The article presents the results of permeability measurements of a zirconium alcohol coating applied on moulds and cores. The introduction extensively discusses the reasons for the application of protective coatings, as well as their advantages and disadvantages. Also, the problems related to the application of protective coatings are presented i.e. limited permeability and thus the possibility of the presence of gas-originated defects in the casts. Next, the paper discusses the methods of measuring the permeability of protective coating proposed by Falęcki and Pacyniak. The study also presents an indirect permeability measurement method. For the investigations, zirconium alcohol coatings with the three conventional viscosities 10, 20 and 30s were used. The viscosity was determined by means of the Ford cup with the clearance of 4mm. The coatings were applied onto profiles of Φ 50 x 50 mm, made of moulding sand consisting of a sand matrix with the mean grain size of dL = 0,11, 17, 24, 31 and 34 mm and phenol-formaldehyde resin. The effect of the matrix grain size on the permeability of the sand with and without a coating was determined.

The study presents the possible use of optoelectronic system for the measurement of values specific for hydrodynamics of two-phase gas very-high-viscosity liquid flow in vertical pipes. An experimental method was provided, and the findings were presented and analysed for selected values which characterise the two-phase flow.

The nanocomposites based on water glass matrix were attempted in the study. Nanoparticles of ZnO, Al2O3 or MgO in organic solutions

were applied into water glass matrix in the amounts of: 1.5; 3; 4 or 5 mas. %. Wettability of the quartz sad by the nanocomposites based on

water glass matrix was determined by testing changes of the wetting angle θ in time τ for the system: quartz – binder in non-stationary

state, by means of the device for measuring wetting angles. Wettability measurements were carried out under isothermal conditions at an

ambient temperature (20 – 25 oC). The modification improves wettability of quartz matrix by water glass, which is effective in improving

strength properties of hardened moulding sands. Out of the considered modifiers in colloidal solution of propyl alcohol water glass

modified by MgO nanoparticles indicated the smallest values of the equilibrium wetting angle θr. This value was equal app. 11 degrees and

was smaller no less than 40 degrees than θr value determined for not modified water glass. Viscosity η of nanocomposites based on water

glass matrix was determined from the flow curve, it means from the empirically determined dependence of the shearing stress τ on shear

rate γ: τ = f (γ) (1), by means of the rotational rheometer. Measurements were carried out at a constant temperature of 20 oC. The

modification influences the binder viscosity. This influence is conditioned by: amount of the introduced modifier as well as dimensions and

kinds of nanoparticles and organic solvents. The viscosity increase of the modified binder does not negatively influence its functional

properties.

This study presents the rheological properties of sewage sludge after conditioning with the application of biomass ash. The impact of sewage sludge pre-treatment on its viscosity, flow curves and thixotropy was investigated. The increase of shear stress and the decrease of viscosity were observed with the increase of shear rate. Obtained results were compared with raw sewage sludge and the sludge after modification by means of polyelectrolyte in the dosage of 1.5 g (kg d.m.)^-1. The findings proved that samples of raw and conditioned sewage sludge had thixotropic characteristics. The correlation between moisture content and capillary suction time reduction as well as selected rheological parameters were also determined. On the basis of the obtained results it was stated that the Ostwald de Vaele model best fits the experimental data.

This article presents measurements of the thickness of alcohol-based coatings on sand foundry cores and moulds. These coatings were applied using two methods, the dipping method and the painting method. For the purposes of the study, a zircon alcohol-based coating was prepared with three different levels of nominal viscosity; very thin at 10s, average at 20s, and thick at 30s. The coating was applied to a core made of quartz sand and furan resin. The cores were made of sand with three different grain sizes; dL = 0.22 mm – fine sand, dL = 0.33 mm medium sand, and dL = 0.47 mm coarse sand. In the study, the thickness of the coating obtained to the core was measured immediately after application as well as after drying. Additionally, the extent of penetration into the intergranular spaces of the core matrix was measured. On the basis of this study, the impact of the grain size of the core matrix on the thickness of the coating and its penetration into the core was assessed. The thickness of coatings obtained using different application methods was also assessed.

The role of slag in the process of continuous casting of steel (CCS) is reduced to the thermal and chemical insulation of the liquid steel surface, and additionally to refining. The ability to adsorb non-metallic inclusions flowing off from the crystallizer, mainly Al2O3, determines its physicochemical properties. As a result of adsorption and dissolution of inclusions tin he liquid layer the viscosity and thickness of mould flux change, which eventually affects the technological parameters and behavior of slag in the crystallizer. The influence of aluminum oxide on the viscosity of slag was empirically investigated with a structural viscosity model worked out by Nakamoto. The results of the simulation are presented in the form of plots. Authors observed a significant influence of Al2O3 on the slag viscosity, which suggests that this effect should be taken into account when selecting chemical composition of mould flux for definite types of steel. The results of calculations also show that the disturbances in casting caused by the use of the mould slag may be connected with the content of non-metallic inclusions in steel.

An axially symmetric, gravity driven, steady flow of a grounded polar ice sheet with a prescribed temperature field is considered.

The ice is treated as an incompressible, non-linearly viscous, anisotropic fluid, the internal structure (fabric) of which evolves as ice descends from the free surface to depth in an ice sheet. The evolution of the ice fabric is described by an orthotropic constitutive law which relates the deviatoric stress to the strain-rate, strain, and three structure tensors based on the current (rotating) principal stretch axes. The solution of the problem is constructed as a leading-order approximation derived from asymptotic expansions in a small parameter that reflects the small ratio of stress and velocity gradients in the lateral direction of the ice sheet to those in the thickness direction. Numerical simulations of the flow problem have been carried out for various sets of rheological parameters defining the limit strength of the anisotropic fabric in ice. The results of calculations illustrate the influence of the ice anisotropy, basal melt conditions and temperature field in ice on the glacier thickness and lateral span, and on the depth profiles of the flow velocity.

In this paper, the authors analyse the propagation of surface Love waves in an elastic layered waveguide (elastic guiding layer deposited on an elastic substrate) covered on its surface with a Newtonian liquid layer of finite thickness. By solving the equations of motion in the constituent regions (elastic substrate, elastic surface layer and Newtonian liquid) and imposing the appropriate boundary conditions, the authors established an analytical form of the complex dispersion equation for Love surface waves. Further, decomposition of the complex dispersion equation into its real and imaginary part, enabled for evaluation of the phase velocity and attenuation dispersion curves of the Love wave. Subsequently, the influence of the finite thickness of a Newtonian liquid on the dispersion curves was evaluated. Theoretical (numerical) analysis shows that when the thickness of the Newtonian liquid layer exceeds approximately four penetration depths 4δ of the wave in a Newtonian liquid, then this Newtonian liquid layer can be regarded as a semi-infinite half-space. The results obtained in this paper can be important in the design and optimization of ultrasonic Love wave sensors such as: biosensors, chemosensors and viscosity sensors. Love wave viscosity sensors can be used to assess the viscosity of various liquids, e.g. liquid polymers.

This paper discusses design, evaluation, and application for the use of swirl/vortex technologies as liquid purifi cation system. A study was performed using modifi ed swirl sedimentation tanks. The vortex separators containing baffle have been studied under laboratory conditions at hydraulic load from 21 to 64 [m3/(m2·h)]. Analyzed disperser phases were municipal water and glycerol solutions of varying concentration. The pressure drop and the efficiency of purification of liquid stream were analyzed. The suspended particles of different diameters were successfully removed from liquid with the application of swirl chambers of proposed constructions. It was found that damming of liquid in the tank increases alongside liquid stream at the inlet and depends on the tank construction. The efficiency of the sedimentation tanks increases alongside the diameters of solid particles and decrease in the liquid flow rate. The best construction proved to be the one where baffle is located in the middle of in- and outlet due to the highest efficiency of the purification liquid stream for solid particles of the smallest diameter. The proposed solution is an alternative to the constructions of heavy fraction separators.