Strained layer InGaAs/GaAs SCH SQW (Separate Confinement Heterostructure Single Quantum Well) lasers were
grown by Molecular Beam Epitaxy (MBE). Highly reliable CW (continuous wave) 980-nm, broad contact, pump lasers were
fabricated in stripe geometry using Schottky isolation and ridge waveguide construction. Threshold current densities of the
order of Jth ≈ 280 A/cm2 (for the resonator length L = 700 um) and differential efficiency η= 0.40 W/A (41%) from one
mirror were obtained. The record wall-plug efficiency for AR/HR coated devices was equal to 54%. Theoretical estimations
of above parameters, obtained by numerical modelling of devices were Jth ≈ 210 A/cm and η = 0.47 W/A from one mirror,
respectively. Degradation studies revealed that uncoated and AR/HR coated devices did not show any appreciable degradation
after 1500 hrs of CW operation at 35oC heat sink temperature at the constant optical power (50 mW) conditions.
In this contribution an optical method of controlling the state of soft biological tissues in real time, exposed to laser radiation is discussed. The method is based on the assumption that the change dynamics of the amplitude of the scattered diagnostic radiation (λ = 635 nm) is compatible with the change dynamics of the tissue inner structure exposed to the Nd:YAG laser radiation (λ = 1064 nm). In this method the measurement of the tissue temperature is omitted. Exemplary results of the laboratory research on this method and an interpretation of the results are presented.
A mode-locked Tm3+-doped fibre laser and amplifier operating at a central wavelength of 1994.3 nm is demonstrated. A thulium oscillator is passively mode-locked by a semiconductor saturable absorber mirror to generate an average power of 17 mW at a fundamental repetition rate of 81 MHz in a short linear cavity. This 2-µm laser train is amplified to an average power to 20.26 W by two double-clad thulium-doped allfibre amplifiers. The pulse energy, duration and peak power is 250 nJ, 23 ps and 9.57 kW, respectively. This represents one of the highest values of average power at ∼ 2-µm-wavelength for picosecond thulium-doped fibre lasers and amplifiers. The performance of the laser system is described in details.
In this paper the overview of the recent study on the rare-earth activated waveguides performed in the Optoelectronic Department of IMiO is presented. We reported on the development of rare earth-doped fluorozirconate (ZBLAN) glass fibers that allow a construction of a new family of visible and ultraviolet fiber lasers pumped by upconversion. Especially the performance of holmium devices is presented. The properties of laser planar waveguides obtained by the LPE process and the growth conditions of rare earths doped YAG layers are presented. In this paper we present also the theoretical study of the nonlinear operation of planar waveguide laser, as an example the microdisk Nd:YAG structure is discussed. We derived an approximate formula which relates the small signal gain in the Nd:YAG active medium and the laser characteristics, obtained for whispering-gallery modes and radial modes, to the output power and real parameters of the laser structure
1) Background: the modeling, characterization, transformation and propagation of high-power CW laser beams in optical (including fiberoptic) trains and in the atmosphere have become hot topics in laser science and engineering in the past few years. Single-mode output is mandatory for high-power CW laser applications in the military field. Moreover, an unstationary, dynamic operation regime is typical. Recognized devices and procedures for laser-beam diagnostics could not be directly applied because of dynamic behavior and untypical non-Gaussian profiles. 2) Methods: the Wigner transform approach was proposed to characterize dynamically variable high-power CW laser beams with significant deterministic aberrations. Wavefront-sensing measurements by means of the Shack-Hartmann method and decomposition into an orthogonal Zernike basis were applied. 3) Results: deterministic aberration as a result of unstationary thermal-optic effects depending on the averaged power of the laser output was found. Beam quality determined via the Wigner approach was changed in the same way as the measurements of the beam diameter in the far field. 4) Conclusions: such an aberration component seems to be the main factor causing degradation in beam quality and in brightness of high-power CW laser beams.
The paper describes the research on soft X-ray lasers with an active medium created using a gas puff target irradiated
with high-intensity laser pulses. The gas puff target in a form of an elongated gas sheet is produced by pulsed injection of
gas through a slit nozzle using a high-pressure electromagnetic valve. The method of generation of soft X-ray lasers using a
laser-irradiated gas puff target has been developed at the Institute of Optoelectronics. The collaborative experiments were
performed at various laser laboratories using high-intensity laser systems to irradiate the gas puff target and pump the X-ray
laser active medium. Results of these experiments are presented and discussed. Works aimed at increasing the efficiency of
X-ray lasers using a longitudinally irradiated gas puff target are also reviewed.
This paper presents the results of a numerical analysis of nitride-based edge-emitting lasers with an InGaN/GaN active region designed for continuous wave room temperature emission of green and blue light. The main goal was to investigate whether the indium thin oxide (ITO) layer can serve as an effective optical confinement improving operation of these devices. Simulations were performed with the aid of a self-consistent thermal-electrical-optical model. Results obtained for green- and blue-emitting lasers were compared. The ITO layer in the p-type cladding was found to effectively help confine the laser mode in the active regions of the devices and to decrease the threshold current density.
Self-swept erbium fiber laser emitting around 1.56 μm is reported in detail. Both sweep directions were registered: pointing toward longer and shorter wavelengths, redshift and blueshift sweeping, respectively. We describe method of determining the direction of the wavelength drift using the monochromator based optical spectrum analyzer. Possible root for this sweeping regime, i.e., the gain modulation along active fiber, is discussed with the help of a simple model calculating the overall cavity gain that can predict the direction of the laser wavelength sweeping.
An efficient operation of a Ho:YLF laser pumped by a Tm-doped fibre laser is reported. The research in a continuous-wave (CW) operation was done for two crystals of the same 0.5 at.%Ho dopant concentration and with different lengths (3×3×30 mm3 and 3×3×50 mm3). For an output coupling transmission of 20% and a crystal length of 50 mm, the maximum CWoutput power of 38.9 W for 81.4 W of incident pump power, corresponding to the slope efficiency of 52.3% and optical-to-optical conversion efficiency of 47.8% (determined with respect to the incident pump power) was achieved. The highest opti- cal-to-optical conversion efficiency of 70.2% with respect to the absorbed pump power was obtained. The influence of a heat-sink cooling water temperature on theCWlaser performance was studied. For a Q-switched operation the pulse repe- tition frequency (PRF) was changed from 2 to 10 kHz. The maximum average output power of 34.1 W at the PRF of 10 kHz was obtained for a 50 mm holmium crystal length. For 2 kHz PRF and 71.9 W of incident pump power, pulse energies of 13.7 mJ with a 21 ns FWHM pulse width corresponding to 652 kW peak power were recorded.
In this paper, the two-temperature thermoelasticity model is proposed to a specific problem of a thermoelastic semi-infinite solid. The bounding plane surface of the semi-infinite solid is considered to be under a non-Gaussian laser pulse. Generalized thermoelasticity analysis with dual-phase-lags is taken into account to solve the present problem. Laplace transform and its inversion techniques are applied and an analytical solution as well as its numerical outputs of the field variables are obtained. The coupled theory and other generalized theory with one relaxation time may be derived as special cases. Comparison examples have been made to show the effect of dual-phase-lags, temperature discrepancy, laser-pulse and laser intensity parameters on all felids. An additional comparison is also made with the theory of thermoelasticity at a single temperature.
Widely-tunable, fully-monolithic, mid-infrared (mid-IR) deference frequency generation source (DFG) is presented. By using a custom designed fiber-pigtailed periodically poled lithium niobate (PPLN) crystal module the idler beam was generated with an efficiency of 21%/W, yielding 2.6 mW of optical output power. The proposed all-fiber configuration radically simplified the optical frequency conversion setup, making it robust and easily configurable. The usefulness of the constructed source was verified by performing simultaneous wavelength modulation spectroscopy (WMS) laser trace gas detection of methane, near 2999 cm−1, and ethane, near 2997 cm−1, via two independently generated, tunable idler beams.
We demonstrate MW-level, single resonance optical parametric oscillator, based on KTP Type-II crystal with noncritical phase-matching. The OPO is pumped by electro-optically Q-switched Nd:YAG slab laser providing 55 mJ of pulse energy. At the output, we achieved 28 mJ of signal pulse energy at 1.57 μm with 51% conversion efficiency, corresponding to 1.4 MW of peak power.
A new approach to passive electromagnetic modelling of coupled–cavity quantum cascade lasers is presented in this paper. One of challenges in the rigorous analysis of such eigenvalue problem is its large size as compared to wavelength and a high quality factor, which prompts for substantial computational efforts. For those reasons, it is proposed in this paper to consider such a coupled-cavity Fabry-Perot resonant structure with partially transparent mirrors as a two-port network, which can be considered as a deterministic problem. Thanks to such a novel approach, passive analysis of an electrically long laser can be split into a cascade of relatively short sections having low quality factor, thus, substantially speeding up rigorous electromagnetic analysis of the whole quantum cascade laser. The proposed method allows to determine unequivocally resonant frequencies of the structure and the corresponding spectrum of a threshold gain. Eventually, the proposed method is used to elaborate basic synthesis rules of coupled–cavity quantum cascade lasers.
The paper concerns the accuracy of determining particle size distributions of the fine-grained materials by means of laser diffraction method. Selection of measuring method for determination of materials granulation depends on various properties of the sample, but mainly on the range of particle size in the sample. It must be taken into consideration that each of the measurement methods inherently generate different information about particle size distribution. The applied measurement method generates the main impact on the results of research because it uses various material properties, like: geometric properties, density or type of the surface (porosity).
Influence of density and particle shape on the results of measurements by laser diffraction was studied in the paper. This method becomes a standard for measuring particle size of mineral powders. Analysis of raw materials particle size distribution was performed using a laser particle-meter Analysette 22. Investigations included measurements of particle size of raw materials characterized by various densities (coal, porphyry, barite) and the shape of the particles (copper shale ore, fly ash from coal combustion). The density of raw materials was determined by helium pycnometer, while the particle shape was expressed by coefficient which was calculated on the basis of particles geometric parameters. Geometry of the grains was measured using an optical microscope with a digital record of images by means of image analysis method. The accuracy of laser granulometric analyzes was expressed by variation coefficient of narrow particle fractions contents. Results of analyzes confirmed that the laser granulometric analysis provides accurate information about the finestparticle size distribution. No significant effect of the material density on the accuracy of granulometric analysis was observed. Effect of particle shape of the tested materials caused more stable values of the variation coefficient for particles of more spherical shape what is related to the applied method of laser measurement. The accuracy of laser granulometric analyzes varies dependably on the measured particle size range of particles. The most accurate analyzed materials are these ones being the part of narrow particle fractions.
This paper presents a new stand for studying the linear shrinkage kinetics of foundry alloys. The stand is equipped with a laser displacement sensor. Thanks to this arrangement, the measurement is of a contactless nature. This solution allows for the elimination of errors which occur in measurements made using intermediary elements (steel rods). The supposition of the expansion (shrinkage) of the sample and the expansion of the heated rod lead to the distortion of the image of the actual dimensional changes of the studied sample. A series of studies of foundry alloys conducted using the new stand allowed a new image of shrinkage kinetics to be obtained, in particular regarding cast iron. The authors introduce in the study methodology a real-time measurement of two linked quantities; shrinkage (the displacement of the free end of the sample) and temperature in the surface layer of the sample casting. This generates not only a classic image of shrinkage (S) understood as S = f (t), but also the view S = f (T). The latter correlation, developed based on results obtained using the contactless method, provide a new, so far poorly known image of the course of shrinkage in foundry alloys, especially cast iron with graphite in the structure. The study made use of hypo- and hypereutectic cast iron in order to generate an image of the differences which occur in the kinetics of shrinkage (as well as in pre-shrinkage expansion - expansion occurs during solidification).
The article presents research on solid particle erosive wear resistance of ductile cast iron after laser surface melting. This surface treatment technology enables improvement of wear resistance of ductile cast iron surface. For the test ductile cast iron EN GJS-350-22 surface was processed by high power diode laser HPDL Rofin Sinar DL020. For the research single pass and multi pass laser melted surface layers were made. The macrostructure and microstructure of multi pass surface layers were analysed. The Vickers microhardness tests were proceeded for single pass and multi pass surface layers. The solid particle erosive test according to standard ASTM G76 – 04 with 30°, 60° and 90° impact angle was made for each multi pass surface layer. As a reference material in erosive test, base material EN GJS-350-22 was used. After the erosive test, worn surfaces observations were carried out on the Scanning Electron Microscope. Laser surface melting process of tested ductile cast iron resulted in maximum 3.7 times hardness increase caused by microstructure change. This caused the increase of erosive resistance in comparison to the base material.