Air abrasion process is used for cleaning casting surface of prosthetic components, and to prepare the surface of these elements for the

application of veneering items. Its side effect, however, is that abrasive particles are embedded in the treated surface, which can be up to

30% of the surface and it constitutes the side effect of this procedure. Such a significant participation of foreign material can not be

indifferent to the properties of the surface. Embedded particles can be the place of stress concentration causing cracking of ceramics, and

may deteriorate corrosion resistance by forming corrosive microlinks. In the latter cases, it would be advisable to remove elements

embedded into the surface. The simplest method is chemical etching or electrochemical one. Nevertheless, these procedures should not

significantly change the parameters of the surface. Among many possible reagents only a few fulfills all the above conditions. In addition,

processing should not impair corrosion resistance of titanium, which is one of the most important factors determining its use as a prosthetic

restoration in the mouth. The study presented results of corrosion resistance of titanium used to make prosthetic components by means of

casting method, which were subjected to chemical processing designed to remove the embedded abrasive particles. The aim of the study

was to investigate whether etching with selected reagents affects the corrosion resistance of titanium castings. For etching the following

reagents were used: 30% HNO3 + 3% HF + H2O, HNO3+ HF+ glycerol (1:2:3), 4% HF in H2O2, 4% HF in H2O, with a control

sandblasted sample, not subjected to etching. Tests demonstrated that the etching affected corrosion properties of test samples, in each case

the reduction of the corrosion potential occurred - possibly due to the removal of particles of Al2O3 from the surface and activation of the

surface. None of the samples underwent pitting corrosion as a result of polarization to 9 V. Values of the polarization resistance, and

potentiodynamic characteristics indicated that the best corrosion resistance exhibited the samples after etching in a mixture of 4% solution

of HF in H2O2. They showed very good passivation of the surface.

Selective Laser Melting (SLM) is a modern manufacturing method with many applications in medicine, aerospace and automotive industries. SLM processed materials are characterized by good dimensional accuracy and properties comparable or superior to materials obtained by traditional processing methods. In this paper an SLM process was used to obtain 316L stainless steel parts. This paper presents the microstructure, chemical and phase composition, physicochemical and electrochemical properties of 12 groups of tested samples, differentiated by the SLM processing parameters. Based on the investigation, it can be inferred that the selection of the appropriate SLM parameters is very important to determined final material properties. The samples produced with the energy density E = 600 J/mm3 were observed to possess optimum properties – a homogeneous structure, density closest to the desired one, good wettability and pitting corrosion resistance.

The paper presents the results of research on nanocomposite nickel/graphene oxide (Ni / GO) coatings produced by electrochemical reduction method on a steel substrate. Discussed is the method of manufacturing composite coatings with nickel matrix and embedded graphene oxide flakes. For comparative purposes, the studies also included a nanocrystalline Ni coating without embedded graphene oxide flakes. Graphene oxide was characterized by Raman spectroscopy, infrared spectroscopy (FTIR) and transmission (TEM) and scanning (SEM) electron microscopy. Results of studies on the structure of nickel and composite Ni/GO coatings deposited in a bath containing different amount of graphene oxide are presented. The coatings were characterized by scanning electron microscopy, light microscopy, Raman spectroscopy and X-ray diffraction. The adhesion of the prepared coatings to the substrate was examined by the scratch method. The microhardness of the coatings was measured using the Vickers method on perpendicular cross-sections to the surface. Corrosion tests of the coatings were investigated using the potentiodynamic method. The influence of graphene oxide on the structure and properties of composite coatings deposited from baths with different content of graphene oxide was determined.

Corrosion is a main problem for longtime exploration of heat exchangers in automotive industry. Proper selection of accelerated corrosion test for newly developed material is a key aspect for aluminum industry. The selection of material based on corrosion test includes test duration, chemical spray composition, temperature and number of cycles. The paper present comparison of old and newly developed accelerated corrosion tests for testing automotive heat exchanger. The accelerated test results are comprised with heat exchanger taken from market after life cycle.