This research proposes a method to enhance the payload message by embedding messages on the dilated edge areas by the Least Significant Bit (LSB) method. To add security aspects to messages, messages are not embedded directly on the LSB but encrypted with XOR operations with Most Significant Bit (MSB). The experimental results of the test in this study showed that the dilation process to some extent can increase the payload of 18.65% and the average bpp is 1.42 while maintaining the imperceptibilty quality of stego image with an average PSNR value of about 47 dB, SSIM is 0.9977 and MSE is 1.13.
In the region between King George Island and the South Orkney Islands 7 fish species from 6 families were found. The concentration of larvae at the edge of drifting ice was higher (2.55 ind. x 1000 m-3) than in the stations situated at a distance from the ice edge (0.93 ind. x 1000 m-3).
In a rectilinear route, a moving sink is restricted to travel either horizontally or vertically along the connecting edges. We present a new algorithm that finds the shortest round trip rectilinear route covering the specified nodes in a grid based Wireless Sensor Network. The proposed algorithm determines the shortest round trip travelling salesman path in a two-dimensional grid graph. A special additional feature of the new path discovery technique is that it selects that path which has the least number of corners (bends) when more than one equal length shortest round trip paths are available. This feature makes the path more suitable for moving objects like Robots, drones and other types of vehicles which carry the moving sink. In the prosed scheme, the grid points are the vertices of the graph and the lines joining the grid points are the edges of the graph. The optimal edge set that forms the target path is determined using the binary integer programming.
Buckling of the stiffened flange of a thin-walled member is reduced to the buckling analysis of the cantilever plate, elastically restrained against rotation, with the free edge stiffener, which is susceptible to deflection.Longitudinal stress variation is taken into account using a linear function and a 2nd degree parabola. Deflection functions for the plate and the stiffener, adopted in the study, made it possible to model boundary conditions and different buckling modes at the occurrence of longitudinal stress variation. Graphs of buckling coefficients are determined for different load distributions as a function of the elastic restraint coefficient and geometric details of the stiffener. Exemplary buckling modes are presented.
This paper presents the results of a numerical analysis of nitride-based edge-emitting lasers with an InGaN/GaN active region designed for continuous wave room temperature emission of green and blue light. The main goal was to investigate whether the indium thin oxide (ITO) layer can serve as an effective optical confinement improving operation of these devices. Simulations were performed with the aid of a self-consistent thermal-electrical-optical model. Results obtained for green- and blue-emitting lasers were compared. The ITO layer in the p-type cladding was found to effectively help confine the laser mode in the active regions of the devices and to decrease the threshold current density.
The aim of the study was to examine the relationship between tinnitus pitch and maximum hearing loss, frequency range of hearing loss, and the edge frequency of the audiogram, as well as, to analyze tinnitus loudness at tinnitus frequency and normal hearing frequency.
The study included 212 patients, aged between 21 to 75 years (mean age of 54.4 ± 13.5 years) with chronic subjective tinnitus and sensorineural hearing loss. For the statistical data analysis we used Chisquare test and Fisher’s exact test with level of significance p < 0:05.
Tinnitus pitch corresponding to the frequency range of hearing loss, maximum hearing loss and the edge frequency was found in 70.8%, 37.3%, and 16.5% of the patients, respectively. The majority of patients had tinnitus pitch from 3000 to 8000 Hz corresponding to the range of hearing loss (p < 0:001). The mean tinnitus pitch was 3545 Hz ± 2482. The majority (66%) of patients had tinnitus loudness 4–7 dB SL. The mean sensation level at tinnitus frequency was 4.9 dB SL ± 1.9, and 13 dB SL ± 2.9 at normal hearing frequency.
Tinnitus pitch corresponded to the frequency range of hearing loss in majority of patients. There was no relationship between tinnitus pitch and the edge frequency of the audiogram. Loudness matching outside the tinnitus frequency showed higher sensation level than loudness matching at tinnitus frequency.
The airflow in the mouth of an open and closed flue organ pipe of corresponding geometrical proportions is studied. The phase locked particle image velocimetry with subsequent analysis by the biorthogonal decomposition is employed in order to compare the flow mechanisms and related features. The most significant differences lie in the mean velocity distribution and rapidity of the jet lateral motion. Remarks on the pressure estimation from PIV data and its importance for the aeroacoustic source terms are made and a specific example is discussed.
The effectiveness of half flat tip serrations on reducing fan blade trailing edge noise was investigated using experimental methods. The experiments were conducted at an anechoic chamber under different rotating fan speeds. Numerical simulations were performed to investigate the mass flow rate generated by the serrated fan and compared with that by the baseline fan. The experimental results showed that the overall amount of noise reduction decreased with the increasing of the distance away from the fan. It was found that the effectiveness of the serrations was not proportional with the rotating speed of the fan where it was most effective at 263 rpm and 2041 rpm with noise reductions about 3.1 dBA and 3.5 dBA, respectively. This phenomenon might be depended on how trailing edge vortex would interact with the serrations at different speeds of the fan. The reduction of mass flow rate reduced with the increasing of the rotating speed and the highest reduction was found at 263 rpm which was about 18% and this reduction was accompanied by overall noise reduction of 3.1 dBA.
The purpose of this paper is to focus on the loss separation of non-grain-oriented electrical steels used for speed-variable rotating electrical machines. The impact of laser-cutting, used in prototype manufacturing and of flux density harmonics, occurring locally in the lamination, on the loss distribution is studied in detail. Iron losses occurring under operation can physically be separated in different loss components. In this paper, a frequency-based loss model with parameters identified for single-sheet tester specimens, cut in strips of different widths, is therefore used. Moreover, a time-domain approach considers loss distributions occurring from higher harmonics. Hysteresis losses having high sensitivity to cut edge effects are calculated by the well-known Jiles-Atherton model adapting the frequency-based loss parameters. The model is validated by free-curve measurements at a single-sheet tester. It has been shown that the studied elliptical hysteresis model becomes inaccurate particularly for specimens with small strip widths with similar dimensions as teeth of electrical machine laminations. The incorrect mapping of losses occurring from minor hysteresis loops due to higher harmonics is concluded. The results showconsequently that both, the impact of a cut edge effect and local distributions of flux density harmonics need to be considered in terms of accurate iron loss prediction of electrical machine design.
Altogether 105 algal taxa were identified including 101 diatom species. Chaetoceros criophilus was dominant in the western part of the study area influenced by waters from the Bellingshausen Sea. Corethron criophilum was abundant in the Weddcll Sea water mass found to the east of 53.5°W meridian. Nitzschia cylindrus common in the ice-melt samples was dominant in only two net phytoplankton collections obtained at the ice-edge zone. Additional samples from Admiralty Bay, at King George Island revealed the dominance of Chaetoceros socialis and the presence of many tychoplankton species. Very few diatom cells were found in the open waters of the Bransfield Strait which combined with the presence of krill, suggested intensive grazing by herbivores. The unstable waters of the Weddell-Scotia Confluence area contained little phytoplankton except for a station dominated by Phaeocystis pouchetii. Greater cell densities were related to warm, lower salinity Weddell Sea water of summer modification found in the surface layer east from 49°W.
This article presents a method for detecting linear objects with a defined direction based on image and lidar data. It was decided to use Gabor waves for this purpose. The Gabor wavelet is a sinusoid modulated by the Gauss function. The orientation angle of the sinusoid means that the waveform can only operate in strictly defined directions. It should, therefore, provide an appropriate solution to the problem posed by the publication. The research problem focused in the first stage on determining the approximate location of only the analysed objects, and in the next step on correct and accurate detection. The first stage was carried out using Gabor filters, the second - using the Hough transform. The tests were performed for both laser data and image data. In both cases, good results were obtained for both stages: approximate location and precise detection.
Thin-walled bars currently applied in metal construction engineering belong to a group of members, the cross-section resistance of which is affected by the phenomena of local or distortional stability loss. This results from the fact that the cross-section of such a bar consists of slender-plate elements. The study presents the method of calculating the resistance of the cross-section susceptible to local buckling which is based on the loss of stability of the weakest plate (wall). The "Critical Plate" (CP) was identified by comparing critical stress in cross-section component plates under a given stress condition. Then, the CP showing the lowest critical stress was modelled, depending on boundary conditions, as an internal or cantilever element elastically restrained in the restraining plate (RP). Longitudinal stress distribution was accounted for by means of a constant, linear or non-linear (acc. the second degree parabola) function. For the critical buckling stress, as calculated above, the local critical resistance of the cross-section was determined, which sets a limit on the validity of the Vlasov theory. In order to determine the design ultimate resistance of the cross-section, the effective width theory was applied, while taking into consideration the assumptions specified in the study. The application of the Critical Plate Method (CPM) was presented in the examples. Analytical calculation results were compared with selected experimental findings. lt was demonstrated that taking into consideration the CP elastic restraint and longitudinal stress variation results in a more accurate representation of thin-walled element behaviour in the engineering computational model