Recently, the rapid advancement of the IT industry has resulted in significant changes in audio-system configurations; particularly, the audio over internet protocol (AoIP) network-based audio-transmission technology has received favourable evaluations in this field. Applying the AoIP in a certain section of the multiple-cable zone is advantageous because the installation cost is lower than that for the existing systems, and the original sound is transmitted without any distortion. The existing AoIP-based technology, however, cannot control the audio-signal characteristics of every device and can only transmit multiple audio signals through a network. In this paper, the proposed Audio Network & Control Hierarchy Over peer-to-peer (Anchor) system enables all audio equipment to send and receive signals via a data network, and the receiving device can mix the signals of different IPs. Accordingly, it was possible to improve the system-application flexibility by simplifying the audio-system configuration. The research results confirmed that the received audio signals from different IPs were received, mixed, and output without errors. It is expected that Anchor will become a standard for audio-network protocols.

The association of phytoplasma was investigated in sand olive [Dodonaea viscosa ssp. Angustifolia (L. f.) J.G. West], cowpea [Vigna unguiclata (L.)] Wap and alfalfa (Medicago sativa L.) plants exhibiting witches broom, fasciation and little leaf symptoms, respectively. Sequence analysis of ~1.7 kb DNA fragments amplified by P1/P7 primer set confirmed the association of ‘Candidatus Phytoplasma aurantifolia’ within symptomatic alfalfa, while ‘Ca. Phytoplasma cynodontis’ was associated within cowpea and sand olive.

The discovery of (BaxCa1-x)(ZryTi1-x)O3 lead-free ceramics drawn a lot of attention to those novel materials because of their excellent piezoelectric properties. However, quite a little attention has been paid to other features of the material. This article reports a wide range of research, including composition, structure and microstructure, dielectric response and impedance spectroscopy in order to systematize and expand knowledge about this peculiar ceramics and strontium doping effect on its properties. In order to test that influence a series of samples with various strontium concentration, precisely the admixtures of 0.02, 0.04 and 0.06 mol% were prepared, as well as basic ceramics to compare obtained results.

Super-resolution image reconstruction utilizes two algorithms, where one is for single-frame image reconstruction, and the other is for multi-frame image reconstruction. Singleframe image reconstruction generally takes the first degradation and is followed by reconstruction, which essentially creates a problem of insufficient characterization. Multi-frame images provide additional information for image reconstruction relative to single frame images due to the slight differences between sequential frames. However, the existing super-resolution algorithm for multi-frame images do not take advantage of this key factor, either because of loose structure and complexity, or because the individual frames are restored poorly. This paper proposes a new SR reconstruction algorithm for images using Multi-grained Cascade Forest. Multi-frame image reconstruction is processed sequentially. Firstly, the image registration algorithm uses a convolutional neural network to register low-resolution image sequences, and then the images are reconstructed after registration by the Multi-grained Cascade Forest reconstruction algorithm. Finally, the reconstructed images are fused. The optimal algorithm is selected for each step to get the most out of the details and tightly connect the internal logic of each sequential step. This novel approach proposed in this paper, in which the depth of the cascade forest is procedurally generated for recovered images, rather than being a constant. After training each layer, the recovered image is automatically evaluated, and new layers are constructed for training until an optimal restored image is obtained. Experiments show that this method improves the quality of image reconstruction while preserving the details of the image.

A SrTiO3 electroceramic with perovskite structure was produced by the calcination of a mixture of SrCO3 and TiO2 intensively grounded by high energy milling. For this purpose, raw materials were mixed in stoichiometric amounts in a planetary type mill; the obtained powder mixture was calcined for 2 h at temperatures between 800 and 1300°C. Samples resulting from the calcination were characterized by XRD, FTIR, SEM analysis and electrical measurements. From XRD, it was determined that the SrTiO3 formed presents the cubic structure of perovskite. The complete reaction for SrTiO3 compound formation occurs at 1200°C. Micrograph observations indicate the presence of a homogeneous microstructure with tiny grain size. The measured values of electrical resistivity were within the typical range of insulating materials.

The microstructure of Al-Si alloy has coarse silicon and this structure is known dangerous for mechanical properties due to its crack effect. Sr addition is preferred to modify the coarse silica during solidification. Additionally, bifilms (oxide structure) are known as a more dangerous defect which is frequently seen in light alloys. It is aimed at that negative effect of bifilms on the properties of the alloys tried to be removed by the degassing process and to regulate the microstructure of the alloy. In this study, the effect of degassing and Sr modification on the mechanical properties of AlSi12Fe alloy was investigated, extensively. Four different parameters (as-received, as-received + degassing, Sr addition, Sr addition + degassing) were studied under the same conditions environmentally. The microstructural analyses and mechanical tests were done on cast parts. All data obtained from the experimental study were analyzed statistically by using statistical analysis software. It was concluded from the results that Sr addition is very dangerous for AlSi12Fe alloy. It can be suggested that to reach high mechanical properties and low casting defects, the degassing process must be applied to all castings whereas Sr addition should not be preferred.