Metallographic investigations and a computer simulation of stresses in a gravity die-casting bushing were performed. Simulation of the casting process, solidification of the thick-walled bushing and calculations of the stress was performed using MAGMA5.3 software. The size variability of phases κIIaffecting the formation of phase stresses σf, depending on the location of the metallographic test area, was identified. The distribution of thermal σtand shrinkage stresses σs, depending on the location of the control point SC in the bushing's volume, was estimated. Probably the nature of these stresses will change slightly even after machining. This can cause variations in operating characteristics (friction coefficient, wear). Due to the strong inhomogeneity of the stress distribution in the bushing's casting, it is necessary to perform further tests of the possibility to conduct thermal treatment guaranteeing homogenization of the internal stresses in the casting, as well as to introduce changes in the bushing's construction and the casting technology. The paper presents the continuation of the results of research aimed at identifying the causes of defects in the thick-walled bushing, die-casting made of CuAl10Fe5Ni5Cr aluminium bronze.

With the increase in wall thickness of the casting of iron-nickel-aluminium-bronze, by the reduction of the cooling rate the size of κII phase

precipitates increases. This process, in the case of complex aluminium bronzes with additions of Cr, Mo and W is increased. Crystallization

of big κII phase, during slow cooling of the casting, reduces the concentration of additives introduced to the bronze matrix and hardness.

Undertaken research to develop technology of thick-walled products (g> 6 mm) of complex aluminium bronzes. Particular attention

was paid to the metallurgy of granules. As a result, a large cooling speed of the alloy, and also high-speed solidification casting a light

weight of the granules allows: to avoid micro-and macrosegregation, decreasing the particle size, increase the dispersion of phases in

multiphase alloys. Depending on the size granules as possible is to provide finished products with a wall thickness greater than 6 mm by

infiltration of liquid alloy of granules (composites). Preliminary studies was conducted using drip method granulate of CuAl10Fe5Ni5

bronze melted in a INDUTHERM-VC 500 D Vacuum Pressure Casting Machine. This bronze is a starting alloy for the preparation of the

complex aluminium bronzes with additions of Cr, Mo, W and C or Si. Optimizations of granulation process was carried out. As the process

control parameters taken a casting temperature t (°C) and the path h (mm) of free-fall of the metal droplets in the surrounding atmosphere

before it is intensively cooled in a container of water. The granulate was subjected to a sieve analysis. For the objective function was

assume maximize of the product of Um*n, the percentage weight "Um" and the quantity of granules 'n' in the mesh fraction. The maximum

value of the ratio obtained for mesh fraction a sieve with a mesh aperture of 6.3 mm. In the intensively cooled granule of bronze was

identified microstructure composed of phases: β and fine bainite (α+β'+β'1) and a small quantity of small precipitates κII phase. Get high

microhardness bronze at the level of 323±27,9 HV0,1.

For the die casting conditions of aluminium bronzes assumed based on the literature data, a thick-walled bush was cast, made of complex

aluminium bronze (Cu-Al-Fe-Ni-Cr). After the cast was removed from the mould, cracks were observed inside it. In order to identify the

stage in the technological production process at which, potentially, the formation of stresses damaging the continuity of the microstructure

created in the cast was possible (hot cracking and/or cold cracking), a computer simulation was performed. The article presents the results

of the computer simulation of the process of casting the material into the gravity die as well as solidifying and cooling of the cast in the

shape of a thick-walled bush. The simulation was performed with the use of the MAGMA5 program and by application of the

CuAl10Ni5,5Fe4,5 alloy from the MAGMA5 program database. The results were compared with the location of the defects identified in

the actual cast. As a result of the simulation of the die-casting process of this bush, potential regions were identified where significant

principal stresses accumulate, which can cause local hot and cold cracking. Until now, no research has been made of die-cast aluminium

bronzes with a Cr addition. Correlating the results of the computer simulation validated by the analysis of the actual cast made it possible

to clearly determine the critical regions in the cast exposed to cracking and point to the causes of its occurrence. Proposals of changes in

the bush die casting process were elaborated, in order to avoid hot tearing and cold cracking. The article discusses the results of

preliminary tests being a prologue to the optimization of the die-casting process parameters of complex aluminium bronze thick-walled

bushs.