In this work microbiological air pollution at several commune sewage treatment plants (capacity up to 15,000 PE) was investigated. The bioreactors in all plants had a covered construction. The air samples were taken indoors as well as outdoors (both on the windward and leeward side) during different seasons. The samples were collected using the collision method. The presence of indicator organisms in the samples was determined according to the Polish Standards. Identification of individual indicators was performed on solid selective-differentiating substrates. To verify the presence of bacteria from Salmonella, Shigella, coliforms and enterococci species, the colonies observed on the MacConkey substrate were then sifted onto SS and Endo substrates. At all facilities (with one exception) the average CFU for the total number of bacteria and fungi did not exceed 1000/m³, which is the limit set by the Polish Standards for a pollution-free atmospheric air. Bacteria and fungi concentrations, observed at windward and leeward sides of all plants, were relatively low (<100 CFU/m³ and <1000 CFU/m³, respectively) and comparable. A sewage collection point had only a slight impact on the bioaerosol emission. The concentration of microorganisms in the immediate vicinity of covered reactors (aeration chambers) was rather low and remained below the limits sets by the Polish Standards at three facilities. The CFU of individual indicators, measured in rooms accessible for the personnel, was comparable to the CFU in technological rooms. However some indicators, e.g. a number of Actinomycetes, were significantly higher and reached >100 CFU/m³, which means significant air pollution. Similarly, the CFU of hemolytic bacteria had nonzero values. The only place where higher concentrations of bioaerosol were found was the centrifuge room, where digested sludge was dewatered. The number of fungi stayed below the limits there, but the amount of heterotrophic and hemolytic bacteria exceeded the limits and reached the values of ~10000 CFU/m³ and 800 CFU/m³, respectively; it means that the personnel working in this area is exposed to microbiological agents.

This article shows incidents associated with the use of gas as an energy carrier. It presents selected incidents which have occurred in Poland and around the world in recent decades. Based on this, consequences of gas and air mixture explosions were analysed as well. The article presents the main causes of gas incidents which have taken place, as per instances which are similar worldwide. Incidents associated with the use of gas are not frequent, but at the same time very tragic as they often lead to illness or even death. In Poland, in the last twenty years, construction area disasters caused by gas explosions account for only 5% of all which have occurred, but the number of fatalities resulting from these cases is approximately 14%. The number of individuals injured reached 39% of all construction disaster victims. Considering all these facts, it is necessary to undertake wide preventive measures in order to increase safety in the use of gaseous fuels.

Methane is accompanied by most of the coal deposits. The methane hazard is excessive content of this gas in the mining excavations. This is a source of high risk security and continuity of the mine. The Piast–Ziemowit is the only non-methane mine in the Polish Mining Group. In 2015, 66,4% of the coal mined in Kompania Węglowa S.A. mines comes from methane coal seams. Methane drainage is the most effective but very costly method of combating methane hazard.The costs of prevention and eradication of methane hazard is charged to the costs of coal mining. Therefore, performance of methane drainage in the mines of the Polish Mining Group is adapted to the scale of the methane hazard. The article presents an analysis of the costs of prevention of methane hazard for mines with different absolute methane and its impact on the level of these costs.

A proper description of ground motions generated by seismic and paraseismic events requires gathering data of six components of seismic waves. T hree of them, the so called translational waves, are well researched and identified. Unfortunately, until recently, the remaining three components named as rotational waves were generally estimated with the use of indirect methods based on theoretical calculations. T his was related mostly with the lack of proper instruments for the recording of rotational seismic waves. T hus, rotational waves were not fully recognized thus far. Recently, several types of advanced instruments for direct measurements of rotation were invented. Based on the measurements of strong ground motions it was indicated that the amplitude of the rotational components in close distances from the seismic source can be significantly larger than expected. Apart from this, there is still a lack of analyses considering the characteristic of rotational seismic waves generated by induced seismic events. In this paper, the results of preliminary measurements of rotational motions generated by induced seismic waves were presented. Ground movements related with mining tremors were analyzed in terms of amplitude, frequency and duration.

The underground mining of coal deposits in the Upper Silesian Coal Basin (GZW) re-sults in an imbalance in the distribution of the stress in the rock mass, both in the immediate and distant surroundings of mining excavations. The occurrence of seismic tremors, among others, is the consequence of this process,. The intensities of seismic phenomena, which occur in several regions of the GZW (Bytomian Basin, Main Saddle, Main Basin, Kazimierzowska Basin, and the Jejkowice Basin) are very diverse, ranging from tremors unrecognizable by humans to strong tremors of the nature of weak earthquakes (Patyńska and Stec 2017). During the period of 15 years, i.e. from 2001 to 2015, the level of seismic activity changed and de-pended on both the intensity of the excavation work and the variability of the lithological and tectonic structures. On the other hand, the seismic activity analysis has shown that in recent years, despite a decrease in total output, seismic activity and rockburst hazard have increased. One of the rea-sons was the increase in mining output. Almost half of the output came from coal seams under the rockburst hazard. This resulted in an increase in the number of great energy tremors with the energy of 107, 108 and 109 J. It has been shown that the amount of energy tremors has a high impact on the level of the rockburst hazard. Between 2001 and 2015, as many as 20 rockburst were caused by seismic tremors above 107 J with 42 total phenomena (Patyńska 2002–2016). The purpose of characterizing the causes of this phenomenon was determined by the parameters characterizing the structure of the rock mass in places where the rockburst was recorded.

The current rockburst hazard conditions in the copper mines are the consequence of mining-induced seismicity of the rock strata whilst the majority of registered rockbursts have been caused by high-energy seismic events. T he analysis of seismic activity in recent years indicates that the region of the Rudna mine is the region of the highest seismic activity. This paper is an attempt at evaluating the seismicity levels in the Rudna mine in the period from 2006-2015, within the entire mine and in its particular sections. Key parameters of seismic activity include the number of registered seismic events, total energy emission levels, and a unit energy factor. The variability of Gutenberg -Richter (GR) parameters are analyzed and the epicenters’ locations are investigated with respect to the stope position. T he distinction is made between low-energy (103 ≤ As < 105 J) and high-energy (As ≥ 105J) seismic events ahead of the stope, in the opening-up cross-throughs and in the gob areas. It appears that the risk level of a high-energy event occurrence in the R udna mine has not changed in recent years and has remained on a high level whilst the differences in seismic activity, in particular mine sections, are attributed to the varied extraction height and varied thickness of rockburst-prone carbonate layers in the roof of the copper ore deposit. The analysis of the epicenters’ locations with respect to the stope reveals that no matter what the seismic energy levels, the largest number of rockbursts are registered in the opening-up cross-through zone. Low-energy tremors are mostly located in the gob areas, high-energy events occur mostly ahead of the stope. T hus, the evaluation of the seismicity conditions in the Rudna mine seems to positively verify the relationship between the number of registered events and the levels of generated seismic energy, taking the local geological and mining conditions and the specificity of the room and pillar mining method into account.

Mining-induced seismicity, particularly high-energy seismic events, is a major factor giving rise to dynamic phenomena within the rock strata. Rockbursts and stress relief events produce the most serious consequences in underground mines, are most difficult to predict and tend to interact with other mining hazards, thus making control measures difficult to implement. In the context of steadily increasing mining depth within copper mines in the Legnica-Głogów Copper Belt Area (Poland) alongside the gradually decreasing effective mining thickness, a study of the causes and specificity of mining-induced seismicity in specific geological and mining settings may improve the effectiveness of the prevention and control measures taken to limit the negative impacts of rockbursts in underground mine workings, thus ensuring safe working conditions for miners. This study investigates the presumed relationship between the mined ore deposit thickness and fundamental parameters of mining-induced seismicity, with the main focus on the actual locations of their epicenters with respect to the working face in commonly used room-and-pillar systems. Data recalled in this study was supplied by the O/ZG Rudna geophysics station. Based on information about the actual ore deposit thickness in particular sections of the mines (Rudna Główna, Rudna Północna, Rudna Zachodnia) and recent reports on seismic activity in this area, three panels were selected for further studies (each in different mine region), where the ore deposit thickness was varied (panel G-7/5 – Rudna Główna, panel XX/1 – Rudna Północna, panel XIX/1 – Rudna Zachodnia). Data from seismic activity reports in those regions was used for energetic and quantitative analysis of seismic events in the context of the epicenter location with respect to the selected mining system components: undisturbed strata, working face and abandoned excavations. In consideration of the available rockburst control methods and preventive measures, all events (above 1 × 103 J) registered in the database were analysed to infer about the global rockburst hazard level in the panel and phenomena induced (provoked) by blasting were considered in order to evaluate the effectiveness of the implemented control measures.

The introduction of the article presents the problem of interpreting the level of fire hazard basing on Graham’s ratio, which, in certain ranges of the value of its denominator, may be wrong. The range of credibility for the index is also discussed. The issue of nitrogen inertisation and its influence on the value of the discussed index is also addressed. To determine the influence, two statistical samples were set. They consisted of the results of precise chromatographic analyses of the air samples collected in the longwall areas which were not subjected to inertisation and in the areas where nitrogen was applied as the inert gas. Then, with Student’s t-test, there was conducted a comparative analysis of both groups with regard to the equality of the average concentrations of gases emitted in the coal self-heating process. At the end, there were developed criteria for the application of Graham’s ratio for the air samples of the increased content of nitrogen, which, according to the discussed index, did not indicate the occurrence of an endogenous fire hazard.

There are about 8.5 million workers employed in the construction sector in India. Construction workers constitute a major portion of the unorganized labour and are characterized by their casual nature of employment, temporary relationship with the employer, prolonged and uncertain working hours, lack of safety and health measures, and inadequacy of basic amenities and welfare facilities. There are many legislation clauses providing safeguards for contract workers in India. Construction safety has been made legally enforceable after the enactment of The Building and Other Construction Workers (Regulation of Employment and Conditions of Service) Act in 1996 and the Central Rules in 1998. This paper details various statutory provisions for construction safety in India with specific reference to the BOCW Act, Central Rules, and State Rules.

The construction industry in India is the country’s second largest industrial sector, after agriculture. The construction industry makes a remarkable contribution to the Indian economy and provides employment to a large number of people of Idia. Fire is a chemical reaction of a combustible substance with oxygen, involving heat and is usually accompanied by a visual flame or incandescence. Ensuring fire safety has always been a challenge to the stakeholders, i.e. building owners, construction companies, contractors and sub-contractors, and government employees due to the multiplicity of the factors involved and their complexity. There are various legal standards and requirements for ensuring fire safety on construction sites. The buildings are normally provided with firewalls during construction and these firewalls separate two structures or divide a structure into smaller portions to prevent the spread of fire. The lightweight construction and trusses are designed to support only their own weight. During a fire, if one fails, a domino effect happens and all fail rapidly within 5 to 10 minutes. Prolonged exposure to fire may result in structural collapse and injury or death of the occupants of the building under construction. Fire safety on construction sites is still in its primitive stages in India. There is a great necessity to improve fire safety on construction sites to protect construction workers and other occupants of the buildings. This study aims to design and implement fire safety systems for construction sites, thereby enhancing the standards to meet the system requirements at par with global standards.

Subnetwork with two nodes shared with entire ventilation network can be separated as its part. For the network under common ventilation conditions, one of these nodes will become the subnetwork starting node, while the other will be the subnetwork end node. According to the graphs theory, such a piece of the network can be considered as a subgraph of the graph representing the entire ventilation network. A special feature of that subgraph is lack of predecessors of the subnetwork starting node and lack of successors of the subnetwork end node. Ventilation district of a mine may be often treated as a subnetwork. Vicinity is a part of the network which is not separated as subnetwork. In the case of a ventilation district its vicinity forces air flow through the district. The alternative characteristic curve of the vicinity can therefore be compared to the characteristics curve of a fictional fan that forces the airflow in the district.

The alternative characteristics (later in the text: the characteristics) of the vicinity of the ventilation district in an underground mine strongly influence air quantity and therefore play a crucial role in the reduction of methane, fire and thermal hazards. The role of these characteristics and proper selection of their approximating function were presented in the article.

The reduction of resistance of an intake stopping (having influence on entire resistance of a ventilation district) produces increased airflow in the district. This changes of airflow in the district caused by a variation in internal resistance (e.g. by opening an internal regulation stopping) depends on the characteristic of the vicinity of the district. Proper selection of its approximating function is also important for this matter.

The methods of determination of the alternative characteristic curve of the district vicinity are presented. From these procedures it was possible to obtain the results of air quantities and differences in isentropic potentials between an inlet and an outlet to/from the ventilation district. Following this, the characteristics were determined by graphic and analytic methods. It was proved that, in contrast to flat vicinity characteristics, steep ones have a smaller influence on the airflow modification in the district (which are caused by a regulation of the district resistance). The characteristic curve of the vicinity determines the ability to regulate air quantity and velocity in the district.

There are approx. 250 coal waste dumping grounds in Poland, yet there are countries in which this number is even higher. One of the largest sites for depositing mining and power plant waste in the Upper Silesian Coal Basin is the Przezchlebie dumping ground. In the article, it is considered as a secondary deposit of raw materials. An assessment of mining waste collected on the Przezchlebie dumping ground was carried out in terms of its impact on the environment and the possibility of its use. Mining waste samples were tested to determine their chemical composition. Physicochemical properties and chemical compositions of water extracts obtained from the investigated waste and groundwater in the vicinity of the dumping ground were analyzed. Due to the fire hazard resulting from the natural oxidation process of chiefly carbonaceous matter and pyrite, the thermal condition of the dumping ground was assessed. The results of the obtained tests confirmed the slight impact of mining waste deposited on the Przezchlebie dumping ground on the environment. The chemical composition, low radioactive activity of waste itself and the results of water extract tests referred to the permissible values according to the Polish Journal of Laws allow for multi-directional waste management. Due to the significant carbon content, the risk of self-ignition poses a significant threat on the dumping ground. Re-mining of the dumping ground and the recovery of raw materials, including coal contained in waste, will eliminate the risk of fire, allowing for a wider use of waste and, at the same time, will allow for other benefits, e.g. in the form of financial resources and the possibility of managing the dumping ground area.

A large amount of solid and liquid wastes produced by mines and mills each year needs to be managed and minimized by alternative disposal methods like paste and dry stack. Increasingly strict environmental legislation and cost competitiveness also dictate the utilization of technically suitable, economically viable, environmentally acceptable, and socially responsible techniques. This paper reviews some of these techniques that could potentially reduce large volumes of mine wastes (with a focus on mine tailings and waste rocks) without causing significant environmental hazards. The new emerging techniques such as environmental desulphurization, covers built with sulphide-free tailings, co-disposal of tailings and waste rocks, geotextile tube dewatering, and use of tailings in the cement production and road construction for both industrial and environmental purposes are discussed in terms of waste minimization. The existing methods and approaches for efficient waste treatment and disposal are also discussed in this review paper.