact representation of the die-cavity was formed. The paper provides a comparison of the microhardness distributions in three zones of longitudinal sections of axisymmetric elements at different degrees of material deformation. The greatest values of microhardness occurred in the area of cap for components at an upsetting coefficient 0.09.