Disseminated intravascular coagulation (DIC) is a complex, dynamic and hemostatic disorder which develops secondarily to a disease characterized with an imbalance in the pro-coagulant and anti-coagulant components of hemostasis. The aim of the study is to evaluate hemostatic dysfunc- tion and the DIC syndrome in cattle with displaced abomasum (DA), with using the hematologic analyses and an extensive coagulation profile in the 96 hour-period including before and after surgery. The animal material of the study consisted of 12 dairy cows diagnosed with displaced abomasum (9 LDA and 3 RDA without volvulus) in the 2-4 week period after parturation and with no other post-partum disease. In dairy cows diagnosed with DA, hematological, coagulomet- ric (PT, APTT, Fibrinogen) and coagulation factor analyses [D-Dimer, TAT (thrombin-anti- thrombin complex), ATIII (antithrombin III), PAI-1 (plazminogen activator inhibitor-1] were performed in blood samples obtained before the operation as well as 30 minutes, 60 minutes and 2, 5, 10, 24, 48, 72 and 96 hours after the operation. In the DA cases, abnormalities were found in 6 of the 8 coagulation parameters. In the LDA and RDA groups, prolonged PT (sec), PT (INR) and APTT, hypofibrinogenemia, an increase in serum D-Dimer concentration at 72 and 96 hours after the operation and an increase in serum ATIII concentrations before and 30, 60 minutes and 2, 5, 72 and 96 hours after the operation was found (p<0.05). Hemostatic dysfunction and the risk of DIC developing in DA cases and continuing in the post-operative period was determined.

This paper presents the results of a composite consisting mainly of industrial waste bound by a hydraulic binder. The composite consists of unburnt coal-mining slate, shredded rubber waste (SRW), fly ash and CEM I cement. The purpose of using the above components was to protect the unburnt coal-mining slate from the negative effects of water, which causes degradation of the aggregate grain size and significantly affects the load-bearing capacity of the aggregate. This was achieved through the use of a binder consisting of shredded waste rubber, fly ash and cement, which imparts hydrophobic properties to the composite. The composite is to be used in road pavement construction and earthworks as a substitute for standard materials. This paper focuses on testing the effects of 5, 10 and 15% additions of shredded rubber waste (SRW) on the physical and mechanical parameters of the composite, mainly compressive strength, water absorption by mass, capillary rise and deformability under cyclic loading. The composite was tested under cyclic loading conditions using a measurement system based on digital image correlation (DIC), with which the deformations occurring on the surface of the test specimens were determined. The results obtained showed the influence of shredded rubber waste additives on the decrease in compression strength (after 7 and 28 days of specimen care), mass water absorption and capillary rise, as well as an increase in the deformability of the composite under destructive loading and cyclic loading.

It is highly important to determine eigenvalues before and after certain extreme events that may cause damage accumulation, such as earthquake, blasts and mining or seismic tests on research models. Unique experiment design and shake table testing was performed to investigate seismic performance of a 3D RC building model with infill walls and advanced protection with polyurethane-based joints and fiber polymer reinforced light and emergency jackets. For the purpose of wider experimental activities, three methods for determination of the dynamic characteristics were used during multiple successive shake table tests following a dynamic pushover approach, and they are presented in detail. They are: inertance function through impact hammer tests, standard Fourier transformation of measured acceleration time history and digital image correlation. The expected differences in the results are related to the type and intensity of excitation used, the involvement of materials with different mechanical and physical properties, and with the different rate and extent of damage accumulation, as well as to local or global measurements. Y et, all methods lead to reliable results when a consistent methodology is being used, that takes into account locality or globality of measurements, leaving a choice for the most suitable one, depending on the site conditions. The inertance function method presented manifested its high efficiency in analysis of dynamic properties of large-scale structures and in monitoring of their changes caused by the damage and repair process. It offers quite a wide range of useful information, does not require very expensive equipment and its transportation cost is negligible. This method seems to be a proper diagnostic tool for simple experimental modal analysis of real structures and their structural elements, where detection of changes in the structural condition and in dynamic properties is required, also as a non-destructive testing and monitoring method. Digital image correlation proved to be a promising non-contact tool, strongly supporting the conventional instrumentation of shake table testing, while the Fourier transformation was used as a benchmark method yielding the most reliable results.

The paper presents the experimental research and numerical simulations of reinforced concrete beams under torsional load. In the experimental tests Digital Image Correlation System (DIC System) Q-450 were used. DIC is a non-contact full-field image analysis method, based on grey value digital images that can determine displacements and strains of an object under load. Numerical simulations of the investigated beams were performed by using the ATENA 3D – Studio program. Creation of numerical models of reinforced concrete elements under torsion was complicated due to difficulties in modelling of real boundary conditions of these elements. The experimental research using DIC can be extremely useful in creating correct numerical models of investigated elements. High accuracy and a wide spectrum of results obtained from experimental tests allow for the modification of the boundary conditions assumed in the numerical model, so that these conditions correspond to the real fixing of the element during the tests.

Construction is one of the industrial sectors responsible for the use of large quantities of natural raw materials. This fact makes it necessary to look for new technologies of producing construction materials based as much as possible on waste materials. Such a solution could have positive effects on the environment and reduce construction costs. This paper presents the results of a study on the deformability of a mix made from anthropogenic waste combined with a hydraulic binder. The presented mixes consist of unburnt coal mining slates (mine waste), shredded rubber waste, silica fly ash and CEM I 42.5 R cement. Samples with two different contents of shredded rubber waste 0% and 10% were made from the mixtures and subjected to destructive compressive strength testing. The strength testwas combined with sample deformation measurement performed with the Aramis 3D Video Correlation System. The results presented show the effect of the shredded rubber waste content on the deformability of the sample.