The radiation of sound waves from partially lined duct is treated by using the mode-matching method in conjunction with the Wiener-Hopf technique. The solution is obtained by modification of the Wiener-Hopf technique and involves an infinite series of unknowns which are determined from an infinite system of linear algebraic equations. Numerical solution of this system is obtained for various values of the problem parameters, whereby the effects of these parameters on the sound diffraction are studied. A perfect agreement is observed when the results of radiated field are compared numerically with a similar work existing in the literature.

Increasing of the efficiency of convective cooling of the inner surface of a short duct by changing its geometry was studied by the use of electrochemical limiting current technique (ELDCT). The duct consisted of seven identical, cylindrical segments. The changes of the duct geometry were obtained by mutual displacement of neighbouring segments, towards the radial direction. Mean values of the mass transfer coefficient for each segment and friction losses for the whole channel were measured for Reynolds numbers spanning the range 7700–35300 at the five values of displacement parameter. The results were used for estimation of cooling efficiency. Recommended values of displacement were determined to point the favourable conditions of heat/mass transfer in the duct. The results may be used, e.g. in the design of heat exchangers and channels for cooling of turbine blades and electronic equipment.

Radiation of sound waves from a semi-infinite cylindrical duct with perforated end whose outer wall is coated with acoustically absorbent material is investigated by using the Wiener-Hopf technique in conjunction with the mode matching technique. A semi-infinite duct with a perforated screen can be used as a model for many engineering applications, such as noise reduction in exhausts of automobile engines, in modern aircraft jet, and turbofan engines. In particular, we aim to find the effects of outer lining and perforated end to sound pressure level for the underlying problem by using the standard Wiener-Hopf and mode matching techniques. We also present some numerical illustrations by determining the sound pressure level for different parameters such as soft and rigid outer surface, with and without perforated end, etc. Such investigations are useful in the reduction of noise effects generated through variety of sources.

In the present work, the radiation of sound waves from a coaxial duct is considered. This coaxial duct has an inner wall which is infinite and has piecewise acoustically absorbent material, while the outer wall is semi-infinite and rigid. The analytical solution of the problem is found by means of the Wiener-Hopf technique. Applying the Fourier transformation to the boundary value problem, the explicit expression for the scattered field is obtained. In the end, some numerical results are displayed for different parameters and compared to rigid case.

Scattering of sound waves in two stepped cylindrical duct which walls are coated with different acoustically absorbent materials is investigated by using Wiener-Hopf technique directly and by determining scattering matrices. First, by using Fourier transform technique we obtain a couple of modified Wiener-Hopf equations whose solutions involve four sets of infinitely many unknown expansion coefficients providing systems of linear algebraic equations. Then we determine scattering matrices of the problem and we state the total transmitted field by using generalized scattering matrix method. Numerical results are compared for different parameters.

Artificial roughness has been found to enhance the thermal performance from the collector to air in the solar air heater duct. This paper presents the results of experimental investigation on thermal performance of three sides solar air heater roughened with combination of multiple-v and transverse wire. The range of variation of system and operating parameters is investigated within the limits of relative roughness pitch of 10−25, relative roughness height of 0.018−0.042, angle of attack of 30°−75° at varying flow Reynolds number in the of range of 3000−12000 for fixed value of relative roughness width of 6. The augmentation in fluid temperature flowing under three side’s roughened duct is found to be 36.57% more than that of one side roughened duct. The maximum thermal efficiency is obtained at relative roughness pitch of 10 and relative roughness height of 0.042, and angle of attack of 60°. The augmentation in thermal efficiency of three sides over those of one side roughened duct is found to be 46−57% for varying values of relative roughness pitch, 38−50% for varying values of relative roughness height, and 40−46% for varying values of angle of attack.

Numerical predictions of heat transfer under laminar conditions in a square duct with ribs are presented in this paper. Ribs are provided on top and bottom walls in a square duct in a staggered manner. The flow rates have been varied between Reynolds number 200 and 600. Various configurations of ribs by varying length, width and depth have been investigated for their effect on heat transfer, friction factor and entropy augmentation generation number. Further artificial neural network integrated with genetic algorithm was used to minimize the entropy augmentation generation number (performance factor) by selecting the optimum rib dimensions in a selected range. Genetic algorithm is compared with microgenetic algorithm to examine the reduction in computational time for outlay of solution accuracy.

In the present work, an approach to obtain a design method for the size of the plenum chamber cross-section of a marine gas turbine air supply system has been investigated. Flow in ducts makes noise which is very high in the turbine inlet part because of the large amount of flow. Therefore, this phenomenon should be considered in the design process. A suitable approach to design the duct is proposed (considering acoustic and aerodynamic performance at the same time). In this method, an air supply channel system of the marine gas turbine has been categorized into three sections according to the requirements of the aerodynamic and acoustic; inlet, plenum chamber, and outlet channels with circular cross-sections. The geometrical dimensions of inlet and outlet channels have been determined using the plane waves theory about a channel, in which the effects of flow is ignored. Space limitations of battleships at the dominant frequency have been considered. Then, the optimized size of the mid-channel section, in terms of both aerodynamic and acoustic requirements, using numerical methods and regarding the effects of flow has been calculated. Various 3D turbulent flows inside the plenum chamber have been considered, in which large eddy simulation turbulence model is utilized. Ffowcs, Williams and Hawkings models are used for the sound propagation process based on the Lighthill integral equation. The validity of the simulation has been checked by comparing results (sound pressure level) with experimental data obtained from a chamber. The comparison revealed the acceptable errors for a variety of frequencies. The results disclosed that the performance of channel system aerodynamic decreased when the fraction of plenum chamber cross-section to inlet/outlet channel cross-section increased. With an increase in the cross-section size at first Acoustic performance is improved and then worsen. Six different cases of marine gas turbine air supply system configurations have been presented, in which the limitation of the battleship space is considered. Examining and comparing the acoustic performance of different cases of the air supply channel system, it was found that the amount of sound pressure level, around the air supply channel system, and the high-pressure sound area can move along the air supply channel system. Additionally, deviations from plane waves considering the effects of flow have been inspected in all cases. The reason for this deviation is the effects of the airflow through the channel system and quadrupole sources in the production of sound in the channel system, which causes higher modes.