The analysis of after reclamation dusts generated during the reclamation treatment of test portions of two kinds of polydispersive material in the Regmas device, is presented in the hereby paper. For the comparative purpose the fresh moulding sand marked as quartz sand „Sibelco” –1K 0.40/0.32/0.20, J88, >14000C, WK = 1.20 (acc. PN-83/H-11077), as well as the spent moulding sand, which was previously subjected to the primary reclamation and to dedusting, were used. Conditions of the process treatment were forced by the frequency of supplying the vibratory drive motors being successively 40, 50 and 60Hz for 5, 10 and 15 min. and by causing a diversified material flow through the functional system of the device (charging hopper, abrasive chamber acting as a buffer space). Two states of the process treatment, when a material was flowing through the chamber, were applied. In the first one, an intergranular surface abrasion of grains occurred as a result of the granular material circulation in the chamber forced by the vibratory drive. In the second one, the forced material flow was performed in the presence of crushing elements (steel balls), additionally introduced into the abrasive chamber. Analyses of the device influence were performed by determinations of the amount of dusts separated in the pneumatic classifier and analysis of their grain sizes by means of Analysette 22NanoTec.

The results of investigations of spent moulding sands taken from the mould in which the metal core cooling system - to increase the

cooling rate of the ladle casting - was applied, are presented in the hereby paper. The changes of the spent moulding sand at the casting

external side being the result of degradation and destruction processes of organic binder, were analysed in this publication. Since the

reclaimed material, obtained as a result of the mechanical reclamation of spent sands of the same type, is used as a grain matrix of the

moulding sand, the amount of a binder left from the previous technological cycle is essential for the sound castings production. On the

bases of investigations of the thermal analysis, ignition losses, dusts contents and pH values of the samples taken from the spent sand the

conditions under which the process of gases displacing in the casting mould was realised as well as factors limiting the efficient mould

degassing - were considered in this study. The possible reason of a periodical occurrence of an increased number of casting defects due to

changing gas volume emission, being the reason of the realised technological process, was indicated.

The results of investigations of thermal reclamation of spent moulding sands originating from an aluminum alloy foundry plant are

presented in this paper. Spent sands were crushed by using two methods. Mechanical fragmentation of spent sand chunks was realized in

the vibratory reclaimer REGMAS. The crushing process in the mechanical device was performed either with or without additional

crushing-grinding elements. The reclaimed material obtained in this way was subjected to thermal reclamations at two different

temperatures. It was found that a significant binder gathering on grain surfaces favors its spontaneous burning, even in the case when

a temperature lower than required for the efficient thermal reclamation of furan binders is applied in the thermal reclaimer. The burning

process, initiated by gas burners in the reclaimer chamber, generates favorable conditions for self-burning (at a determined amount of

organic binders on grain surfaces). This process is spontaneously sustained and decreases the demand for gas. However, due to the

significant amount of binder, this process is longer than in the case of reclaiming moulding sand prepared with fresh components.

The results of investigations of spent moulding sands taken from the mould at various distances from the surface of the produced casting,

are presented in the paper. The casting mould was made with an application of the cooling system of the metal core in order to increase the

cooling rate of the ladle casting. As temperature measurements in the mould indicated the heat flow from the metal did not create

conditions for the complete burning of a moulding sand. The analysis was performed to find out changes of spent moulding sands caused

by degradation and destruction processes of organic binders. Conditions occurring in the casting mould were discussed on the bases of

testing: ignition losses, dusts contents, pH reactions and the surface morphology of the moulding sand samples. Factors limiting the

effective mould degassing were pointed out. Operations, possible for realization, which can limit the reasons of a periodical occurrence of

increased amounts of casting defects due to changing gas evolution rates being the result of the technological process, were also indicated.