Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 4
items per page: 25 50 75
Sort by:
Download PDF Download RIS Download Bibtex

Abstract

In Eurocode 5, the stiffness equation for bolted steel-wood-steel is stated as a function ofwood density and fastener diameter only. In this research, an experimental study on various configurations of tested bolted steel-wood-steel (SWS) connections has been undertaken to predict the initial stiffness of each connection. In order to validate the Eurocode 5 stiffness equation, tests on 50 timber specimens (40 glued laminated timbers and 10 laminated veneer lumbers (LVL)) with steel plates were undertaken. The number of bolts was kept similar and the connector diameter, timber thickness, and wood density were varied. The results obtained in the experimental tests are compared with those obtained from the Eurocode 5 stiffness equation. From the analysis, it is signified that the stiffness equation specified in Eurocode 5 for bolted SWS connections does not adequately predict the initial stiffness. The results from Eurocode 5 stiffness equation are very far from the experimental values. The ratio of stiffness equation to experimental results ranges from 3.48 to 4.20, with the average at 3.77, where the equation overpredicted the experimental stiffness value for the connection. There is a need to consider or incorporated other parameters such as geometric configurations in Eurocode 5 stiffness equation to improve the ratio with the experimental data.
Go to article

Authors and Affiliations

Nur Liza Rahim
1 2
ORCID: ORCID
Gary Raftery
3
ORCID: ORCID
Pierre Quenneville
3
ORCID: ORCID
Doh Shu Ing
4
ORCID: ORCID
Marcin Nabiałek
5
ORCID: ORCID
Ramadhansyah Putra Jaya
4 6
ORCID: ORCID
Norlia Mohamad Ibrahim
1 7
ORCID: ORCID
Mohd Mustafa Al Bakri Abdullah
8 6
ORCID: ORCID
Agata Śliwa
9
ORCID: ORCID

  1. University Malaysia Perlis, Faculty of Civil Engineering Technology, 02600 Arau Perlis, Malaysia
  2. 2Sustainable Environment Research Group (SERG), Centre of Excellence Geopolymer and Green Technology (CEGeoGTech), University Malaysia Perlis (UniMAP), 01000 Kangar Perlis, Malaysia
  3. University of Auckland, Faculty of Civil Engineering, Department of Civil and Environmental Engineering, Auckland, New Zealand
  4. Department of Civil Engineering, College of Engineering, University Malaysia Pahang, 26300 Gambang Kuantan, Pahang Malaysia
  5. Czestochowa University of Technology, Czestochowa, Poland
  6. Centre of Excellence Geopolymer and Green Technology (CEGeoGTech), University Malaysia Perlis (UniMAP), 01000 Kangar Perlis, Malaysia
  7. Sustainable Environment Research Group (SERG), Centre of Excellence Geopolymer and Green Technology (CEGeoGTech), University Malaysia Perlis (UniMAP), 01000 Kangar Perlis, Malaysia
  8. University Malaysia Perlis, Faculty of Chemical Engineering Technology, 02600 Arau Perlis, Malaysia
  9. Division of Materials Processing Technology and Computer Techniques in Materials Science, Silesian University of Technology, 44-100 Gliwice, Poland
Download PDF Download RIS Download Bibtex

Abstract

Block tearing is a failure mode of steel connections based on rupture of material. In this paper, a numerical model is developed to capture fracture initiation and progression until failure in steel angles connected by one leg using single row of bolts. It was realized using Gurson-Tvergaard-Needleman porous material model, which can accurately trace the behaviour of steel at plastic and ultimate range. Obtained results are validated on laboratory test results in global and local terms. Stress distribution along the failure paths in the gross and net area subjected to shear and tension was investigated for different geometrical arrangements of connections. Observation of rupture mechanisms allowed to compare the design procedures given in Eurocode 3 with connections behaviour. Results of analysis indicate that both plastic stress distribution in gross shear area and ultimate stress distribution in net shear area can limit block tearing resistance, which is consistent with the newest code provisions.
Go to article

Authors and Affiliations

Edyta Bernatowska
1
ORCID: ORCID
Lucjan Ślęczka
1
ORCID: ORCID

  1. Rzeszow University of Technology, Faculty of Civil and Environmental Engineering and Architecture, Poznanska 2 Street, 35-084 Rzeszow,
Download PDF Download RIS Download Bibtex

Abstract

In civil engineering structures, steel angles are often used as tensioned elements, because of their ease of fabrication and assembly. For practical reasons, angles are usually connected only by one leg, using a single row of bolts, and rupture of weakened section usually determines a joint capacity. Also, eccentricity affects the distribution of stresses in the net section and hence its load capacity. Assessment of ultimate resistance is a completely different issue compared to the well-known and established problems of plastic resistance and requires advanced material modelling. The paper presents a numerical simulation of net section failure of tensioned angles, made of structural steel grade S275, taking into account ductile initiation and propagation of fracture using the Gurson–Tvergaard– Needleman damage model. Extensive parametrical analysis of ultimate tensile resistance was performed with a wide range of parameters. The typical and well-recognised failure modes were observed as net section fracture and block tearing. Also, an additional failure mode, classified as limited block tearing, has occurred which is not considered in current design provisions. The paper describes the impact of individual geometrical properties of the joint (numbers of bolts, connection length, and distance from the edge of the connected leg to the center of the fastener hole) on the apparent failure form and the resistance obtained.
Go to article

Authors and Affiliations

Edyta Bernatowska
1
ORCID: ORCID
Lucjan Ślęczka
1
ORCID: ORCID

  1. Rzeszów University of Technology, Faculty of Civil and Environmental Engineering and Architecture, Poznanska 2, 35-084 Rzeszów, Poland
Download PDF Download RIS Download Bibtex

Abstract

Steel-wood-steel connection is widely seen in many applications, such as timber structures. The stiffness of steel-wood-steel connection loaded parallel to grain for softwoods originated from Malaysia was investigated in this study. Numerical models have been developed in ABAQUS to study the stiffness connection. Softwoods of Damar Minyak and Podo have been selected in this analysis. The comprehensive study focused on the effect of bolt configurations on stiffness. Numerical analysis is carried out and the developed model has been validated with the previous study. Further investigations have been made by using the validated model. From this model, numerical analysis of the stiffness values have been made for various bolt configurations, including bolt diameter, end distance, bolt spacing, number of rows and bolts and edge distance. The result shows that the stiffness of bolted timber connections for softwood depends on the bolt diameter, number of rows and bolts, end distance and edge distance. Based on the result, stiffness increased as the diameter of the bolt, end distance, number of rows and bolts and edge distance increased. It is also discovered that the stiffness equation in Eurocode 5 (EC5) is inadequate as the equation only considered parameters which are wood density and bolt diameter. Other connection parameters such as geometry are not considered in the EC5 equation.
Go to article

Authors and Affiliations

Nur Liza Rahim
1 2
ORCID: ORCID
Francis Ting Shyue Sheng
1
ORCID: ORCID
Abdul Razak Abdul Karim
3
ORCID: ORCID
Marcin Nabialek
4
ORCID: ORCID
Mohd Mustafa Al Bakri Abdullah
5 6
ORCID: ORCID
Marek Sroka
7
ORCID: ORCID

  1. Universiti Malaysia Perlis, Faculty of Civil Engineering Technology, 02600 Arau Perlis, Malaysia
  2. Sustainable Environment Research Group (SERG), Centre of Excellence Geopolymer and Green Technology (CEGeoGTech), Universiti Malaysia Perlis (UniMAP), 01000 Kangar Perlis, Malaysia
  3. Faculty of Engineering, University of Malaysia, Sarawak, 94300 Kota Samarahan, Sarawak, Malaysia
  4. Department of Physics, Faculty of Production Engineering and Materials Technology, Czestochowa University of Technology, Czestochowa, Poland
  5. Universiti Malaysia Perlis, Faculty of Chemical Engineering Technology, 02600 Arau Perlis, Malaysia
  6. Centre of Excellence Geopolymer and Green Technology (CEGeoGTech), Universiti Malaysia Perlis (UniMAP), 01000 Kangar Perlis, Malaysia
  7. Division of Materials Processing Technology and Computer Techniques in Materials Science, Silesian University of Technology, 44-100 Gliwice, Poland

This page uses 'cookies'. Learn more