The effect of aging time at 850°C for 300 s, 600 s, 1800 s, and 84600 s on the microstructural evolution and corrosion resistance of 2205 duplex stainless steel (DSS) was studied after cold rolling up to 60% of reduction. X-ray diffraction, scanning electron and transmission electron microscopy were used for microstructural characterization. The corrosion behavior was studied by cyclic potentiodynamic polarization (CPP) and electrochemical impedance technique (EIS) in 3.5% NaCl solution and the susceptibility to sensitization was investigated through the double loop electrochemical potentiodynamic reactivation (DL-EPR) test in 0.5 M H2SO4 + 0.1 M NaCl + 0.002 M KSCN solution. After cold working, increasing aging time led to an increase in sigma phase precipitation and a decrease in pitting corrosion resistance. However, the ultrafine microstructure had a beneficial influence on the self-healing effect in Cr and Mo depleted areas with the increasing of aging time, resulting in higher passivation ability. The DSS 2205 type was not susceptible to intergranular corrosion for the aged conditions applied.

The microstructure and corrosion properties of spark plasma sintered yttria dispersed and yttria free duplex and ferritic stainless samples were studied. Spark plasma sintering (SPS) was carried out at 1000°C by applying 50 MPa pressure with holding time of 5 minutes. Linear sweep voltammetry (LSV) tests were employed to evaluate pitting corrosion resistance of the samples. Corrosion studies were carried out in 0.5, 1 and 2 M concentration of NaCl and H2SO4 solutions at different quiet time of 2, 4, 6, 8 and 10 seconds. Yttria dispersed stainless steel samples show more resistance to corrosion than yttria free stainless steel samples. Pitting potential decreases with increase in reaction time from 2 to 10 seconds. Similarly, as concentration of NaCl and H2SO4 increases from 0.5 M to 2 M the corrosion resistance decrements due to the availability of more Cl¯ and SO4 2¯ ions at higher concentration.

The dry sliding wear behavior of heat-treated super duplex stainless steel AISI 2507 was examined by taking pin-on-disc type of wear-test

rig. Independent parameters, namely applied load, sliding distance, and sliding speed, influence mainly the wear rate of super duplex

stainless steel. The said material was heat treated to a temperature of 850°C for 1 hour followed by water quenching. The heat treatment

was carried out to precipitate the secondary sigma phase formation. Experiments were conducted to study the influence of independent

parameters set at three factor levels using the L27 orthogonal array of the Taguchi experimental design on the wear rate. Statistical

significance of both individual and combined factor effects was determined for specific wear rate. Surface plots were drawn to explain the

behavior of independent variables on the measured wear rate. Statistically, the models were validated using the analysis of variance test.

Multiple non-linear regression equations were derived for wear rate expressed as non-linear functions of independent variables. Further,

the prediction accuracy of the developed regression equation was tested with the actual experiments. The independent parameters

responsible for the desired minimum wear rate were determined by using the desirability function approach. The worn-out surface

characteristics obtained for the minimum wear rate was examined using the scanning electron microscope. The desired smooth surface was

obtained for the determined optimal condition by desirability function approach.

This paper presents an investigation into effect of nitrogen content of shielding gas mixture on weld geometry, microstructure and hardness of pulsed laser welded 2205 duplex stainless steel. Full penetration autogenous welding was performed on 2 mm thick plates using a low power pulsed Nd: YAG laser. light and scanning electron microscopy were used to study the resulting microstructures. It is observed that 2 mm full penetrated joint decreases to 1.8 mm by dominating nitrogen in argon-nitrogen mixture. Different morphologies of austenite phase as well as an increase of 8% of its content can be observed in pure nitrogen shielded welds. Average weld grain size in sample which is welded in nitrogen atmosphere stands at approximately 41 μm which is smaller than that of argon atmosphere which is about 51 μm. Micro-hardness test reveals that hardness values increase from 280 HV in base metal to 307 HV in weld center line and the shielding gas mixture does not significantly influence the weld hardness.